LG drum washing machine shows the wrong time, and it can t be washed for half a day? 10

It is normal for the laundry program to be delayed for about 10 minutes due to water pressure, uneven clothes, etc., but the problem said by the landlord, the delay is too much, which is not a normal phenomenon. It could be the following problem points:

1. Bubble perception.

Is it laundry detergent.

Put too much? Can you see a lot of white foam from the side of the door? If it is, it is foam perception, too much foam, the washing machine perceives, it will automatically open a program to remove foam, this program takes a long time, which will lead to a significant extension of the program time, it may take nearly an hour at a time, if the foam is not fully washed off at one time, it will start again, in this case, you need to wait for it to end by itself, it is not a washing machine failure, you just need to pay attention to put less laundry detergent next time.

Drum washing machine.

It is very water-saving, so as long as the laundry detergent is small, the concentration is very high.

2. Water inlet failure.

You observe whether the machine can enter the water normally. However, if the water inlet fails, the water pressure is too low or the water inlet valve is blocked, and the specified water level cannot be entered within 4min, the program will report an IE error, if there is no error, it may not be a problem.

3. Drainage failure.

Does the machine have a lot of water that can't be drained? It is possible that there is a foreign object in the drain pump, and you need to clean the drain pump in the lower right corner, but if there is water in the bucket, turning on the drain pump will make the water flow to the ground, you need to turn off the program, open a single drain program to drain the water as much as possible, or when you turn on the drain pump, find some cloth or something to suck the water out there, or move the washing machine to the floor drain. Sometimes objects such as coins can get stuck in the drain pump.

Pay attention to the action of turning on the drain pump, do not operate with electricity, and unplug the power supply. If the drainage problem is severe, the program should also report an OE error.

4. The program is abnormal.

This situation does not occur very often, but it may not be normal because of some operations or voltage fluctuations, in this case you see how far the program is running, if it is being rinsed, you can turn off the machine and reopen it to rinse again to see if it is normal.

The problem you described is not very specific, so I will analyze these for the time being, and if it is not the above reason, please describe it in more detail to help you.

The drain pipe behind the drum washing machine is about 80cm higher! Did you put it down! This can happen if you put it down.

In the last 15 minutes, he showed what he was doing. At the same time, in what state is the machine.

LG drum washing machine failure** are PF, LE, TE, DHE, 1E, 0E, etc., the following explains the cause of the failure:

LG Washing Machine Display PF means LG Washing Machine Power Failure, Power Failure, Restart. Or the voltage is too high, the voltage is too low, and the voltage regulator part of the LG washing machine computer board is repaired.

LG washing machine display LE means that the washing barrel of LG washing machine does not rotate, check whether the inner barrel clutch is stuck, and check whether the washing machine motor is burned or the motor is heated.

The LG washing machine displays TE, which means that the LG washing machine does not heat up in the washing mode, and the washing heating is faulty (the heating tube is faulty or the thermistor is defective).

The DHE of the LG washing machine indicates that the LG washing machine does not dry, the drying heater is faulty, and the wiring of the drying heater of the LG washing machine is in poor contact and is used for drying.

LG washing machine display 1E means that the LG washing machine door is broken and there is a problem with the computer board, check whether the door lock is powered on.

LG washing machine display 1E means that the LG washing machine does not enter the water, check whether the faucet is open, whether the water pressure is too low, whether the faucet is frozen, whether the filter hand is blocked, and whether the water inlet valve is energized.

The LG washing machine shows 0E to indicate that the LG washing machine does not drain water, whether the drain pipe is bent or the support is too high, the drain motor is hot, and the drain motor is burned.

There are many reasons why the drum washing machine does not turn:

1. Check whether the washing is placed too much, and the load of the drum is too heavy, if so, only a part of the washing can be taken out to work normally.

2. Check whether the voltage is normal, because the voltage is too low, the output torque of the motor will not reach the specified value, and can not drive the drum to run, if so, it should be suspended or adjusted to the normal value with a booster.

3. Check whether the capacitor is normal, because the short circuit, open circuit, grounding and aging of the capacitor will make the motor unable to start and run normally, if the capacitor can not be used normally, it must be replaced with a new one of the same capacitor, and the motor will start and run normally.

