Will the diatom mud fall off the slag and fade?

Yes. The construction environment requirements of diatom mud are very high, in addition to keeping the wall moist, there is also the construction of the over-fiber pants can not open the window for ventilation in order to meet the construction period, so that the diatom mud can dry naturally. If the air is relatively dry, then more water should be sprayed in the air and on the ground, which not only increases the humidity of the air, but also ensures that the diatom mud will not fall ash after construction.

Diatom mud still needs to maintain a certain humidity after construction, diatom mud has strong adsorption and water absorption, but if the dust particles attached to the wall are not regularly manually treated, it is not conducive to the diatom mud to play its function. For the diatom mud after the completion of the reed, we should still regularly clean the surface with a damp rag.

1. First of all, we must figure out why dust is generated. The principle of dust generation is that the dust in the air floats in the air, and the dust is floating, moving and rubbing against each other, and when the air humidity is less than 40%, the dust generates static electricity due to contact and friction, causing the dust to agglomerate and fall to form a return stroke.

2. The air humidity of the mountain stove is greater than 40%, and it will not produce static electricity and dust. This is the reason why the cities in southern China are clean and have very little indoor dust, while there is a lot of dust in the north. The root of this lies in the humidity of the air.

Because diatom mud is a high water storage material, in the case of dry air, the humidity in the room can be adjusted by pumping water on the wall, so as to eliminate static electricity and reduce the dust content in the air.

Before construction: before painting, diatom mud should be mixed with water, if the water is too much, the diatom mud will not only not cover the wall base, but also will appear powder and other phenomena. Qualified products will provide a clear ratio of water, which is theoretically the most scientific.

However, consumers do not need to be strict with the proportion of water, and the experience of the construction personnel themselves is worth learning from, and appropriate adjustments can be made for different environments. However, it is necessary to pay attention to the control amplitude, if you mix too much water, there will be powder loss, cracks and other phenomena.

During construction: confirm that the base of the wall has been treated, and the base is completely dry without hollowing. In addition, during construction, it should be noted that the main material of diatom mud should be flattened as much as possible during the first construction, and then textured to avoid the phenomenon of powder loss caused by the loosening of the wall caused by the large pores of the main material of diatom mud in the wall.

The reasons for the diatom mud powder are as follows:

1. Improper mixing with water.

If it is over-diluted, the adhesion of diatom mud itself will be affected, resulting in its inability to be as strong as some materials with more glue content, which will cause the diatom mud wall to fall powder.

2. Damage caused by light collection.

Some textures and processes (such as: diatom mud bomb coating) need to be treated when the diatom mud finish is semi-dry, if the timing or technique is not properly grasped, it is easy to leave burr stubble, and the specific surface area of these parts is larger, so it is easier to quickly lose water and dry, resulting in chalking.

3. Powder loss caused by too dry wall.

Nowadays, many construction walls are too dry, and construction technicians directly carry out construction in a hurry, resulting in powder loss after construction.

4. Powder loss caused by too thin spraying point.

During the construction process, if the diatom mud spray point is too thin, it may cause the diatom mud to fall off.

5. Powder loss caused by inferior products.

Diatom mud is an emerging environmentally friendly wallmaterial, and it has been reflected in the market as soon as it came out, and its efficacy has won the general support and recognition of consumers. However, some unknown brands produce inferior diatom mud, diatom mud indicators can not meet the specified requirements, resulting in serious wall powder in the later stage, so it is recommended to choose diatom mud to choose well-known brands, quality service is guaranteed.

First of all, the proportion of water, especially the excessive water in the close to liquid state of construction, diatom mud is made of inorganic materials, after being over-diluted can not be compared to some materials with more glue also has a good binding force, so the overall bonding pair will be reduced, thus causing the phenomenon of powder loss.

Secondly, it is an environmental factor, in a dry environment, it will also affect the phenomenon of diatom mud powder loss, and the water loss rate on the wall is too fast, resulting in rapid differentiation of the surface.

In addition, the diatom mud pressure is destroyed: because the area of some parts is much larger, it is easier to lose moisture and become dry, which leads to the phenomenon of pulverization.

