Solid wood baseboard into the wall construction steps, how to install solid wood baseboard?

The steps to install the solid wood baseboard are as follows:

First, preliminary preparation. Before installation, we should measure the length of the baseboard that needs to be used at each stage.

Second, material preparation. After determining the length of the baseboard to be used with a tape measure, pencil, or other crafting tool, use a tool such as a sawtooth to cut the baseboard material.

Third, drilling. Before drilling, it is necessary to observe the wiring direction of the hydropower to prevent errors. The interval between the drilled holes should not be too large, otherwise it will be difficult for the solid wood baseboard to stick to the wall.

Special tools must be used to drill holes in the wall. In order to fix the baseboard more firmly, the interval of the drilled holes should be about 40cm, and the interval at the solid wood interface should be smaller. Nail small sticks of wood into the hole you have just drilled.

The nails that hold the baseboard in place need to be nailed to this heel strip, and if they are nailed directly to the wall, the nails will easily loosen.

Fourth, fixation. Before fixing the baseboard, you need to level and clean the wall, otherwise after the solid wood baseboard is installed, there will be an embarrassing phenomenon that it cannot fully fit the wall, which will leave an unsightly gap. Therefore, we need to look at the position of the drilled hole, and then fix the nail to the baseboard.

When fixing, pay attention to whether the baseboard is close to the wall, and the nail should also be completely submerged in the baseboard.

Fifth, corner processing. The solid wood baseboard at the corner of the wall is generally cut by the method of cutting, and the edge of the corner is cut to 45 degrees, and then fixed by assembling and fixing. The result is a beautiful baseboard in the corners.

It can be embedded in the wall (commonly known as dark baseboard), which is a more traditional and practical construction process.

The baseboard has 3 positive and 2 negative effects:

First, the decorative role;

2. Protective role;

3. Easy to clean;

Fourth, the first negative effect is related to the construction practice: the open baseboard will block the furniture against the wall and will accumulate dust on the top; The dark baseboard solves this problem, and the furniture can also be placed really against the wall, without leaving a gap in the back, and there is no dust on the top surface of the baseboard.

Fifth, the second negative effect is that the cost of dark kicking will be much more expensive, because.

The dark baseboard project is complex, and it is necessary to straighten the groove, remove the plastering layer smoothly, and the paving and embedding operation is relatively laborious.

The specific method is: it is necessary to chisel off the plastering layer thicker than 2cm at the root of the rough wall (about 15 cm above the ground), then stick the floor tiles or floor, and finally paste the baseboard.

Note that the surface of the dark baseboard protrudes 5mm above the blank wall, because the interface between the two materials on a plane will crack and is not easy to straighten.

The dark baseboard does not affect the load-bearing of the wall, as it only chiseles off the plastering layer and does not damage the main structure.

With the increase of labor costs, the dark baseboard has a tendency to gradually decrease, and most of the open baseboards are used.

The types of baseboards are: ceramic, glass, stone, solid wood, imitation solid wood, MDF, PVC, aluminum alloy, PS polymer, glass, stainless steel, etc.

Baseboard selection:

1. The material is selected according to the ground material, for example, the baseboard selected for the solid wood floor is the solid wood baseboard.

2. There are 2 ways to choose colors:

1) According to the color of the floor, it should be close to the color of the floor and slightly darker than the color of the floor, and beautiful, generous and practical and easy to clean. This method is suitable for most users. It can also be very different from the floor, and there will be unexpected effects.

2) According to the color of the door sleeve line, this method can make the whole room have a consistent tone. The color of the door cover line is the same or close to the color of the door, and the color of the door is the main color of a room.

3. It is worth mentioning that the width of the baseboard is also particular, and the baseboard should be selected according to the height of the entire room, and the general family can choose 10cm.

One is to smash the cement mortar stucco layer to give up the thickness of the baseboard; One is to construct on the wall of light steel keel, and the gypsum board should not be installed to the bottom, and the position of the baseboard should also be left. However, although it is said to be "the same flat", in order to make the wallpaper have a "foothold" - closing, the baseboard cannot be made exactly the same flat, and it is definitely necessary to leave a little bit (even if it is only 3 mm), otherwise, the wallpaper cannot be closed - unless the wallpaper is directly pasted on top of the baseboard like a sticker.

The above is from the team "I Know About Decoration".

If you are satisfied, please click "Select Satisfied" below me, thank you!

Solid wood baseboard installation method:

1. The length of the baseboard is fixed, and the length of the baseboard that needs to be used in each block is different, so the length of the baseboard that needs to be used in each section needs to be measured first.

2. After determining the required length of the baseboard with a ruler and pencil, use a sawtooth and other tools to cut the baseboard material.

3. Observe the wiring direction of hydropower before drilling to prevent errors. The interval between the drilled holes should not be too large, otherwise it will be difficult for the baseboard to stick to the wall. Use special tools to drill holes in the wall.

The common length of the baseboard is 2m, in order to fix the baseboard more firmly, the interval of the drilled holes should be about 40cm, and the interval at the interface should be smaller.

