How to change a car spare tire? How to change the spare tire of a car?

1. Park the car with a flat tire on the right, take out the warning sign from the car, and place it about 100-150 meters away from the back of the car.

2. Then take out the tire change kit from the car, with spare tires, jacks, wrenches, etc., and prepare to change tires.

3. Use a jack to lift the side of the puncture tire first, and remember to top it on the steel beam or the girder under the chassis.

4. Then use a special wrench for tire disassembly and assembly to unscrew all the screws on the hub.

5. After unscrewing the screws, pull the tire out vigorously and take out the entire broken tire.

8. Find a place to repair tires as soon as possible, check the specific situation of broken tires, and either repair or change tires, because there are not many roads to drive for spare tires.

8. Find a place to repair tires as soon as possible, check the specific situation of broken tires, and either repair or change tires, because there are not many roads to drive for spare tires.

8. Find a place to repair tires as soon as possible, check the specific situation of broken tires, and either repair or change tires, because there are not many roads to drive for spare tires.

First of all, car owners should disassemble the damaged tires and loosen the screws with a wrench, but at this time they must not remove them, and the screws can be loosened. Then use the jack to jack up, the support position of the jack should be found correctly, and do not need to top too high to disassemble the tire on the line, and finally install the tire, align and fix the spare tire with the screw hole, and ensure that the screw is tightened.

If you are changing the spare tire on the road, you must first protect your own safety, you must first find a safe area to park the car, and then erect a warning sign, placed 50-100 meters behind the car, 150 meters on the highway, if you change the tire at night, you must also do a good job of light warning, which is also for the sake of safety. In normal times, because the spare tire may not be used for a long time, everyone should do a good job in the maintenance and inspection of the spare tire, and then the spare tire can not be used for a long time after the replacement is replaced, even if it is a full-size spare tire. Because the long-term use of spare tires with large differences in parameters will have a certain impact on the braking system, steering system and suspension part of the car, which may cause safety problems.

Before changing the spare tire, park the vehicle in a safe place that does not affect the pedestrian traffic of other vehicles. Try not to park at the entrance of the office, unit, community, or school. Traffic flow at a large intersection. Slopes.

If you stop on an expressway or a section of the road where the speed limit is high, change the spare tire. Then set up a warning triangle 100m behind the car (remember to take it back after changing the tire).Turn on the vehicle's double flash.

A manual transmission puts the gear lever in neutral position, and an automatic transmission puts the gear lever in the "P" (parking) position and pulls up the hand brake lever to turn off the engine. To prevent the car from moving when it is jacked up, try to place obstacles in front of and behind the tires diagonally to be replaced.

1. Open the tail box and take out the spare tire and disassemble the tire tool;

2. Use a wrench to loosen the screws on the tire; (Left loose and right tight).

3. Use a jack to jack up one side of the tire to be replaced; (There is a special place for jacks under the car.) Touch it with your hand. thicker than elsewhere).

4. Then use a wrench to unscrew all the screws of the entire tire and remove the tire;

5. Align the spare tire with the screw or screw eye, and twist a screw first, then twist all at once, and finally tighten it slightly with a wrench; (Symmetrical twist screw).

6. Loosen the jack and remove it;

7. Tighten the screws diagonally with a wrench, twist 1 4 of the whole circle each time, and repeat 2 to 3 times.

8. Put away the tools, put them back in the tail box, and put the tires back.

9. Done!

I don't know what kind of spare tire you are talking about, if it is an ordinary car spare tire, you can first loosen the broken tire screws, and then use a jack to jack up the tire you want to change, take out the tire from the trunk, replace the bad tire, and finally tighten the spare tire, and that's it.

Loosen the tire screws first, then take the frame machine to lift the vehicle, remove the screws and tires, and then fix the spare tire alignment bolts and start to put on the screws, tighten and lower the vehicle to let the tires touch the ground and complete the replacement of the spare tire after tightening the screws.

Quick and easy way to change the spare tire Can't remember** at the end.