4. Check whether the motor is normal, especially whether the starting winding of the motor will be broken, resulting in the failure to start normally, if it is abnormal, it is necessary to repair or replace the new motor.

Panasonic washing machine motor has a running sound and the drum does not rotate fault analysis.

Failure analysis of the washing machine motor running sound and the drum not turning When this kind of fault occurs, you should first check whether the washing is placed too much, and the load of the drum is too heavy, if so, you only need to take out a part of the washing to work normally.

Secondly, check whether the voltage is normal, because the voltage is too low will cause the output torque of the motor to reach.

If it is not the specified value, and cannot drive the drum to run, if so, it should be suspended or the voltage should be adjusted to the normal value with a booster.

After ruling out the above possibilities, it can be checked in the following order: first, with a screwdriver handle.

The fastening screw on the back cover plate of the washing machine is unscrewed, and the rear cover plate is removed, and the transmission part of the washing machine can be seen, and the V-belt is checked to see whether it is loose due to serious wear and tear caused by long-term use or other reasons, and it cannot play the role of transmitting torque.

Secondly 9 check whether the capacitor is normal, because the short circuit, open circuit, grounding and aging of the capacitor will make the motor can not start and run normally, if the capacitor has not been used normally, it must be replaced with a new one of the same capacitor, and the motor will start and run normally. Finally, check whether the motor is normal, especially whether the starting winding of the motor will not be broken, resulting in the failure to start normally, if it is abnormal, it is necessary to repair or replace the new motor.

Good luck.

If the motor is humming but not spinning when the washing machine is doing laundry, it may be a problem with the starting capacitor. If there is no sound from the motor, it may be that the lid linkage switch of the dehydration bucket is faulty.

Check that the belt is loose, check the pawls and clutch to see if the brakes are tight or if the mechanism plate on the drum cover is broken.

The automatic washing machine does not turn, hum does not turn, how to solve the problem that the motor is not rotating, some have a clutch, the motor is very hot, the starting capacitor may be broken, or the wire is off, causing the motor to not start, if there is no clutch, see if the motor is stuck, do not idle the belt first, the motor is stuck, whether it is stuck, if it is not stuck, most of the starting capacitors are problematic.

The dry tube does not rotate, generally in the following situations: the motor is burned (no reflection when energized), the starting capacitor is damaged (the motor cannot be started after power-on), the brake line is broken (the motor cannot be started after the power is on), the timer is damaged (after twisting and twisting, the timer has no ticking sound), the water seal is damaged (the water seal is damaged, the clothes are difficult to put on the official and do not turn, at this time the clothes tube can be heard to beat the sound), the line is open (generally visible with the eye).

Changing the Hall sensor solves the problem.

It may be that there is a problem with the starting capacitor.

Summary. Hello, 1.The bolt was loose, and then it couldn't get into the dehydration, and the display couldn't jump at this time, just 7 minutes.

2. It may be that the brakes of the LG drum washing machine are not released, and the motor load of the washing machine is overloaded. 3. There is a problem with the clutch of the LG drum washing machine. Suggested Treatment:

1. First of all, check whether it is not caused by the loosening of the adjusting rod nut on the drain valve, and the retractor cannot pull the drain valve core apart, so that the nut can be pulled apart. However, some models should check whether the tractor cable and the drain valve are loose, if the nut is not loose or the cable is not loose, the tractor may have been damaged, and the drain valve core cannot be opened, and the tractor should be replaced at this time. 2. The brake of the washing machine is not released, and the motor cannot be started due to overload, and the buzzing sound can be heard at this time, so you only need to adjust the drain pull rod.

3. Clutch problems need to be repaired or replaced. 4. If it has not been solved, it may be that the computer board has been damaged and needs to be repaired or replaced. Open the back cover of the washing machine, let the washing machine enter the dehydration program, and then observe whether the drain valve is pulled open by the retractor, if not, it may be that the computer board is malfunctioning or the retractor is malfunctioning; If you observe that the drain valve is pulled apart, but does not drain, it is a blockage in the drain pipe, and in most cases a blockage at the drain valve inlet.