4. Nail a small wooden strip into the hole you just made. The nails that hold the baseboard are nailed to this wooden strip and directly to the wall, and the nails are easy to loosen. Note:

for the pipes of hydropower projects. Buried in the wall, directly below the switch socket is the position of the pipe, and the position should be calculated when punching the hole to avoid damage.

5. Before fixing the baseboard, the wall should be leveled and cleaned, otherwise after the baseboard is installed, it cannot be completely attached to the wall, leaving unsightly gaps. Look for the position of the drilled hole and secure the nail to the baseboard.

6. The baseboard at the corner of the wall is generally cut by the cutting method, and the edge of the corner is cut into a 45-degree angle and then flattened and fixed. The result is a natural and beautiful baseboard in the corners.

First, the material of the bright baseboard.

1. Tile baseboard.

The tile material is relatively light and thin, and it will be too heavy or heavy when attached to the wall. Ceramic tile styles are abundant, patterns and patterns are numerous, no matter which decoration style you choose, you can choose a more suitable tile matching, so that the space is more harmonious, the wall also has a three-dimensional sense, and the decoration is more graded.

2. Wooden baseboard.

Wooden baseboards are more suitable for wooden flooring. Wood is divided into solid wood material and MDF, and the baseboard of solid wood material is more expensive. The wooden baseboard gives a softer feeling, a warm, comfortable and warm space, and at the same time gives a natural and simple feeling.

Second, the baseboard color matching method.

1. The same wall color.

The bright baseboard is the same color as the wall, which improves the visual height of the wall, such as the floor is not high, the bright baseboard is the same color as the wall, the feeling of height extension, and the wall color is solid color design.

2. The same ground color.

The bright baseboard is the same color as the ground, and the ground and the bright baseboard are integrated, giving people the feeling that the ground is wider and the space is larger, which is more suitable for the design of small spaces.

3. The bright baseboard is lighter than the ground color.

The bright baseboard is the same as the color of the ground, but it is lighter than the color of the ground, which makes the wall and the ground more three-dimensional and layered, which is also a more common design method.

4. Versatile colors.

If you don't know which bright baseboard color is suitable, you can also choose a versatile color, such as a white bright baseboard, no matter what kind of tile, what kind of wooden floor or any kind of decoration style, it can be cleverly integrated into the design, will not affect the overall decorative effect, give people a more refreshing and comfortable feeling, but also to avoid color matching conflicts.

Generally, there are two kinds, one is to fix the nail on the wall with steel nails or cement nails, this method needs to pay attention to the nail must be nailed in the groove of the baseboard, and after the nail is completed, the nail head or nail hole is repaired with the prepared paint putty, so as not to affect the appearance. The other is to glue it to the wall with silicone or strong all-purpose adhesive. Generally speaking, the former one is more commonly used and durable, and the latter mainly depends on the specific baseboard style or wall material selection.

For example, if the baseboard has no grooves, you can use glue for fear that there are nail holes that are not good-looking, but it will still open after a long time.

Generally, holes are punched in the wall, wooden wedges are driven into the holes, and then nails are nailed on, and my house is installed like this.

Don't use nails, just use glue, in this case, the glue smell is heavy, and the formaldehyde exceeds the standard.

There are also metal bayonet parts, which can be found by a skilled carpenter to help you design and install.

When I was decorating my home, I also learned about the installation method of baseboards, and played glass glue; Advantages: Easy to install, disadvantages: glass glue contains formaldehyde, smell, and will fall off and nail after a long time; Advantages: Quick installation, no pollution, disadvantages: The baseboard has nail holes, and the nails are easy to rust, which affects the aesthetics;

card slot installation; The advantages are beautiful, no pollution, the disadvantages are high, the baseboard needs to be customized, and the installation is troublesome;

Today I would like to introduce to you the installation method of my home, double-ended non-marking nail installation; No glass glue, no nailing, easy and fast installation, no nail holes, very satisfied!

Looking for a renovation company, you are too worried.

After playing with nails, touch-up paint is fine.

<> the construction method of the in-wall baseboard is measured first. The value of the baseboard is reserved in the wall, then grooved in the wall, and then the baseboard is placed in the groove. First of all, measure the length and width of the baseboard with a ruler, and then draw the corresponding position on the wall with the measured data, and then detect the wall to prevent the damage to the wires in the wall during construction, and then carry out the trench work, and finally use cement and stone slurry as the adhesive, embed the baseboard in the groove in the wall, and use the sewing agent to beautify the seam, place it to dry, and clean it up.

<> installation process includes wall leveling, cutting baseboards, installing buckles, installing baseboards, etc. First of all, the wall, the wall is smoothed, and the cement on the wall is even more smooth. The second is to cut the baseboard, which is cut according to the corresponding size.

The second is to install the buckle, determine the size of the buckle, use a nail gun to fix the buckle, and keep the buckle spacing up and down 40 cm. Finally, install the baseboard, cut the yin and yang corners, tear off the protective film, lift the baseboard up, press it again, and tap the baseboard to install it successfully.