How to change the car wipers, how to replace the car wipers

If the interface of the wiper blade is in-line, press the small button on the wiper arm with one hand so that the wiper can move, and pull the wiper outward with the other hand to remove the wiper. Insert the new wiper directly into the wiper arm for installation.

The wiper blade is divided into positive and co-pilot side, A refers to the driver's side, B refers to the co-pilot side, its curvature is different, and the size is also different.

The wiper blades of different interfaces are replaced differently, and the following is a brief introduction to the replacement steps of the U-shaped interface.

1. When disassembling and assembling the wipers, put a cloth on the windshield and completely stand up the wipers. Prop up the wiper and change the wiper angle.

2. Change the angle of the wiper blade, preferably at a 90-degree angle with the wiper swing arm.

3. After placing it according to the angle, you can start disassembling and assembling. The rubber wiper blade is lifted with one hand to expose the hook between the wiper swing arm and the wiper blade. The wiper blade is removed as a whole, and the rubber wiper blade is broken horizontally with one hand below, and the other hand is pressed down the main bracket to separate the wiper blade from the swing arm, after which the wiper blade can be taken off as a whole.

Generally, the service life of the wiper is one year. It doesn't matter if it's from a 4S store or bought from outside.

Determine that the wiper is time to change: Clean the glass surface before confirming. Touch the surface of the glass with your hands to make sure that the glass is free of scratches and raised particles. Wipe the wiper strip with a cotton cloth, strictly prohibit vigorous efforts, and confirm whether the strip is scratched, deformed or jagged.

Under normal circumstances, if there is still a waterline or the sound is particularly loud, or it is not clear, you can consider replacing the wipers.

Explanation: Wipers, also known as wipers, water picks, wipers or windshield wipers, are equipment used to brush and scrape away rain and dust attached to the windshield of vehicles to improve the visibility of drivers and increase driving safety. Because of the legal requirements, cars in almost all places carry windshield wipers.

Vehicles such as hatchbacks and minivans are also equipped with wipers in the rear windows. In addition to automobiles, windshield wipers are also installed in other means of transportation, such as trains and trams. Some part of the engineering equipment, I hope thank you.

1. First, lift the metal wiper arm from the windshield and keep it stable perpendicular to the windshield.

2. Then press the stopper, and remove the old wiper blade, separate it from the metal arm, insert the new wiper, and gently turn the new wiper blade.

3. Finally put the wiper back on the windshield until the hook clicks into place to secure it.

How to change the car wiper blade, this is not simple, the main thing is that the wiper blade currently has two cards, see how to remove the wiper blade, and pay attention to the wiper arm do not touch the glass.

Here's how to replace your car's wipers:1. First of all, we put a rag on the windshield in front of the wiper to avoid scratching the glass.

2. Then we stand up the wipers, preferably at a 90-degree angle to the wiper swing arm.

3. After we put it according to the angle, we can start to disassemble and assemble, first lift the rubber wiper blade with one hand, then remove the wiper blade as a whole, and break the rubber wiper horizontally with one hand below.

4. Then we use the other hand to press down on the main bracket to separate the wiper blade from the swing arm, so that the wiper can be taken down as a whole.

5. Finally, we can reinstall the new wipers.

The steps to replace your car wiper are as follows:

1. Stand up the wipers.

2. Press and hold the clip.

3. Remove the wipers from the original car, but don't let the rocker arm bounce back and break the front windshield.

4. the front end of the clip in the middle for installation.

5. Tighten the clip inserted in the middle, and get into place when you hear a click.

6. The wiper size of the driver's seat and the co-pilot's seat of some models is different, generally the driver's seat is longer, and the co-driver's seat is shorter, which should be paid attention to when installing.

7. To install the wiper in the passenger seat, you need to look at the direction, and at the same time you need to tighten it, and when you hear a click, the installation will be completed.

Summary: First align the wiper card slot and the plastic part in the swing arm; Then aim at the wiper card slot with both hands and press it hard, when you hear a "click" sound; Finally, move the rear wiper from side to side to make sure the wiper is secured.

When you go to the car beauty and decoration store, you can replace it, or you can buy your own wiper blades with an operating process on the package, and follow the map.

Find a repairman and change the wiper blades yourself.

Shakespeare once said: No matter how beautiful things are, they will be lost one day. And the wiper blades we are talking about are no exception, it may just be a matter of the length of use, when the aging of the wiper is very serious, it needs to be replaced in time.

So how often do you change the wiper blades, if you want to know the answer, read on.

Generally speaking, the replacement cycle of wiper blades is 1-2 years, but it still depends on the quality of the wiper blades. Because poor quality wiper blades often do not have good heat resistance. Then under the long-term scorching sun, it will not only reduce the service life of the wiper blade, which may need to be replaced in less than half a year, but also has a great impact on the wiper effect.

So if you buy a bad quality wiper blade, it's best to replace it with a new one.

