Request a translation into English! The fridge is broken, the fridge won t cool, the stopper in the

our fridge doesn't work,and we should contact the customer service to repair it

I hope it can help you, and if you have any questions, you can continue to ask.

Glad to answer for you :

because the food hasn't been put into the refrigirater,they are all bad.

Because it wasn't put in the refrigerator before. And this action has continued until now, so use the present perfect tense.

Causes and repair methods:

1. The exhaust outlet is blocked

The refrigerator thermostat is installed in the refrigerator, and the temperature of the refrigerator does not reach the temperature required by the thermostat, so it does not stop. If the compressor does not work around the clock, the freezer compartment may cause the refrigerant to reach the maximum refrigeration temperature. Most of this phenomenon occurs in air-cooled refrigerators.

The reason is that the evaporator flower froster in the cold room is broken, which produces an ice blockage. It cannot be ruled out that the air cooling fan is broken, and there are too many items in the refrigerator to block the air outlet, causing poor cooling effect.

2. There are too many items in the refrigerator:

The temperature of the refrigerator is automatically adjusted with the temperature adjustment of the freezer, and the temperature of the freezer can be lowered. Generally, the temperature of the refrigerator room is 4-10 degrees Celsius. Note that the higher the number of the temperature controller, the lower the temperature, the higher the number in summer and the smaller number in winter.

In addition, the refrigerator door is often opened, and there are many items in the refrigerator, resulting in the refrigerator not being refrigerated or the refrigeration effect is not ideal.

3. Compressor failure:

The reason why the refrigerator is not cooling may also be that there is a problem with the refrigerator compressor. The compressor can start, remove the return pipe and block the outlet with your fingers, check how much the downward pressure is, if it is too low, then there is a problem with the compressor, if the compressor can not start, then check whether the refrigerator power is plugged in.

What should I do if the refrigerator at home suddenly does not refrigerate, and what is the reason?

There are two reasons why it is generally not refrigerated:

First, the refrigeration switch is not turned on, and this manual start can be done;

The second is that the compressor is broken, or there is no freon, which requires professionals to repair.

Just look at the button that can adjust the cooling coefficient and how much you can adjust it to 4 5.

Since it is suddenly not refrigerated, it should be impossible to solve it by yourself, or find after-sales service.

There are many reasons for not refrigerating, the computer board is broken, the refrigerant leaks, etc. will cause the situation of not refrigerating, it is best to find after-sales service to test it.

First, check whether the refrigeration pipe is broken.

Unplug the refrigerator and cut the process port to release the residual gas, especially the refrigerator using R600 refrigerant, it is best to turn on the compressor and run for 10 15 minutes after cutting the process port (in an open place, R600 is a flammable refrigerant).

The operation diagram of refrigerator dismantling and metering is shown in the figure below.

The operation steps of type A and B are as follows: first open the process port, release the residual gas, weld open the return gas nozzle and weld the table valve; Weld the condenser pipe at 3 points, turn on the compressor, weld the meter valve at the weld that does not emit gas, turn off the power supply, weld the condenser pipe at 4 points, turn on the compressor, turn off the power supply, and weld the solder with gas at 4 points; After cutting the 5-point capillary, the two cuts are welded to death respectively; Weld the condenser pipe at 6 points and weld the table valve on the condenser pipe. Then the air pressure on the three gauge valves respectively, observe 12 24 hours, if the pressure of the three gauge valves does not drop, indicating that the anti-dew pipe is bad, remove the 3-point gauge valve, cut the mouth of the 4-point welded dead, and weld a section of 3 4m condenser pipe between them; Weld 1 point, change the filter, cut the capillary tube through the filter 2cm and weld it, weld all the solder joints, weld the table valve at the process port, test the pressure again, and check whether there is any solder joint leakage.

C-type operation steps: after opening the process port 1 first and discharging the residual gas, the return air pipe 2 is welded open and the table valve is welded; After welding the condenser pipe at 3 points, weld the table valve on the condenser pipe; Cut off the capillary at 4 points and weld the two ports to death; The return pipe gauge valve and the condenser tube gauge valve are respectively pressed to the PA pressure, and after 12 24 hours of observation, if the pressure of the condenser tube valve drops, it means that the condenser tube leaks refrigerant, and this type of refrigerator can only be solved by adding a whole condenser on the back of the refrigerator. The length of the condenser is:

Refrigerators of 185L and below are around LLM, and refrigerators from 192L to 228L are around 14m. After replacing and welding the appropriate condenser, you can replace the filter, weld all the interfaces, weld the gauge valve on the process port and test the pressure again, and check whether there is leakage in all solder joints.

