-
Anonymous users2024-02-07Didn't unlock the anti-theft look.,One-click start?。
-
Anonymous users2024-02-06If the instrument indicator is not lit, first check the power supply fuse of the dashboard, and replace it if it is blown. Disassemble the dashboard, the lights are generally at the back of the dashboard, replace the lights that are not lit, and generally the individual lights are not lit to indicate that there is no problem with the fuse and wire, the main reasons are as follows
1. The lamp of the dashboard is damaged and needs to be replaced in time;
2. If the power supply line of the dashboard is broken, there is an open circuit or short circuit, which will also cause the car dashboard to not light up;
3. If the power supply fuse of the car dashboard is broken, there will naturally be no power supply, and the dashboard will not light up.
Precautions in the use of the car dashboard:
1. When the indicator light is on, the odometer should be observed immediately, if the cumulative mileage reaches or exceeds l00,000km, the timing toothed belt must be replaced, otherwise the timing toothed belt may break, so that the engine can not work normally.
2. After replacing the new timing toothed belt, it is necessary to open the rubber plug outside the reset switch on the mileage dial, and press the reset switch inside with a small round bar to extinguish the indicator light of the timing toothed belt.
3. After replacing the new timing toothed belt, remove the odometer and adjust all the readings on the odometer to the 0 position.
-
Anonymous users2024-02-05One situation is when the starter works, but the engine does not.
1) First of all, it may be a circuit or electronic fault. Common mechanical failures are: Electronic failure mainly refers to the loss of function of the computer control board. Also: the oil pump is out of order.
2) Then there is the oil circuit failure, and the battery has failed. The stall caused by the failure of the oil circuit often has the engine weakness, and then the key is twisted to ignite. The reason why the starter does not work is other than the battery
The time band (chain) is broken, and it would be best if you had a voltmeter on hand. Because this is when it has the most load. It is rare for two or more failures to occur at the same time.
In many cases, there is no warning, carburetor failure, low voltage circuit break. There are two situations in which the fire cannot be ignited, because it may be caused by one of many faults, and all the problems are solved.
3) Finally, it can also be a mechanical failure. There is a fault of the circuit.
The second case is that even the starter does not work or works barely work, which also indicates the aging of the battery. Sometimes it happens that the fuel tank is empty and the owner does not know the situation, there must be a problem with your battery, the ignition relay is damaged or the starter itself is damaged, and the spark plug is damaged, but it cannot be said absolutely: one is that the turning sound of the starter can be heard, and the ignition switch may be damaged.
It doesn't hurt to have a voltmeter, you can use a small 12-volt bulb and a small section of power cord instead: look at the outer wall of the battery with the naked eye: the fuse is blown out, the gas pedal is a sign of stepping on cotton, the nozzle is damaged, etc.
There are many ways to check、The center ignition line is off, and the engine does not catch fire。 The other is that after twisting the key, the oil filter is clogged, and if the voltage indication suddenly drops below 8 volts, it means that a new battery is absolutely needed. What happened was very sudden.
Only at the moment of ignition, there was no sound, and if you found that it had expanded and deformed, the oil circuit was impassable. This situation is more complicated, and the fire head is leaking. Connect the positive and negative poles of the battery, cylinder leakage without pressure, etc.
This is not surprising. At this time, the first thing that needs to be checked is the battery or battery. The same is true of the method, which is one of the most common faults of the car, but the engine does not start.
-
Anonymous users2024-02-041.Failure or damage of the dashboard lighting; 2.The power supply wire of the instrument panel is disconnected; 3.The power supply fuse of the instrument panel is blown out; Mainly check the above aspects to troubleshoot and solve the problem.
Check whether the battery clip is loose and check whether the battery has electricity.
One: Is the steering wheel in a deadbolt state? The solution is simple, as long as you hit the steering wheel hard and twist the key at the same time, you can generally unlock the steering wheel lock quickly, and the ignition is an instantaneous thing. >>>More
For example, engine fault lights, tire pressure warning lights, oil warning lights, and so on. Depending on the model, the difference will be large. It is recommended to check the vehicle instruction manual, which will have a clear explanation. >>>More
Generally speaking, the main reasons for the ABS lights on the dashboard of the Santana car are four points, one is the problem with the front wheel ABS sensor; the second is poor wiring harness contact; the third is the failure of the ABS computer controller; Fourth, check whether the ABS fuse in the engine compartment is burned or lost. So you should eliminate these problems step by step. First of all, the contact of each wiring harness should be tested to see whether the transmission of the wiring harness is good and whether there is a phenomenon of poor contact. >>>More
SEL has been used in some models of the W126 series, S is the S class, E is the electronic fuel system (in those days, this thing was still relatively advanced, like Audi's current FSI system), L of course means extended (of course, there are also SE, not lengthened models). >>>More