How to route wiring in a ceiling that has been suspended

The method of wiring in the ceiling of the suspended ceiling is as follows:

Divide the space in the ceiling into several cells and lay high-capacity cables. From the junction room by means of pipe through or directly laid to each partition center, by the partition center of the district to lead the cable through the wall or column to the communication lead-out, can also be set in the center of the adapter, the large-capacity cable is divided into a plurality of small cables and then to the communication lead-out end.

The ceiling is the place where the top surface of a building's interior is located. In interior design, the ceiling can be painted, painted to beautify the indoor environment, and install chandeliers, fluorescent pipes, ceiling fans, open skylights, and install air conditioners to change the effect of indoor lighting and air circulation. In the past, straw mats, reed mats, and wooden planks were the main materials used in traditional houses.

Do you do latex paint? If there are not many lines, you can consider opening a small hole and wearing it slowly, but it will definitely not work if you have more? It seems that the repair is not professional.

The three-phase a, b, and c of the main circuit power supply are yellow, green, and red respectively; The control circuit wire is generally specified as the AC main circuit - black; AC control loop - red; DC--Blue; Zero line - white; Cabinet external interlocking wire - orange or yellow; Protection (grounding) wires - yellow and green two-color, etc.

When wiring, it is generally horizontal and vertical, depending on personal aesthetic ability and experience.

Open a manhole, and people go up. If people can't go up, open a few small holes to cross the line.

Yes. If the wires are buried in the ground, they should be covered with floor tiles, both to hide and to protect. However, if the wire is permanent, there will definitely be a problem, so it needs to be repaired.

Therefore, it is necessary to lift the floor tiles, if the home is laid with wooden planks, it is not too troublesome, but if it is a tile, the amount of construction is very large, and you may have to lift the tiles and wooden boards one by one to find out where the fault is. This is tantamount to a second decoration.

Then arrange the wires on the ceiling, save money and look beautiful. Compared with burying in the ground, the advantage of wires going to the ceiling is that you don't need to groove in the ground, and there are more grooves in the home, which can easily lead to the instability of the wall structure. Hiding wires in ceilings or suspended ceilings not only saves you the hassle of floor slotting, but also saves a lot of money.

This practice is not allowed by any norm. Theoretically speaking, PVC is flame retardant, once the wire **, then PVC flame retardant pipe can prevent the fire from continuing to expand, because PVC is not easy to burn We analyze your room hazards from two points.

1. Assuming that your room is newly renovated, then there will be two lines of defense for the fire caused by short circuit or overload, the circuit breaker and the insulating skin of the wire, unless your circuit breaker specification is wrong or unqualified and the wire is a substandard product, the fire in your home may not be able to be stopped! From this point of view, the incidence of fires in new homes is lower.

2. Assuming that your room has been more than five years, then the circuit breaker may fail, the aging wire may not reach the rated load and the insulating skin can not be flame retardant, so the probability of fire in the room at this time is greatly increased, it is recommended to replace the circuit breaker, or if you have money, then redecorate and change the line, remember to wear the pipe.

In fact, there is no need for a sleeve, and the terminal head is wrapped with insulating tape.

Yes, insulated conduit is used where the wiring is placed.

Home reed mill court decoration hanging ceiling to combine the floor height, decoration style and decoration budget considerations, if the ceiling can hide the wires, more beautiful, but some floor height is relatively short or small apartment is not suitable for the ceiling do not reluctant,How to line the ceiling without hanging the ceiling? What are the precautions for not taking the dark line on the ceiling? Let's find out!

How to line the ceiling without hanging the ceiling

1. Routing planning

Workers did not arrange the power supply in the early stage of construction, resulting in the opening lamp after the ceiling can not find the line, so it is necessary to pay attention to the position of the line arrangement, which requires the combination of electrician and carpenter. Some holes are not accurate when excavating, resulting in inconsistent sizes or spacing. The depth of the light hole is due to the height of the ceiling, and this depth should be able to be placed in the spotlight.

If it is not enough, it will not be installed.

2. Ground wire dark wire

The ground line is covered with floor tiles. It can also be covered with concrete, flattened and then installed with wooden floors. Generally, it cannot be slotted, otherwise it will affect the floor structure and have potential safety hazards. The dark line of the wall line is generally slotted and installed with the dark line.

3. The top line is dark

The dark line of the top line covers the cable with the ceiling, and the dark line is installed with a small slot if the ceiling is not suspended, and the corners are covered with gypsum wire The cable is also very beautiful, and the space is larger and contained, and there is no sense of depression.

What are the precautions for not taking the dark line on the ceiling?

1. Install the corner line, when the tile is pasted, the supporting corner line of the integrated ceiling is tightly fixed to the tile in the horizontal case, so that there is no obvious gap.

2. The distance between the boom and the keel should be one to the size of the panel.

3. Route the line at the top, determine which positions need to install lamps and lanterns, and which positions need to install kitchen and bathroom appliances, and arrange the lines in advance.

