I can t install the graphics card. Ask the master for help!! Thank you.

Is it a problem with the graphics card?

Tell us about the system you are using and the version of the driver you are installing (if you don't know, you can also talk about the file name).

Pay attention to whether the motherboard supports the graphics card.

Super Bunny's "Drive Angel" automatically detects the model and installs the driver.

Graphics card failure, repair method.

Fault 1: The discrete graphics card may cause bad contact with the slot, or the interface between the discrete graphics card and the monitor may be in poor contact. As a result, discrete graphics cards do not work properly.

The manifestation of the former fault is that after booting, the computer has a black screen or an alarm prompt. The latter malfunction manifests itself in the form of:

The screen display is not normal.

Repair method: 1. First of all, we have to check the slot of the independent graphics card, dust or granular stains will cause the phenomenon of graphics card failure. We need to use a dry rag to gently wipe the graphics card.

2. Secondly, we need the fixed bezel of the graphics card and the loosening of the screws, if the baffle is deformed, it should be replaced immediately. If the screw is loose, use a screwdriver to tighten it.

3. Finally, we need to check the VGA interface, if there is any undesirable phenomenon, the screen will have image tearing and color cheating. We only need to use the "replacement method" to make simple repairs.

Fault 2: The graphics card is incompatible with the motherboard. The reason for this is that the driver is installed incorrectly, so there is a bug, and in the case of incorrect settings, it can also cause a malfunction.

Repair method: 1. Replace other models of discrete graphics cards, load the driver, and shut down the computer to solve the problem. If the problem of the graphics card failure has not been officially resolved, we need to restore the registry or reinstall the computer system to solve the problem.

2. If the screen of the computer can be seen clearly, I don't need to use the method of the first step, I only need to delete the driver of the graphics card, and then install it correctly to solve the problem. If the handwriting is unclear when we enter the system again, we need to restart the computer, then switch to the safe mode of the computer, and set the handwriting in the desktop properties to solve the problem.

It's normal for the graphics card to be broken.,You can replace it.,When you change a good one, you can make sure that it's not over-warranted.。

The over-insured, the high-value ones are taken to repair, and the repair shops with a general value of more than 400 will take over the worthless, and they will be tossed as a dead horse, such as a hair dryer blowing down the core and video memory.

I've also encountered this situation, I don't know if yours will be the same as me, I removed the graphics card, put it in the sun and exposed it to the sun for a morning, and after installing it, okay, you can try. Well, remember to give extra points.

Judging from your description, it's a problem with the graphics card, wipe off the gold finger of the graphics card and try it, pay attention to see if the fan of the radiator is too dusty and stuck, or the speed is abnormal, and see if there is a problem with the power supply of the independent graphics card.

Just install the driver correctly and then refresh it in Device Manager.

-1. Install the graphics card.

Before installing the graphics card, it is also important to note that the graphics card is composed of many precision integrated circuits and other components, which are easily affected by static electricity and lost, so make the following preparations before installation.

Turn off the power of your computer and unplug it.

When taking the graphics card, please avoid the metal wiring part as much as possible, and wear anti-static gloves when assembled.

When you unplug the ATX power outlet from the motherboard, make sure the power switch is off.

Installing a graphics card can be divided into two parts: hardware installation and driver installation. Hardware installation is to properly install the graphics card into the graphics card slot on the motherboard, and the main point to grasp is to pay attention to the type of agp slot (AGP

The development of the interface has gone through the stages of AGP1X 2X Pro 4X 8X, etc., and its transmission speed has also developed from the bandwidth of the earliest AGP1X of 266MHz S to the bandwidth of AGP8X.

2GB Pro and other graphics card slots are not the same, the graphics card specification slots in the back can generally be compatible with the front graphics card specification slots, for example, the graphics card slots of the AGP4X specification can use AGP2X graphics cards, and.

AGP4X graphics cards will not work properly on AGP2X graphics card slots. ）。Secondly, be sure to turn off the power when installing the graphics card, and take care to install the graphics card in place.

