Solve the causes of dust on the dial of the watch and how to prevent it. 100

There are two main reasons why watches are dusty. First, you should first check whether your watch mask is tight, whether there are cracks due to aging or the whole is loose with the case (ring). Because the watch is not well sealed, it usually enters the water when it enters the dust.

The second reason is due to internal wear, as the ash on the dial does not come from the outside.

How long have you been wearing your watch? Usually, dust entering the watch dial gradually seeps in during long wear. If only fine dust is entered, it can be left alone without affecting the time of walking.

If there is a certain amount of dust entering the watch dial, you need to pay attention, because dust is very likely to cause the movement to jam and go inaccurately. If there is a lot of dust in the watch, it is recommended to do a comprehensive oil wash and maintenance of the watch.

Hello, glad to answer for you!

Dust entering the dial of a watch is usually due to gradual penetration during long-term wear, and if it is dust of a certain length such as hair or acrylic fibers that enters the dial, it is necessary to pay attention, and such dust is very likely to cause the movement to stop. Do not easily open the back cover for cleaning, and take the watch to a professional after-sales center for cleaning in time.

Daily maintenance of the dial:1. If the watch is flooded or damp for a long time, it is very easy to induce the discoloration of the dial, or the paint of the dial cover peels off, which is characterized by more occurrences at the edge of the dial. Therefore, when wearing a non-professional diver's watch, try not to get involved in rain, swimming, etc.

2. If the watch is placed for a long time or exposed to sunlight, all kinds of rays in the sunlight will make everything slowly change color, and the same is true for exquisite things, no one can escape. Expose your watch to the sun as little as possible.

After finding that the watch is dusty, you must not open the back cover to clean without professional guidance, you should find professional help or send it to a professional repair shop for cleaning in time, and you should regularly do waterproof testing and timekeeping accuracy testing to ensure its normal operation. If only fine dust is entered, there is no need to clean it without affecting the appearance and use.

If the watch hands are dirty, it is possible that the gears behind the watch are also dirty, and the dirt will cause errors when the watch runs the seconds, so it will take a few months to re-align the time. It is recommended to send it to a maintenance point to clean it up and see if the seal of the watch is aging, causing dirt to go in.

Do-it-yourself ways to remove dust:

1. There is a circle of evenly arranged grooves on the edge of the cover on the back of the watch, which needs to be snapped on with a special tool to unscrew the cover. However, you can use scissors and rotate counterclockwise to unscrew the cap.

2. Then you can scrub it with a cloth dipped in water, and all the dust inside will come out, and finally you can install the case back on.

Dust that enters the dial of a watch is usually due to gradual penetration over long periods of wear. If it is just a fine gray dust, without affecting the appearance and use, there is no need to clean it. However, if it is a certain length of dust such as hair or acrylic fibers that enters the dial of the watch, it is necessary to pay attention, because such dust is very likely to cause the movement to stop.

If you have any questions, please click on the avatar to consult**, welcome to call.

You should first check whether your watch mask is tight, whether there are cracks due to aging or the whole is loose from the case (ring).

Bad quality is sure, but there are two reasons:

1. The watch is not well closed, and usually water enters when it enters the ash.

2. The ash on the dial does not come from the outside world, but is caused by internal wear.

The quality of the table is not good, there are gaps white, and the explanation is no longer waterproof.

Watch anti-dust protection and ash handling methods.

1.If the watch only gets into fine dust, we don't need to clean it up without affecting the beauty and use of the watch. However, if it is hair or acrylic fibers and other dust of a certain length that enters the watch dial, it needs to attract our attention, because such dust is very likely to affect the operation of the watch movement or even damage the movement.

2.When we find that the watch is dusty, do not easily open the back cover of the watch for cleaning, and send it to the maintenance and after-sales center for cleaning in time, and regularly do waterproof tests and timekeeping accuracy tests to ensure its normal operation.

3.At the same time, we should also pay attention to the watch in our daily life not to come into contact with chemicals. The waterproof watch is not cold water or hot water, so don't wear it to take a bath, avoid water vapor to ensure its waterproof effect, and then after adjusting the watch, remember to restore the watch handle and press it tightly to avoid dust entering.

1.The easiest way to do this is to spend some money and ask someone to fix your watch to clean it for you. It's hard to say the price.

2.Do it yourself, if there is a circle of evenly arranged grooves on the edge of the cover on the back of the watch, you need to use a special tool to snap on the cover to unscrew it, but you can use scissors (fork the scissors and use the two tips to jam the two grooves diagonally respectively), turn it counterclockwise, you can unscrew the cover, and you should be careful to scratch the cover when twisting.

If there are no grooves and only a raised polygon, you can find a vise with a large opening mouth (flat-headed), clamp the two opposite sides of the polygon (the pliers should not be clamped upside down, but the cover should be vertical), rotate counterclockwise, and be equally careful to scratch the cover.

If there is nothing and the light is abrupt, this is the best thing to do, and it will be opened with a few pries with a knife from the gap in the edge. (Be careful to pry a few more times from different locations around the lid and not grab one spot.) )

If it is a mechanical watch, after opening the back cover, you must first pry off the dial knob on the outside with a flat-neck screwdriver, so that you can take out the movement inside (the electronic watch is saved, and the contents will all come out with a direct knock), and then gently wipe off the dust inside the watch case with a soft cloth.

The way to put it back is how to disassemble it.

The maintenance interval of a watch should generally depend on its natural rate of wear and tear, but another important factor depends on the daily use of the watch and the environment in which it is worn. It is recommended to come to the service center every year to test the waterproof performance of the watch, and carry out comprehensive maintenance and maintenance every 2-3 years.

If there are dust particles at the factory, this may happen if you are cautious, after all, the dust-free workshop cannot be 100% guaranteed to be completely dust-free during assembly. As for the hail when in use, it is unlikely that the current brand Ruibiao will be made in terms of production process and product quality, and it is recommended to go to the after-sales service to test the tightness.

A watch, or wristwatch, is an instrument worn on the wrist to keep time or display time. Watches are usually made of leather, rubber, nylon cloth, stainless steel and other materials to make a strap, and the watch head that shows the time is tied to the wrist.

There is no absolute seal.

What are the types of dust floating in the air?

1.Soft dust, composed of carbon particles.

2.Hard dust, composed of hard quartz particles.

3.The human body is composed of scalp finger genera and hair.

4.Man-made fibers, which are produced by industrial products such as sweaters, ropes, paper, etc.

In addition to the dust-free workshop, there will be the possibility of the above dust re-entering during operation, even if the current well-sealed diver's watches of various brands still can't stop several types of dust around us at all times. It is necessary to know that there is no absolute seal, for objects moving in the air, it has the adsorption force of the surrounding dust, if you have the opportunity to open a "3 prevention" watch that has never been opened, you will find that there is dust inexplicably entered, around the sealing ring, there will be a circle of dust.

With the exception of hard quartz particles, which caused slightly more damage to the movement, the industrial fibers only blocked the transmission of weak power, but did not cause substantial damage to the internal components. Even if a 0 2 mm diameter Sunny fiber enters the movement, the movement will come to a standstill, but the internal parts will not be deformed. At this point, the movement can still be restored to its original state as long as it is properly disassembled.

It is caused by a poor seal.

The back cover of the watch should always be able to be opened.

Give the money and ask someone to help you solve it, or buy a new one