D-type refrigerator operation steps: first open the process port 1, discharge the residual gas, weld the return pipe 2 and weld the table valve on the return pipe; After welding the condenser pipe at 3 points, weld the table valve on the condenser pipe, cut off the 4-point capillary tube and weld the two disconnection points to death. Put both gauge valves under pressure, and if the pressure of the two gauge valves does not drop after 12 24 hours, weld a 3 4m condenser pipe between 5 and 3 o'clock of the condensing high-pressure port (remove the 3-point gauge valve first); Weld open 6 points to change the filter, cut the capillary weld and insert it into the filter 2cm welded, weld all the welds, weld the table valve on the process port, you can test the pressure again, check whether there is leakage in all the solder joints.

1 Refrigerators can be big and small. **Definitely not the same. In addition, the pipe is broken by low pressure or high pressure, this ** is not the same.

If the low pressure is broken, you have to dig the back repair, which is very troublesome. If the high pressure is broken, a condenser is attached to the back, which is relatively simple. All have to be pulled to the repair shop for repairs.

The cost is not low. Hundreds of dollars!

2 Look at whether it is high pressure or low pressure The unevenness is due to the leakage of the pipe next to the press This ** is different.

3 Generally, it is good to repair with a welding torch, but the repair cost is far more than repairing the copper pipe, because it is necessary to refill the refrigerant or something.

Hello! The rupture of the refrigeration pipe will directly cause the refrigerant leakage and cause the refrigerator to not refrigerate, because it is not certain whether your refrigerator has refrigerant leakage, it is recommended that you directly contact the brand customer service to identify and repair. At the same time, Meiling refrigerator also reminds you to remember to defrost and ice your refrigerator regularly.

It's a pleasure to serve you, thank you!

If there is no leakage, it doesn't matter, can refrigerate prove that it is not worn.

Just find a weld to repair the refrigerator, it won't cost much.

Now it can still be refrigerated, it means that your refrigerator is good, the tube is not broken, and the phenomenon of your refrigerator is turned off every once in a while to defrost, and then you turn on the power to use it after it is melted, so that it also saves electricity.

If the pipe is really broken, you can't get it right, call a professional maintenance personnel to repair it.

Troubleshooting the reasons why the refrigerator is not cooling:

1.When the refrigerator is not refrigerated, you should first check whether the connection of the power supply is normal, check whether the light in the refrigerator is normal, and you can also use an electric pen for further testing.

2.If the power connection is normal, you can monitor whether the compressor is working properly. The compressor emits a small motor vibration sound during normal operation.

When the high-pressure output buffer pipe in the compressor is broken, or the screw fixing the tube is loose, the high-pressure pipe is not exhausted, and the low-pressure pipe is not suctioned, so the compressor is running, but it is not refrigerated.

Solution: Open the casing, replace the buffer tube, or tighten the screws.

3.If the compressor can run normally, the next step is to check whether the refrigerant in the refrigeration system is used up: you can let the refrigerator run for 3-5 minutes, cut off the power supply, and listen to whether there is a sound of water flowing.

If there is no sound. This means that the refrigerant in the refrigeration system has been used up or is leaking. It could also be that the compressor is incapacitated.

Solution: If there is a system leakage, by finding the leakage part of the system, after welding repair, pressure test, and evacuation are qualified, add refrigerant to a certain amount, usually according to the evaporator is full of frost or the refrigerator reaches the rated temperature.

4.A blockage in the refrigerator capillary can also cause the refrigerator to not refrigerate. When the capillary tube in the refrigerator is blocked, the refrigerant cannot enter the evaporator to absorb heat and exert its effect, resulting in the temperature of the refrigerator remaining high.

Depending on the type of refrigerator, the refrigeration situation will also vary. If the refrigerator belongs to the intercooling type and there is no ice making failure, you can check whether the fan of the refrigerator is working normally: open the refrigerator refrigerator door, press and hold the button at the edge of the box mouth with your hand (this button controls the indoor lighting and stops the fan when the door is opened), check whether the fan is working, the fan does not work will also cause the refrigerator to not refrigerate.

Solution: The capillary or dryer is clogged, and the outlet is hot, so remove it to remove it! In addition, there are generally two types of household refrigerators: direct cooling and intercooling, which refers to the heat exchange between the evaporator (cooling pipe) and the freezing and refrigeration rooms to achieve the purpose of cooling; Intercooling means that the evaporator (cooling pipe) is separated from the freezing and refrigeration room, and the cold air is blown into the freezing and refrigeration room by a fan to achieve the purpose of cooling.

Thermal protection, starter, can have problems, causing the refrigerator to jump as soon as it starts.

Is there a problem with the compressor's overheating protection, causing it to stop after a run?

After-sales service**. It's broken.

The fridge doesn't refrigerate, but it restarts and cools for a while. And then it stopped, what's the problem?