Forklift uphill fixed point parking steps, forklift uphill downhill operation points are those

To stop at a fixed point uphill, first depress the clutch.

pedal, then press the brake pedal.

Hand brake is required for starting. The specific steps are as follows:

<>4. Pull up the handbrake.

To stop at a fixed point uphill, first step on the ruler clutch.

pedal, and then pressed the brake pedal after Qin was sleepy.

Hand brake is required for starting. The specific steps are as follows:

<>4. Pull up the handbrake.

Summary. The requirements for the uphill operation of the forklift truck are: 1. When starting on the ramp, the start should be stable and the engine should not be turned off. 2. The forklift cannot slide down, and the wheels cannot be idle. 3. Do not make a sound when changing gears.

The requirements for the uphill operation of the forklift are: 1. When the ramp starts to inspect and shoot, the starting is flat and stable, and the motivation for failure and envy must not be turned off. 2. The forklift cannot slide down, and the wheels cannot be idle. 3. Do not make a sound when changing gears.

The requirements for the downhill operation of the forklift are: 1. The belt spike should be driven backwards to prevent the goods from falling upside down. 2. It is strictly forbidden to turn off the ignition and slide.

3. When the load is driving at a speed of more than 7 degrees and going up and down the slope at a speed higher than the first gear, the brake shall not be used unless there are special circumstances. Before operation: check the appearance, fill with fuel, lubricating oil and cooling water.

Check starting, operation and braking performance. Check whether the lighting and sound signals are complete and effective. During the operation of the forklift, check whether the pressure and temperature are normal.

After the forklift is operated, the external leakage should also be checked and the seals should be replaced in time. When starting: Before starting, observe the surroundings to confirm that there are no obstacles that hinder driving safety, and then sound the horn before starting.

For pneumatically pneumated vehicles, the brake pressure gauge must reach the specified value before starting. When the forklift starts with loads, the driver should first confirm that the goods carried are stable and reliable. Start slowly and steadily.

Extended information: Matters to be paid attention to when driving a forklift: 1. Check the control and alarm devices before driving, and operate them after repair if they are found to be damaged or defective; 2. When handling, the sail should not be carried over the specified load, the fork must be inserted under the goods, and the goods are evenly placed on the forks, and the goods are not allowed to pick the goods with a single fork tip; 3. Start, steering, driving, braking and stop smoothly, and slow down when steering on wet or slippery roads; The goods should be lowered and the mast should be tilted backwards; 4. The ramp should be driven carefully, when more than one-tenth of the ramp is driving, the uphill slope should be driven forward, the downhill should be driven backwards, the uphill and downhill should not be steered, and the forklift should not be loaded and unloaded when driving; 5. When driving, you should pay attention to pedestrians, obstacles and potholes, and pay attention to the gap above the forklift; 6. No one is allowed to stand on the fork, and no one is allowed to carry people on the car; No one is allowed to stand under the fork or walk under the fork; It is forbidden to operate the vehicle and attachments from a position other than the driver's seat; Do not move goods that are not fixed or loosely stacked, and be careful to handle goods with larger dimensions; 7. The high gantry forklift with a lifting height of more than 3 meters should pay attention to the falling of the goods above, and protective measures should be taken if necessary; When working, the mast should be tilted backward as much as possible, and tilted forward and backward within the minimum range; References:

Encyclopedia - Forklifts.

I hope I can help you with my balance, and I hope you can give me a thumbs up, your evaluation is very important to me, thank you, I wish you a happy life, a lot of money, and good luck. 

You can step on the clutch first, then eat into the gear and then refuel, slowly release the clutch, feel the pour-down point, and release the handbrake. The point will not be returned. There can also be a brake first, then the handbrake is released, then the clutch is stepped on, the gear is suspended, and then half a foot is used to step on the accelerator, and then slowly release the clutch, and it feels like the brake is loosened.

Pay attention to the throttle can be added a little more, otherwise it will be easy to stall!

Answer 1: First of all, when you stop, pull the handbrake. 2. Step on the clutch and put it in gear. 3. Slowly lift the clutch, feel the car shake slightly, that is, the clutch has just been combined with the feeling, your own feeling.

4. At this time, let go of the handbrake, and the car will start at this time.

The requirements for the uphill operation of the forklift are: when starting on the ramp, the start is stable, and the engine must not be turned off. The forklift cannot slide and the wheels cannot be idled. Do not make a sound when changing gears.

The requirements for forklift uphill operation are: 1. When starting on the ramp, the start should be stable and the engine should not be turned off. 2. The forklift cannot slide down, and the wheels cannot be idle. 3. Do not make a sound when changing gears.