Replacement steps for wiper blades:

1.First, raise the side wiper arm in the driver's position at 90 degrees, and then raise the passenger-side wiper arm.

2.Then lift its U-shaped buckle and pull down the wiper and take out the wiper blades. But be careful with the rocker bouncing back so you don't hurt your fingers.

3.Then you can directly install the new wiper blades, press and hold the middle sides of the wiper, and lift the card cover up.

4.Finally, pass the cover of the wiper blade through the middle of the wiper arm, press the buckle and you're done.

Wiper use and maintenance guide:

1. Use the wiper to remove the dust on the surface of the windshield on a sunny day; Be sure to spray the glass with water; Do not dry scrape.

2. There are other stubborn and hard dirt on the glass; It should be cleaned by hand. These things can easily injure wiper blades; As a result, the wipers are not clean. Seriously; The motor of the wiper will also be affected.

3. When the wiper blades need to be lifted for car washing and daily cleaning; Hold the "back" of the wiper blades; Gently send it back when you put it; Don't snap the wiper blade back.

4. When used in winter; Ice ballast on the windshield surface should be cleaned with an ice shovel first; so as not to increase the burden of the wipers.

1. In order to avoid damage to the windshield during disassembly, it is recommended that the owner put a cloth on the windshield when disassembling and installing the wiper, and support the wiper to change the angle of the wiper;

2. Then change the angle of the wiper blade, it is best to make it at a 90-degree angle with the wiper swing arm, because the wiper blade and the swing arm are stuck with clips, so it is easy to disassemble and assemble after a certain angle;

3. After putting it at an angle, you can start disassembling and assembling, first lift the rubber wiper blade with one hand, in order to expose the fixed hook of the wiper swing arm and the wiper blade, remove the wiper blade as a whole, break the rubber wiper blade horizontally with one hand below, and press the main bracket down with the other hand to separate the wiper blade from the swing arm, and then the wiper blade can be taken down as a whole;

4. The installation is not difficult, first pull up the cover in the middle of the wiper blade, pass the wiper support through the middle, buckle into the bayonet of the wiper, tighten the final cover and add the cover.

Teach you how to change a car wiper? The method is simple and easy to learn, and you don't have to spend money to go to a 4S store anymore.

Wipers are rubber and plastic products, and it is best to change them once a year. If the wipers' ability to sweep water is reduced, it will be difficult to observe the ground conditions when driving in the rain. Especially when the car is moving, the wiper blades start from the **, and the water sweeping ability is worse.

In addition, driving in the drizzle, the small raindrops that are not cleaned will have a variety of refractions in the light, making the vision in front extremely blurred, which is very easy to cause safety accidents. The following is the process of replacing the wiper:

1. This is a fixed wiper blade, a hook.

2. Then get the direction of the wiper blade right, and put the slot on the hook inside.

3. Then press in.

4. Pull in with your hand in reverse.

5. Then close the outer cover of the decorative design.

Wipers, also known as wipers, water dials, wipers or windshield wipers, are machines and equipment used to scrape off raindrops and dust adhered to the front windshield of automobiles to improve the driver's visibility and promote safe driving. Due to laws and regulations, almost all cars in locations contain windshield wipers. Cars such as sedans and minivans are also equipped with windshield wipers on the rear windows.

In addition to cars, other modes of transportation are also equipped with wipers, such as trains, electric cars, etc.

There are five steps to replace the wiper in the car, first of all, the owner needs to remove the original wiper, and replace the new wiper according to the removal method. The steps are as follows.

1. Step 1: Dismantle the original wiper first and stand up the wiper as shown in the figure below.

2. Step 2: Press and hold the clip below to remove the old wipers. This is shown in the figure below.

3. Step 3: Remove the wiper of the original car from one side. This is shown in the figure below.

4. Step 4: the front end of the middle clip a little and load the new wiper in. This is shown in the figure below.

5. Step 5: Insert the new wiper into the middle clip and tighten it, and hear a click of the wiper in place. This is shown in the figure below.

6. Finally, the wiper installation is completed. This is shown in the figure below.

Notes:Some models have different wiper sizes for the driver's seat and the passenger seat, generally the length of the driver's seat, and the short passenger seat should not be installed incorrectly.

1.Follow the direction of the wipers and naturally lift the wiper arm upwards to move it away from the body.

2.Tilt the wiper blades back so that they are perpendicular to the wiper arm.

3.Locate the fixed buckle where the wiper blade and wiper arm are attached.

4.Pull the tabs outwards and stretch the wiper blades outward.

5.Then pull the buckle to the side to undo it from the wiper blade attachment.

Take the new Qijun car as an example. 1.Open the groove of the boneless wiper, gently pull down until the wiper is separated from the wiper arm, and then lift it up to disassemble it. Open the groove of the new wiper, align it with the U-shaped groove of the wiper arm and install it, lift it up, and cover the lid.

The car wiper is very easy to change the punch card buckle and install it in place.