In fact, you can use Yunquan diatom mud, they are constructed by the factory master, the workmanship is passed, the Tmall store has it, and the coconut net is also okay.

Construction reasons will lead to powder loss:

1. The problem of the proportion of water, especially the construction of excessive water in a near-liquid state, diatom mud is processed from inorganic materials, and after being over-diluted, it cannot have a good binding force like some materials with more glue, so the overall bonding pair will decrease, thus causing the phenomenon of powder loss.

2. Environmental factors, in a dry environment, will also lead to the phenomenon of diatom mud powder loss, and the water loss rate on the wall is too fast, resulting in rapid differentiation of the surface.

3. Diatom mud pressure is destroyed: because the area of some parts is much larger, it is easier to lose water and become dry, which leads to the phenomenon of pulverization.

There are many reasons, improper mixing of water, drying, my old house renovation is the use of Yunquan diatom mud, this product is completed after the house has no smell, and it does not fall off the powder, you can buy it in the Tmall store.

1. The problem of the proportion of water, especially the construction of excessive water in a near-liquid state, diatom mud is processed from inorganic materials, and after being over-diluted, it cannot have a good binding force like some materials with more glue, so the overall bonding pair will decrease, thus causing the phenomenon of powder loss.

2. Diatom mud collection problem, diatom mud has a lot of texture that needs to be collected, if in the process of collecting light, the master's technique is not right, there is no compaction, the wall will also appear to fall powder, and some do not need to collect the light of the texture, because the diatom mud is glue on the wall, so there may be some particles that are not adhered to the note, after the diatom mud wall is dried, use a feather duster to slightly dust the particles that are not attached to the wall, and there will be no more powder problem in the later stage.

3. Environmental factors, in a dry environment, will also lead to the phenomenon of diatom mud powder, such as some unexpert friends in the process of turning on floor heating air conditioning or using hair dryers and other artificial acceleration of wall drying, so that the wall water loss speed is too fast, which will also lead to wall powder.

Nowadays, the silicon bath will almost not cause dust, the silicon bath is really not 100% silicon bath, there is clay, glue, so there will be no smoke, but the darker the tone, will adhere to the dust, and at the same time the collection is not on, why does this happen, what causes this situation? Because there is a raw material 'resin rubber powder' in the silicon bath, the high-quality Shuzi Tan lipid rubber powder will not produce silicon bath customs, and the inferior quality is prone to silicon bath customs clearance.

Diatom mud paint is a dry powder, but when cold water is added to the wall, the powder will not float around. Because the wallcovering has the characteristics of moisture absorption, it will digest and absorb the moisture in the air, and it is not easy to dry out to the point of powder. It can be used with peace of mind.

Silicone bath can absorb formaldehyde, purify indoor air, suction wheel dehumidification, low-carbon environmental protection, is a kind of wall decoration board often used in recent years. In the construction process of silicon bath, in order to prevent the occurrence of powder loss, we must pay attention to the following aspects: the water retention of the wall during the construction process, the wall to prevent too dry, the construction process does not need to open the window for ventilation or prevent direct sunlight, the best silicon bath is of course dry; The proportion of water added should be carried out in accordance with the normative standards; The processing technology of paving and closing in the construction process must be done well.

Integrated wall decoration, if the construction situation, the above points are done, is not known to answer the problem of powder loss. Inferior silicon bath products will fall off the powder after the wall, but the quality of most of the silicon bath in the market is still guaranteed, and many of the main reasons for the powder loss are caused by external factors, so the owner does not need to panic in the case of choosing a silicon bath, and must be handed over to the technical professional wall master for construction during the project to ensure that the wooden door paint is made at a beautiful level.

The required value of silicon bath products is a functional material that is mainly oriented to physical and mental health, safety, and environmental protection. In-room applications can eliminate indoor formaldehyde, benzene, xylene, xylene, voc, radon and other harmful substances released by other brands. However, we should not shout under the guise of environmental protection and safety, but cause more damage to users.

Customers should also have the most basic level of identification, and they must not buy wallcovering products that have fallen off the powder.

