How to quickly paste wall tiles

There is no good way to do this, the first requirement is that the quality of your exterior wall tiles should be good, mainly because of the specifications and flatness. The second is to find a professional, that is, the bricklayer, which is also said to be a lot of words, the skill of the bricklayer directly affects the effect of pasting. 1 practice makes perfect, 2 tools at hand, 3 in a good mood, 4 and beautiful women.

Specific collage method: If you haven't pasted it, it's best to find a platform, put the soaked tiles flat on the table, and the cement blended glue of the tiles can not be too thin or too dry, and pick up the cement with a gray knife, and the cement will not fall down It is very good. Then spread the cement on the tile, spread it all over the back of the tile, and the cement should not be paved too flat.

It is best to use a gray knife to make a concave and convex one, so that if the wall is uneven, the cement can be in place by itself when you are collage.

The correct method of tile paving: 1. When paving the tiles in the bathroom, the cement should be full and the amount of cement around the tiles should be about the same, so as to ensure that the tiles are firmly glued to the wall and will not appear hollow. 2. How to ensure that the tile is paved and smooth?

Experienced decorators will use a plastic hammer to beat the surrounding areas of the tiles to control the surface flatness of the tiles in time. Otherwise, it will be too late to adjust the cement when it is dry. If the paving of bathroom tiles is not adjusted in time, it will lead to uneven paving, the edge is slightly higher, and the shower room has to be "deformed"!

3. Tiles need to be tested to see if they are vertical, and the method is to carefully measure the verticality of each tile to ensure that all tiles are firmly sucked on the wall. If the decorator's craftsmanship is poor, the gap between the tiles will be large. 4. If you want the tiles to stick firmly to the wall, you must make the outer edge of the tile and the wall full of cement after the tile is pasted, so that the tile will be more firmly glued.

If the edge of the tile and the wall are definitely not filled with cement, it will cause a small piece of the edge of the tile to fall off if you accidentally touch it! 5. There are 4 details to pay attention to when paving bathroom tiles: (1) Experienced decorators generally use their fingers to wipe the caulk of tiles and window frames.

Because the texture of the general brush is too soft, it is difficult for the caulk to be completely brushed in. (2) If the balcony is also tiled, it is necessary to brush a thick layer of mud on the original exterior wall, so that the tiles can be glued more firmly. If you don't brush, the tiles will easily fall off.

3) Sometimes we will also find that the wall tiles are cracked, and the reason is in the tile drilling. (4) When you need to paste tiles on the wooden wall, it is best to fix the barbed wire on the wooden board first to increase the adhesion of the tiles.

Before applying tiles, we first soak the tiles in water, but before soaking in water, we must calculate how many tiles need to be used, only in this way that unnecessary tiles will not be wasted after the calculation.

Before tiling, the tile typesetting is done, and then the cement and sand are mixed according to the normal mixing ratio, and finally the construction tiles can be carried out on the wall and the ground. But before we paste tiles, we must first clean the wall or the ground, if there is putty or white ash on the wall, we must first remove the putty or white ash and then carry out the tiling process, do not do this direct tile will produce hollow drum or use a period of time for the tile to fall off.

Precautions for sticking wall tiles.

Before pasting the wall tiles, it is also necessary to pay off and arrange the bricks, so that the tiles are more neat after paving. It is generally recommended that the non-whole bricks should be arranged in the corners, and it is best not to have two rows of non-whole bricks on a wall, and it should be noted that the width of the non-whole bricks should not be less than one-third of the whole bricks. Otherwise, it will affect the aesthetics of the overall wall.

Before pasting wall tiles, it is necessary to determine the horizontal and vertical aspects, the joints should be straight, and the width of the gaps should be uniform. In case of pipelines, switches and other protrusions, it must be cut with whole bricks, and must not be pieced together with non-whole bricks. Do not pave the wall tiles to the top at one time to avoid falling and injuring people due to unstable paving.

The method of attaching wall tiles is as follows:

1. Before paving tiles, we must first know the characteristics of ceramic tiles, because there are many types of tiles, and the characteristics of each ceramic tile are different, and the treatment methods are also different. There are many tiles that need to be soaked in water, but there are also some that do not need to be soaked in water, or the time of soaking is different, so these must be clearly understood.

2. The ground should be treated before paving the tiles, and the ground should be smooth. Usually the tiles are glued with cement mixed with other things, so there must be a feeling of sticking when making cement, and the cement needs to use the 325 model to work very well.

3. Before laying the floor, the tiles are laid on the ground first, which can show a better effect, and you can also see how many tiles are needed, whether there is a place to cut, etc.

4. Experienced workers must be selected for tile paving, because they are very familiar with tile materials, and are very familiar with cement and other construction methods, and they can also buy cheap and first-class tiles for consultation, which not only saves money, but also ensures the quality of tile laying.

Precautions for sticking wall tiles.

1. Before pasting wall tiles, you need to see whether the grade, tile color and sample are the same when purchasing, if confirmed, try to let the person in charge of construction sign for it, otherwise notify the tile seller immediately.

2. If the wall is an untreated putty wall, the wall must be removed first. The wall tiles must not be less than one-third bricks.

3. Usually when paving high-grade wall tiles, it must be primed with cement mortar, and at the same time, the wall should also be brushed, and then paved with special wall tile paste.

4. The quality requirements for wall tiles used in paving are high to prevent the purchase of inferior wall tiles. Poor quality wall tiles will have defects, uneven wall tile splicing, etc. The selection of wall tiles should be based on the surface flatness, verticality and finish of the wall tiles.