Can the pasted wall tiles be cut again?

Can be cut, with an electric angle grinder! It can be cut and edging at will, and the size is well controlled. Hope it helps.

Can a tiled wall be cut? There is no way to cut the wall tiles that have been laid, if you want to cut them, you can only knock out the tiles and install the cut tiles. If it is cut on it, it is difficult, and the entire wall may crack with it.

When knocking on the tile, the force must be skillful, if the force is too large, the tile will collapse directly, which is a very dangerous thing. When laying tiles, you must think about it before pasting, otherwise it will be very troublesome to modify it later. Additional Information:

Precautions: 1. Before paving the wall tiles, we need to treat them with the base layer. Dust and stains are removed from the surface of the base layer first, and then the putty and paint layers on its surface are removed.

At the same time, the flatness of the base should be checked, if the base is uneven, it is also necessary to level with cement mortar, otherwise it will affect the paving effect of the wall tiles. 2. Lofting and pre-paving: After the base is cleaned, the wall tiles can not be laid directly, but a few elevation control lines should be popped up with ink lines around the wall, and cross lines should be popped up on the ground to control the size of each floor tile.

Then the tiles are pre-laid according to the requirements of the decoration, and the effect of the decoration is checked and adjusted. 3. Modulate the wall tile binder: add appropriate water to the binder slurry, mix and stir evenly, and then let it stand for five to ten minutes, and then stir for 1-2 minutes to start using it.

Summary. Enlarge the tile gap for the pasted tiles, is it okay to use a cutter: Yes, you can choose a cutter and.

It is possible to use a special tile grinding disc, it is best to buy the kind with a 45-degree angle, and then it is okay to have a tile shelf. There is a slide on the shelf, adjust the height and push it back and forth. You can increase the gap of the tile, and it is a 45-degree angle, but the surface gap is increased, and the in-depth analysis has not changed.

But if you want to do this in every crevice after laying the tiles. Then there must be such equipment, otherwise it will not be able to grind.

Is it okay to enlarge the tile gap for the tiles that have been pasted and use a cutting machine?

Enlarge the gap between the tiles and use the cutting machine: Yes, you can choose the cutting machine and. The use of special porcelain bumper car brick grinding disc is OK, it is best to buy the kind of 45-degree angle, and then it is OK to have a tile shelf.

There is a slide on the shelf, adjust the height and push it back and forth. You can increase the gap of the tile, and it is a 45-degree angle, but the surface gap is increased, and the in-depth analysis has not changed. But if you want to do it in every crevice after paving the tiles and changing the tiles.

Then there must be such equipment, otherwise it will not be able to grind.

Because the wall tiles in my house are seamless, there are hollow cracks, can you use a cutting machine to increase the gap between the tiles?

No, first the joints between the arched tiles and other tiles are sawed with a cutting machine, and the tiles should be hail and lifted very carefully, and the action must be light, otherwise it is easy to cause the tiles to crack. 2. Scrape off all the cement mortar that sticks to the edge of the tile. Treat the cement layer under the bricks, plane off 1-2 cm and clean it up.

3. Evenly coated with a layer of mixed cement mortar. Fourth, the cleaned tiles are re-paved, flattened, and then reinforced with a caulking machine after the cement is completely dry, so as to avoid the phenomenon of upturned and cracking of the floor tiles. It can also be used to fill the void with grouting; First, use a paper cutter to clean the grout.

After removing the grout, it is obvious that you can find the hollow drum, and the paper cutter can go very deep. And good cement slurry, to be thinner. Place the cement slurry in the brick joints.

Use a small shovel to make gaps to facilitate the entry of the grout. The cement slurry is very thin, mainly through the water carrying the mud into the tile underneath, the water penetrates into the sand base, and the cement stops on the surface of the sand base, thus repairing the hollow drum.

Can you recommend me a master in this area, there is this equipment.

The master you find to post you has this.

I've been laying bricks for 10 years.

.If you inquire a little bit about the nearby tilers, they all know someone who will do this.

I'm looking for companies here.

Can't you expand the joints directly on the wall, I want to expand all of them, and then make up the current beauty sewing agent.

There's no need to make it a lot like a renovation.

If it's broken, fix it.

That can be made up. This platform does not allow -

You can find someone who is more experienced and get it for you, it's very simple.

How to cut half of the pasted floor tiles so as not to collapse the porcelain Dear, hello no wax! 1. If you want to cut and assemble without collapsing, you can choose some slices with high precision and good quality. There are thousands of manufacturers producing slices in the market, but there is a big gap in quality, and there may be a quality gap in the same way, so it is best to find a person who knows more to help us buy better quality cutting pieces, so that even if our technical deviation is a little, it will not lead to the collapse of the edge of the tile.

2. When cutting, we can push at a uniform speed, don't push too fast, don't push too slowly, don't stay in one place for a long time, try to keep your strength even, so that it will not cause the tile to collapse. 3. If we don't know which tile slice is good or bad, then we use a special cutting piece, which is very important. There are cutting discs that specialize in cutting ceramic tiles, and other cutting discs are used to cut tiles that are actually very easy to chip.

4. If Gaoguo is just an amateur operator, it is actually very difficult to make the tile not collapse. Therefore, when cutting tiles, you must pay attention to the technique and the correct operation method. Failure to do so will also cause the tile to chipping during the cutting process.