Netizen stickers. The first step is to remove the expansion bezel and screws on the corresponding AGP slot from the rear shell of the chassis.

The second step is to carefully align the graphics card with the AGP slot and insert it into the AGP slot very reliably. Note: Make sure that the metal contacts of the gold finger on the card are in good contact with the AGP slot.

The third step is to lock the screws with a detergent so that the graphics card is firmly fixed on the chassis.

Step 4: Plug the 15-pin pin VGA cable plug on the monitor into the VGA output plug of the graphics card.

The last step is to turn on the power again after confirming that it is correct, and complete the hardware installation of the graphics card.

2. Install the sound card.

List of main interfaces:

There are a lot of interfaces on the sound card, so let's give you a brief introduction to them.

Netizen stickers. The first step is to find a spare PCI slot and remove the expansion baffle and screws on the corresponding PCI slot from the rear case of the chassis.

The second step is to carefully align the sound card with the PCI slot and insert it into the PCI slot very reliably. Note: Make sure that the metal contacts of the gold finger on the card are in good contact with the PCI slot.

The third step is to lock the screws with a knife to ensure that the sound card is firmly fixed on the chassis housing.

Step 4: After confirming that everything is correct, turn on the power again to complete the hardware installation of the sound card.

3. Install the network card.

The installation of the network card is also very simple.

Netizen stickers. Make sure that the power supply of the chassis is turned off, insert the network card into a free expansion slot of the chassis, and make sure to align it with the slot when plugging it in. Insert the network card into the slot with the big fingers of both hands, and be sure to insert the network card tightly; Attach the screws and tighten them; Finally, connect the crystal head on the finished network cable to the RJ45 interface of the network card.

The design of the computer is a little good.

It's just that the wrong thing can't be plugged in.

As soon as you put the graphics card.

on the motherboard of this computer.

It's a big square board.

on the slot. Plug in the hole when you find it.

When will it be plugged in?

That's right. In fact, motherboards have manuals.

It says last to go.

Drive the house of the next related drive.

If you don't know the model.

Next Driver Genie.

over~

If you are a brand machine.

Please find a local ** businessman.

If it's an assembly machine.

Just install a ghost system and it's OK.。

Comes with any drive.

It's very convenient that Ghost is sold in any computer city.

A few bucks a copy.

It's a pure fool-proof system.

Method 1. 1. First, right-click (computer) and click (Properties). Sakura Ming.

2. Find (Device Manager) on the left side of the display page, then select the display card at the bottom of the right border, right-click the display card bar, and then click (Update Driver).

4The driver will be installed automatically until the Hardware Update Complete Wizard box is displayed. Click (Done). This is the end of the update.

Method two. 1.The above method is more cumbersome, and it is very convenient to update the driver by using the driver wizard software. First, open the installed Driver Wizard program.

2.In the Driver Wizard interface, the program will automatically connect to the network to check whether all drivers of the machine are missing and available updates. After checking the available update graphics card driver item that shows up in Morning Song, click (Upgrade).

4.At this time, the installer interface will pop up to install it accordingly. Finally, click (Done) and restart your computer to update the graphics card driver.

Drive the elf, drive the life, Master Lu, try it all once.

Fault: The graphics card driver failed to be installed.

Symptom: When installing the graphics card driver, the message fails, and it is impossible to change to a different version of the driver.

Settle. Solution: To install the graphics card driver correctly, you can follow the following methods:

First, on startup, press '

del" key to enter the BIOS

Settings, find it.

chipset features

setup option to be inside.

assign irq to vga

Set to. enable

Then Paul. Deposit and exit. A lot of graphics cards, especially.

matorx

when this is set to.

disable

The driver is generally not installed correctly. Also, for the ati

graphics card, first of all, the graphics card.

Set to standard.

VGA graphics card, then install the included driver.

Patch the motherboard in one first! Try it!

You shouldn't have inserted an N card.