Hello, 1.The bolt was loose, and then it couldn't get into the dehydration, and the display couldn't jump at this time, just 7 minutes. 2. It may be that the brakes of the LG drum washing machine are not released, and the motor load of the washing machine is overloaded.

3. There is a problem with the clutch of the LG drum washing machine. Suggested treatment: 1. First of all, check whether it is not caused by the loosening of the adjusting rod nut on the drain valve, and the retractor cannot pull the drain valve core apart, and then the nut should be strengthened so that the nut can open the drain valve core.

However, some models should check whether the tractor cable and the drain valve are loose, if the nut is not loose or the cable is not loose, the rough standby, the tractor may be damaged, can not open the drain valve core, at this time the tractor should be replaced. 2. The brake of the washing machine is not released, and the motor cannot be started due to overload, and the buzzing sound can be heard at this time, so you only need to adjust the drain pull rod. 3. Clutch problems need to be repaired or replaced.

4. If it has not been solved, it may be that the computer board has been damaged and needs to be repaired or replaced. Open the back cover of the stool core of the washing machine, let the washing machine enter the dehydration program, and then observe whether the drain valve is pulled open by the tractor, if not, it may be that the computer board is malfunctioning or the tractor is malfunctioning; If you observe that the drain valve is pulled apart, but does not drain, it is a blockage in the drain pipe, and in most cases a blockage at the drain valve inlet.

1. The adjustment rod nut on the drain valve of the LG drum washing machine is loose, and then it has not been able to enter the dehydration, and at this time, the display screen has not jumped in the past, just 7 minutes.

The approximate itinerary of the bucket washing procedure of the LG drum washing machine is as follows:

Start with water for 2 minutes, then heat and wash for about 50 minutes, then rinse twice with celery, and rinse for about 14 minutes.

It takes a total of 28 minutes, and the final dehydration is about 10 minutes, and the total travel time is about 1 hour and 30 minutes;

Your washing machine is normal, don't worry.

Does "program run to drain program" means stop when you enter the drain program or stop after draining? You check your program selection, some washing machines are set to something like "stop without draining--- keep the last water" will appear in the last step of drainage, dehydration will stop, leave the last time of water, if not for this reason, it is very likely that the water level sensor cannot be reset, and it may be necessary to replace the water level sensor.

Summary. The faults of LG drum washing machines mainly include the following: 1. FE:

Failure of inlet valves, sensors, etc. 2. PE: Pressure switches, computer boards, connectors, etc. are defective.

3. CE: Sensing too high current (bad IPM, short circuit motor, etc.). Fourth, le:

Defective speed sensors, motor connectors, etc. 5. LE: Overload, too much clothing.

6. TE: no heating fault. 7. AE:

Water leaks, unplug the power, and come to the door. 8. Dagger: heating failure.

9. DHE: drying failure. 10. PF:

The power supply of the washing machine is faulty.

Hello pro is happy to answer this question for you LG drum washing machine working timeout.

What is your specific problem? Can you elaborate on that? So that my side can better answer your questions.

The LG front-loading washing machine is working out for a timeout.

LG washing machine shows that DE can not work normallyLG automatic washing machine, such a fault is that the magnet on the door cover has fallen, this needs to find LG manufacturers Da Shi professional maintenance master to repair (due to the need to replace the special small magnet). When there is such a fault in the LG drum washing machine, if the computer board or water level sensor fails, you also need to find a professional master from the LG manufacturer to repair it, and you can't fix it yourself.

The faults of LG drum washing machines mainly include the following: a brigade forward return, FE: water inlet valve, sensor and other faults.

2. PE: Pressure switches, computer boards, connectors, etc. are defective. 3. CE:

Perceive too high current (bad IPM, motor dismantling and short circuit, etc.). 4. LE: Defective speed sensor, motor connector, etc.

5. LE: Overload, too much clothing. 6. TE:

No heating failure. 7. AE: Water leakage, unplug the power supply, and come to the door.

8. Dagger: heating failure. 9. DHE:

Drying failure. 10. PF: power failure of washing machine.