Haier front loading washing machine over water level protection shows E8 fault 30

E8 means that the voltage of the washing machine is low.

If the voltage is too low, the washing machine motor may not start, and if the voltage is too low for a long time, the temperature of the motor may rise and be damaged.

Causes & Solutions:

1. If the voltage fluctuation causes the washing machine to stop working, wait for the voltage to be normal before using the washing machine.

2. In this case, it is also possible that the load is faulty, the related circuit is soldered, the water level switch or safety switch is not in good contact, and the connector is loose. Inspect each of these aspects one by one and replace the damaged parts.

3. The washing machine shows that E8 is to protect the washing machine, when this happens, you can cut off the power and unplug the power plug from the socket, and then use the washing machine after the voltage is normal.

An E8 failure in a washing machine is the result of a damaged or poor contact with the water level sensor**. Cause of failure: The communication between the panel and the motherboard is faulty, the voltage is too low, it is recommended to check the power supply voltage and the motherboard; If the water level sensor is damaged or in poor contact, check whether the water level sensor and its circuit are connected well or see whether the air duct is flooded, and replace it if necessary.

Solution: The filter screen under the wave wheel of the laundry bucket is blocked, use a tool to pry open the sewage outlet under the washing machine, first use a basin to put the sewage under the prepared sewage outflow, and after opening, you can directly unscrew the lid and catch the sewage and discharge it. If E8 is still displayed after cleaning, it will be caused by the failure of the water level sensor or the circuit board to detect the power supply circuit, and the water level sensor is not in good contact with the socket on the computer board, so it is recommended to adjust and re-plug it.

Precautions for the use of drum washing machines.

It should be noted that drum washing machines are all strong drainage, and pump drainage, so it can be wall drainage or floor drainage. The width of the machine is 600 cm, the height is 850 cm, and the depth, the same number of kilograms, there are 300 cm to 500 cm, so you can pay attention to the choice when decorating.

If the drum washing machine is faulty, you should immediately contact the relevant manufacturer for maintenance, the main fault of the drum washing machine is to adjust the balance of the machine, the maintenance personnel will come to repair, do not try to repair by yourself.

The above content refers to Encyclopedia - Drum Washing Machine.

People's Daily Online-Dirt and dirt are hidden in the washing machine Do you know that the washing machine also needs to "take a bath"?

Haier washing machine shows that the E6 water level sensor is bad, it is recommended to find the manufacturer to check!

Haier washing machine failure**Daquan:

e0 did not close the door during the scheduled wash.

E1 drain timed out.

The E2 door is not closed properly or the door switch is broken.

The E3 washing machine is not flattened.

E4 water ingress timed out.

The E6 water level sensor is broken.

The E8 voltage is on the low side.

The E9 voltage is on the high side.

Hello. Haier drum washing machine over-water level protection shows E8 fault.

I repaired a Haier drum washing machine today, it turned out that the computer board was broken, and after replacing the board, the test machine appeared err8, and it was said that there was a problem with the water level sensor, and during the inspection process, it was found that the power supply plug of the drainage pump below fell off, and after the plug was plugged in, everything was normal in the test machine, and finally I didn't know what the reason was, because there was no wiring diagram for this washing machine, and only a line on the water level sensor was measured to be connected with a line of the drainage pump, I don't know why.

Unplug the No. 6 plug-in cable and power on the test machine, if the fault is still a problem with the computer board...

1. If the voltage fluctuation causes the washing machine to stop working, wait for the voltage to be normal before using the washing machine.

2. In this case, it is also possible that the load is faulty, the related circuit is soldered, the water level switch or safety switch is in poor contact, and the connector is connected.

Loose. Inspect each of these aspects one by one and replace the damaged parts.

3. The washing machine shows that E8 is a protective effect on the dust washing machine, when this kind of emotional combustion situation occurs, the power can be cut off, and the power plug can be unplugged from the socket, and the washing machine will be used after the voltage is normal.

How to deal with the E8 failure of the washing machine:

1. The filter screen under the wave wheel of the laundry bucket is blocked, use a tool to pry open the sewage outlet under the washing machine, first use a basin to put the prepared sewage flow out, and after opening, you can directly unscrew the lid and catch the sewage and discharge it. If E8 is still displayed after cleaning, it is due to a failure in the water level sensor or the circuit board to detect the power supply circuit.

2. The connection between the water level sensor and the socket on the computer board is not good, so it is recommended to adjust and re-plug it.

3. The plug of the water level sensor is not in good contact with the water level sensor, so it is recommended to adjust and re-plug it.

4. If the detection circuit of the computer board fails, it is recommended to repair or replace the computer board.

5. If the internal fault of the water level sensor is faulty, it is recommended to replace the water level sensor.

The above is the relevant content of the E8 failure of the washing machine, and the daily maintenance and cleaning work can greatly reduce the occurrence of equipment failure, and may also maintain a good experience of using the equipment for a long time.

This needs to see what is causing you, generally there will be no incident to call the police, you see if the lid is not closed when you wash the clothes, the door is not closed, this situation will cause the police, and there are more clothes than can be washed, there are many reasons will cause the police, you don't know if you don't elaborate.

E8 means that the voltage is too low, it is recommended that you check the power supply voltage and the motherboard.

Common faults of Haier wave wheel automatic washing machine** are:

e0: The upper cover was opened during the appointment process, and this ** needs to be opened and then covered E1: The drainage is timed out, check whether the drainage pipe is blocked.

E2: The lid is not properly covered.

E3: The dehydration is unbalanced, shake the clothes again and dehydrate againE4: The water inlet is overtimed, check the water pressure, and whether the water inlet valve is dirty and blocked.

E5: The water temperature is over 50 degrees.

E6: Whether you use high-foaming laundry detergent.

E7: If it is an environmental protection dual power display, E7 is due to the ambient temperature is too low E8: The voltage is too low.

e9: The voltage is too high.

It may be that there is a mistake in the operation, and there is a problem with that detail.

Haier washing machine special maintenance point in Qingyuan area.

Haier automatic washing machine failure**.

F1: The water level sensor of Haier washing machine is not in good contact.

E1: The drain of the Haier washing machine is overtimed, check whether the drain pipe is blockedE2: The upper cover of the Haier washing machine is not properly covered.

E3: The dehydration of the Haier washing machine is unbalanced, shake the clothes back and dehydrate them againE4: The water inlet of the Haier washing machine is timed out, check the water pressure, and whether the water inlet valve is dirty and blockedE5: The water temperature of the Haier washing machine exceeds 50 degrees.

E6: Does Haier washing machine use high-foam laundry detergentHaier drum laundry E8 *Haier drum washing machine over-water level protection (inlet and drainage failure) HTD, BS68, D08A, BS58, D09, D08, S06A, 60-HT, BS08E9 *Haier drum washing machine over-water level protection (but washing water level is not detected) D08A, BS58, D08

Haier washing machine has an E8 fault**, which means that the voltage of the washing machine is low. If the voltage is too low, the washing machine motor may not start, and if the voltage is too low for a long time, the temperature of the motor may rise and be damaged. When this happens, you can turn off the power and unplug the power plug from the socket, and then use the washing machine after the voltage is normal.

Questions. The voltage is normal.

In this case, it is also possible that the load is faulty, the relevant electric slip circuit is welded, the water level is turned on and off, or the safety switch is in poor contact, and the connector is loose. Inspect each of these aspects one by one and replace the damaged parts.