To change the spare tire of the car, first make sure that the spare tire has enough gas, and then use the tools inside to replace the broken wheel, lift the car with a jack, and then replace the spare tire.

Take out the hand jack, spare tire and sleeve, put the jack on the lower beam of the vehicle, shake the jack, use the sleeve to loosen the tire screws after slightly resisting (the strength is limited, you can use the pedal sleeve rod to operate), after completing the above operations, shake the jack again until the tire is off the ground, completely unscrew the screws and remove the broken tire and replace it with the spare tire, and finally fix the tire with one hand to the maximum extent and tighten the screw with the sleeve with the other hand, put down the jack, and tighten the screw again by pedaling the sleeve rod.

Quick and easy way to change the spare tire Can't remember** at the end.

Quick and easy way to change the spare tire Can't remember** at the end.

1. Use a wrench to loosen the screws on the wheel, but don't unscrew it to avoid the tires running out, and don't hit the jack first.

2. Use a jack to put it on the edge of the bottom rib in front of the bad tire, and there is a thickened position. After that, beat the jack up and let the tires off the ground, but not too much, just a little.

3. After that, change to the spare tire, tighten the screws by hand, do not use a wrench.

4. After the screw cannot be screwed by hand, put it down and take out the jack. Then tighten the screws with a wrench.

5. Pack up the tools, put the bad tires, drive to the tire repair place, it is best to repair the tire as soon as possible, because the spare tire is generally placed for a long time, the air pressure is generally low, and the short distance is OK, and the continuous long road is not good.

Tools needed: spare tire, jack, wrench,

1. Put a heavy object (such as a stone, concrete brick, spare tire, etc.) in front of the front and rear tires.

2. Take out the spare tire and jack, place the jack under the frame close to the tire you want to replace, and make sure the jack touches the metal part of the frame.

3. Raise the jack until it supports (not lift) the car, the jack should be firmly under the vehicle, check and make sure that the jack is at right angles to the ground.

4. Remove the hub cover and loosen the nut in a counterclockwise direction. Never loosen the nut completely, as long as it's enough to remove the drag, and when you first loosen the nut, keeping the tire on the ground will ensure that you're turning the nut and not the tire.

5. Twitch or turn the jack to lift the tire off the ground, and you need to lift it to a height high enough to remove the flat tire and replace it with a spare tire.

6. Loosen all the nuts completely, turn the nuts in a counterclockwise direction until they are loose, repeat this step for all the claw nuts, and remove the nuts completely.

7. Remove the tires and put the flat tires under the vehicle, then if the 11,000 pounds fail, the vehicle will also fall on the old tires, and the car can be avoided by this method.

8. Put the spare tire on the hub, carefully align the spare tire rim with the wheel bolts, and then install the wheel claw nuts.

9. Tighten the nuts by hand until all nuts are tightened.

10. Lower the car and remove the jack so that the spare tire can be replaced.

Drive off the main road, pull over, turn on the vehicle warning lights, pull up the handbrake, and do the following.

1.Open the trunk, find the red cuboid box, open the box and take out the warning triangle, and place it fifty meters behind the car.

2.Take out the hand jack, spare tire and sleeve, put the jack on the lower beam of the vehicle, shake the jack, use the sleeve to loosen the tire screws after slightly resisting (the strength is limited, you can use the pedal sleeve rod to operate), after completing the above operations, shake the jack again until the tire is off the ground, completely unscrew the screws and remove the broken tire and replace it with the spare tire, and finally fix the tire with one hand to the maximum extent and tighten the screw with the sleeve with the other hand, put down the jack, and tighten the screw again by pedaling the sleeve rod.

2.Take out the spare tire and tools, and use a wrench to loosen all the screws in a diagonal direction in a counterclockwise direction. Find a load-bearing beam on the site and jack it up until the tire is off the ground;

3.Remove all the screws and remove the tire, put it at the bottom of the car to prevent the jack from slipping, align the screws and install the spare tire, and install the diagonal square.