Diatom mud is an environmentally friendly material that people like to use in the process of decoration now, and generally speaking, as long as the construction of high-quality diatom mud is selected, so that Bi Du will not appear to accompany this situation.

If the diatom mud decoration is used for a certain number of years, it is impossible for the powder to drift around, and the diatom mud decoration is actually very environmentally friendly, and it is also durable.

Not only will this powdery substance be messed up everywhere, but it will also lead to a decrease in air quality, which will also lead to air pollution.

Hello, I am Suzhou Natural Fang Wall Art, diatom mud powder is also normal, because the real diatom mud contains diatom powder, which contains a lot of loose small particles like carbon particles, which can absorb this and formaldehyde.

Diatom mud will lose powder, but most of the powder loss is caused by improper construction.

There are three main reasons for diatom powder loss caused by improper construction

First, the environment is too dry.

The environment includes the wall, the ground, and the air is dry, and the diatom mud itself has a strong ability to absorb and release moisture, and the water loss rate is too fast after being put on the wall, resulting in rapid pulverization of the surface. Before the construction of diatom mud, we must do a good job of water retention for the environment. The wall should be kept as moist as possible, and if possible, you can roll water on the wall first.

During the construction period, do not open the windows for ventilation or direct sunlight in order to catch up with the construction period, and let the diatom mud dry naturally.

2. Improper proportion of water.

The proportion of water should be blended according to the reference ratio provided by the manufacturer. If the excessive amount of water is applied in a near-liquid state, the diatom mud is mainly inorganic materials, and after being over-diluted, it cannot have good adhesion to some materials with more glue, which leads to the decline of the overall bonding strength and causes the surface to lose powder. Therefore, be sure to carefully read the product description and mix it with water according to the proportion on the description.

It should not be too thin. Third, the construction process is not professional.

Some textures need to be pressed when the surface of diatom mud is semi-dry, and if the timing or technique is not appropriate, it is easy to leave burr stubble, and the specific surface area of these parts is larger, which is more likely to lose water and dry quickly, resulting in chalking. This depends on the craftsmanship and technical proficiency and experience accumulation of the construction master.

The main ingredient of diatomaceous mud is diatomaceous earth, which has a powdery appearance. Diatom mud has 5000-6000 times more pores than activated carbon, so it has a strong adsorption capacity. The amount of diatomaceous earth content and the quality of diatomaceous earth have a great impact on the function of diatomaceous mud.

The formula of diatom mud is more complicated, and it takes a process to dry after the diatom mud is put on the wall. The surface feels dry to the touch and isn't really dry. At this time, if you touch or even rub it, the probability of dust sticking to your hands is also very high, and this detection method is very unscientific and undesirable.

Because rubbing in this state causes the diatom mud to lose powder, even after a few days of thorough drying, this area may permanently "lose powder" and become an indelible "scar".

A simple test method that consumers can master: after the diatom mud is dried on the wall for 7 days, touch the wall with the palm of your hand, do not press hard, and rotate the palm of your hand 45 degrees with your wrist as the axis, once you can. If more than 70% of the contact area between the palm and the wall has dust, this situation can be judged as the phenomenon of powder loss.

If there is only a small amount of dust, it is recommended to clean the surface and try again. If there is basically no dust, it can be judged that there is no powder loss.

If a mature wall material has the problem of large pieces of material dropping, it means that the material itself is not suitable for promotion or the material does not meet the industry standard, which is also a test method of diatom mud.

For a qualified marketed product, its basic quality must have been verified by the company's test and relevant testing institutions. I don't hear about what you mentioned in my work.

1.Improper mixing with water. 2. Damage caused by light collection.

3.The walls are too dry. It is best to use better quality diatom mud, so that this problem will not occur.

I suggest you use Yunquan diatom mud, which is beautiful and beautiful, and the walls are very textured, and they all have Tmall stores.

It could be due to improper mixing of water or the wall surface being too dry. I used Yunquan diatom mud for the decoration of my house, and the coconut net diatom mud is also good, I recommend going to their Tmall store to see.