4. The buckle panel directly affects the overall effect of the ceiling. Not only should it be flat, but it should also be sewn straight.

5. When installing (embedding) electrical appliances, the interface between the panel and the electrical appliances should be smooth and seamless.

How to line the ceiling without hanging the ceilingWhat are the precautions for walking the dark line without talking about the pure top

The ceiling installation is divided into five steps, which are to determine the ceiling height, boom installation, installation keel, decorative board installation, and ceiling lighting installation.

Tools: screws, screws, nuts.

1. Determine the height of the ceiling before installation.

The edge line of the ceiling is a line located on the rock wall of the whole ceiling, fixed on the walls around the ceiling, and the height and levelness of the entire ceiling are determined by this edgeline.

2. Boom installation.

The so-called boom refers to the davit installed perpendicular to the ceiling, the light steel keel generally adopts the screw, and the wooden ceiling is a vertical wooden pole.

3. Install the keel.

After the boom is installed, it is to install the keel, the keel has transverse and longitudinal, the longer one is called the main keel, the short one is called the auxiliary keel, the main and auxiliary keels are vertically crossed, and the hanging wire is fixedly connected to form a lattice network.

4. Decorative plate installation.

The decorative board of the ceiling is also the ceiling that we can see, and there are many kinds of materials, and the gypsum board ceiling and the buckle tung board ceiling are used more at present. Then this decorative board refers to gypsum board and gusset board.

5. Ceiling lighting installation.

According to the above four steps, the ceiling is basically completed, and then according to the actual needs to install the lighting on the ceiling, the lighting on the ceiling is embedded and installed on the ceiling, the ceiling of gypsum board needs to be installed after the opening, and the gusset can be removed part of the gusset for embedded installation. At this point, the entire ceiling is installed.

Precautions for ceiling installation

1. Choose different types of ceilings in different areas.

2. Don't hang the ceiling too low.

3. The hidden pipelines and cable quality inside the ceiling.

4. Pay attention to the stability of Tongzhong Yu, and follow the steps step by step.

In the installation process, the first thing to confirm is to confirm the size used, and after doing a good job of measurement, the tightness of the ceiling can be guaranteed, and the stability is higher. When installing, the data should be measured in the part of the wall that is high, and marked with a wipeable pen, and fixed with a fixed line twice on the wall.

Then make a fix with cement nails and the wall. Next, the actual size of the ceiling is measured, and after the plate is installed, it is fixed, and the part that needs to be bent after death can be directly inserted into the previous plate.

Finally, after the PVC gusset is installed twice and sealed with the side pressure strip, it is completely completed.

Many owners are doing renovation work for the first time and are not familiar with many of the construction steps. Suspended ceilings are the finishing of home décor. If it is not installed, it may affect your aesthetics and safety issues in the future.

How to install ceilings in indoor suspended ceilings? For everyone who has a tutorial on setting the ceiling, the following is a guide for friends to learn about the indoor ceiling tutorial.

1. First of all, the indoor ceiling tutorial is that before preparing the ceiling for installation on the ceiling construction, it is necessary to ensure that the ceiling installation materials and tools are complete, the installation pipeline is clearly installed, and the structural dimensions are consistent with the preliminary design drawings.

2, smallpox base**;

Always inspect the ceiling before installing it, and if the quality of the fruit does not meet the building requirements, immediate action must be taken. This is a protective measure for the indoor ceiling tutorial.

3. Go online on the ceiling.

Ceiling height lines and keels are marked separately. Elevation can be used to show the position of the ceiling plane in the water column, and the height line pops up based on the position. The position of the keel is set according to the size of the plywood and the position of the keel.

For ease of installation, it is recommended to set the centerline spacing of the plywood size to about 2 mm. When carrying out keel placement, ensure the uniformity and integrity of the keel compartment, so that the ceiling has a more regular decorative effect. First of all, according to the principle of keel arrangement, the ceiling area on the drawing is scaled and the ceiling keel is arranged on paper.

Once you've decided on a location, place it on the wall. This part is also mainly used in the interior ceiling tutorial.

4. Fixed pontoons.

The suspension is usually held in place by expansion screws or nails, and the keel hook is fixed to the suspension with galvanized steel wire through a hole in the angle steel block. We recommend using telescopic boom material for the suspension. The type of telescopic boom is further diversified, usually with the No. 8 conductor straightened and the two conductors connected by a spring steel plate with holes.

Adjustment and fixing are mainly made of spring steel. This is also one of the tutorials for indoor suspended ceilings.

5. Please install the keel.

The keel has a main keel. Keel spacing can be measured using a die gauge. Each main keel is lifted first, and then temporarily fixed above the elevation line.

If the ceiling area is slightly larger, it is advisable to roll up several sections. Then, an auxiliary keel is installed between the main chain keels called the horizontal keel. Measure the length using a mold gauge and install it manually.

This is the main part of the indoor ceiling tutorial.

You can get it for free