How do I cook headphones? How to cook headphones

The burn-in machine is to some extent equivalent to the car running-in, and the special burn-in is to get it into the state as soon as possible. But headphones also have a lifespan, so turning on the machine is equivalent to letting the air listen to songs for you for hundreds of hours.

In general, listen to a song that is not too intense at just the right volume for the first week, and then you don't need to pay attention to it.

If you really want to cook, just connect to the radio and tune to a blank frequency band. Or the next piece of pink noise on the Internet has been playing. If you use ** pot, it is best to take care of the high, medium and low frequencies. Note: Not an hour or so, stop for 10 minutes.

Hope you are satisfied.

Generally applicableCook headphonesHow:"Step by step"At first, use a softer **, let the headphones soothe for 10-30 hours at a lower volume, and then boil for 100-200 hours at medium volume with a normal ** (except rock and dance music). The treble is mellow and not harsh, the midrange is warm and friendly, and the low end is full of detail.

No matter what it is.

The volume of the music audio should not be too large, as too much volume will directly burn the headphones and damage the diaphragm. Professional burn-in audio is not suitable for listening with headphones all the time, especially in the low and ultra-high bands of swept signals.

Note. 1. Rock electronic music is disabled, and this kind of ** bass is suddenly pushed sharply, which is very damaging to the new headphones. It is recommended to cook headphones lightly**, white noise.

2. Slow cooking, cooking headphones must not be in a hurry, using too much volume often not only can not improve the sound quality, but cause irreversible damage.

3. For the first 24 hours, gradually use 1 3 to normal volume below the normal use volume, and gradually activate the diaphragm. 12 hours of normal volume, **often listened to**, 12 hours of normal use.

The purpose of the special burn-in is to get the headphones into the state as soon as possible. Here's how:

1.In general, listen to less intense tunes at just the right volume for the first week.

2.If you really want to cook, just connect to the radio and tune to a blank frequency band. The pink noise of the sedan chair or the next section of the net has been played. If you use ** pot for hunger, it is best to take care of the high, medium and low frequencies.

Headphones:

1.It is a type of headphone that is worn on the head, not inserted into the ear canal, and is different from in-ear earbuds. It consists of two parts, a signal transmitter and a headset (usually dynamic type) with a signal reception and amplification device.

2.The transmitter is connected to the signal source, and a preamp or headphone amplifier can also be plugged in front of the transmitter to improve sound quality and adjust timbre.

Headphone burn-in is a rapid aging process of the mechanical system of the headphones, the sound system of the dynamic headphones is driven by the voice coil, and the diaphragm is fixed to the shelf of the headphones. Theoretically speaking, the diaphragm movement should be a piston (vertical) movement, which requires the edge of the diaphragm to have greater compliance, the pot is the pot here, the edge of the diaphragm of the new earphone is relatively tight, the elasticity is large and the compliance is small, the earphone is to let it rise late The edge is active, and the sound is not so tight.

The "pot" of the earphone is actually in the pot diaphragm fold ring, the new headphone diaphragm fold ring mechanical compliance is poor, resulting in a relatively large distortion, after a period of use, the compliance gradually improves, and the distortion will gradually drop to a normal level.

For the headphone amplifier, as long as it is not turned off, it is burned, but for headphones, a certain power signal must also be fed to make the diaphragm vibrate constantly. Professional enthusiasts use a special frequency generator to generate a fixed or scanned frequency and then input it to the headphones, which is more effective and can shorten the time used.

In the process of boiling, we should pay attention to two points: one is that it cannot work continuously for too long, because there is resistance in the voice coil, it will heat up after working for a long time, and even burn the voice coil. It's best to stop for a few minutes every two hours before continuing.

Second, the volume should not be too large, the earbud diaphragm is a very fragile material next to the code, if the volume is large, the stroke of the voice coil movement will be large, so as to pull the diaphragm violently, which will cause the voice coil to loosen, the diaphragm to deform or even tear and so on. Causing the sound of the headphones to be abnormal.