What to do if the dial inside the watch is fogged into the water, and how to solve the water fog on

The dial of my watch is flooded and fogged up, in which case the watch must be taken to the repair department for re-repair and sealing.

It may be that there is a problem with the sealing strip at the back of your watch, you find a watch repairer, help you clean it up, and then replace it with a sealant strip.

Generally, when a water fogger enters the watch dial, we put the watch in a dry place and wait for it to dry naturally before continuing to use it.

Hello, this phenomenon occurs because the sealing performance is not very good, of course, only to disassemble it to dissipate the fog.

Hello, if the inside of the watch dial fogs up, it means that the watch is flooded, which requires disassembling the mechanical watch and cleaning the water

The inner dial of the watch can be placed for a few days with water mist, or put it in a rice jar to suck the moisture.

What should I do if water fogs up the inner disc of the watch? Go to the watch shop to repair the watch shop, you can open the shell and urge it.

The inner dial of the watch is fogged with water, so just dry the water droplets directly under the sun and dry the water droplets, or dry the water vapor, or blow it with a hair dryer to dry the water vapor inside.

Turn the watch over and wear it on your wrist and it will dry in a few days.

If there is moisture in the dial of the watch, it may be due to water ingress or moisture.

If the dial gets water and fogs, then you can blow it with a hair dryer and then it should dry out.

What should I do if the tag inside the watch is fogged up? This is a good solution, open the back cover of the watch, blow it with a household electric hot air, dry the water, and put some watch oil on the eyes. That's it, put on the back cover.

I recommend that you let it out in the sun, and if it's still foggy, it's best to go to a professional watch repair shop.

If the inner plate of the water meter is fogged up, you can take a hair dryer to see if it can be dried or disassembled and wiped.

You take this dial off again and blow it with a hair dryer to flush the water away.

If the inside of the watch is fogged up by water, be sure to send it to the place where the watch is repaired and the water inside will be cleaned out.

I can teach you a simple method, put the watch inside the rice after the watch gets into the water, and the sealing effect of the rice is very good for water absorption.

What should you do if the dial of the watch is flooded and fogged, so you can take off the dial and dry it with a hair dryer? Be careful not to get water all the time.

If the watch dial is flooded, it also means that you usually run into the water when you are representing, and you can choose to use a hair dryer to blow it or put it in a cool place to dry.

If the water is ingress, it needs to be repaired, and it is recommended to take it to the after-sales service for inspection in time.

If your watch is foggy, then you find the watch in the email, ask him to clean it for you, and then help you make it waterproof.

What should I do if the dial inside the watch is fogged up? Fog up the water on the dial and leave it in the sun for half an hour.

Hello friend, the water entering the inner disc of the watch should be placed under the sun to allow the water to evaporate.

Ah, what should I do if the inner disc of the watch is flooded and fogged? You can use a hair dryer to blow dry, or you can do a manufacturing contest in the sun, and you can fix this fogging after a few minutes.

If the dial inside the watch is flooded and fogged up, you still have to go to a special watch repair shop to open the back cover to deal with it.

Then if the mouse is in that issue, it is obvious that I go there, that is, the waterproof is not good, and you are looking for the watch shop or repair shop, let him help you clean it up.

If the dial inside the watch is fogged into the water, you must choose to go to a special repair shop for repair, or you can use a hair dryer to blow it.

There are several conditions for fog in the glass of the watch, (1) the watch is flooded, (2) the air humidity inside the watch is relatively large, and (3) the temperature difference between the watch and the outside world is relatively large.

The solution to the water mist on the watch is as follows:1.Wrap the table tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, and bake it under the light bulb for about 3 minutes to eliminate the water mist inside, but do not put it close to the light bulb or bake it directly, so as not to cause the surface to be deformed by heating.

2.Wear the surface inwards and the bottom case outwards on your wrist to remove the mist from the surface after a few hours.

3.If you have silicone, you can put the silicone and the watch in water into a closed container, and after a few hours, take the watch out again, and the water mist in the watch will disappear.

4.If the water ingress of the watch is serious, it is best to send it to a watch shop to wipe the oil and eliminate the water in the watch to avoid rust on the parts of the watch.

How to deal with water and fog in the watch:

1. When the watch enters the water and fog, the easiest way is to wear the watch on the wrist backwards, that is, let the watch reflect inwards and the bottom case of the watch outward. After a few hours, you will notice that there is less and less moisture inside the watch.

2. Prepare some paper towels or moisture-absorbing flannel, wrap the watch tightly, place it on a 40-watt light bulb about 5 cm, and bake it for about half an hour. After that, you will notice that the moisture in the movement slowly disappears.

3. It can also remove fog vapor by basking in the sun. First open the back cover of the watch, then wrap the watch completely with a paper towel or moisture-absorbing flannel cloth, and take it to the sun for most of the day to remove the moisture in the movement. If the watch is seriously flooded, it can be left for a longer time.

4. After the watch is flooded, you can open the back cover of the watch first, remove the battery, and use the hair dryer to aim at the watch in low gear. After blowing until it is completely dry, reattach the back cover. When installing, you can also check whether the sealing ring is aging and broken, and remember that the back cover must be fastened if it is in good condition.

5. Dry the granules with silica gel. Put the silicone granular substance in a closed container with the watch that has accumulated water, and after a few hours, remove the watch and the water will disappear. This method is simple and economical, and does not compromise the accuracy or longevity of the watch.

The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.