What should I do if the floor tiles are higher than the floor at the joints between the floor and th

This problem is very common in old houses, if the corridor is now 4 cm higher, then the thick floor should be about a centimeter after the paving. It is also higher than centimeters, and you can use the bevel pressure strip you said is a universal buckle. But choose a slightly wider one, so that the bevel looks smaller, you can choose a 5 cm or 6 cm one.

If you are not satisfied, you can also choose two right angles, which should be metal, one large and one small on the stain, so that a centimeter of steps is out, but it is relatively strong and not easy to fall. How to do it depends on your preference.

The general way is to install the beads:

1. Flat strip: used to cover two floors and floors of the same horizontal height, and the gap between the floor and floor tiles.

Note: The gap treatment and closing problems when the floor is paved to the end are left to 7 notes to deal with.

It is most often found in the following places: no baseboards, floors, steps, stair openings.

3. High and low buckles:

1) If there is a difference between the height of the floor tile and the wooden floor, use the height buckle.

2) You can also calculate the elevation of the finished surface of the two before laying the wooden floor and the floor tiles, the two are flat, and install an additional keel under the flat interface, and then the place where the floor and the floor tiles meet, the floor is poured at an angle of 1-2mm and then smoothed with transparent silicone.

4. If it is a solid wood floor, the kind that needs to be fixed with nails, and the place where the floor tile is connected can not be pressed without a strip, generally this situation will be in the same plane, the flat strip is basically located under the door, and the strip is invisible after closing the door, and the solid wood floor has been fixed on the keel, and it will not be greatly affected by cold and hot deformation, and there are many families who do not install strips in this situation.

This problem is easy to solve. When laying the floor, lay a thick layer of geothermal treasure (extruded plastic board) on the ground. That's it.

This kind of problem is generally not understood by those who sell flooring, you can ask the local flooring installer. It is a technical issue.

1. Flat strips.

It is a material that covers the same ground with two horizontal heights, which can not only deal with the gap between the floor and the floor tiles, but also the gap between the floor and the floor, which brings a very good effect and is also a commonly used material.

2. Seven notes.

When the floor is laid on the edge, it can be used to deal with the gaps or close the mouth, which can play a protective role. The position of the commonly used seven-character strip is generally in places where baseboards cannot be used, and it must be said that the platform, steps, etc.

3. High and low buckles:

It can be used for the height difference between the floor and the floor tiles, which is generally used before the floor tiles and wooden floors, and the height difference between the two is calculated, and then the construction is carried out.

4. Do not use beads.

Nowadays, most families will choose not to use beads when laying wooden floors, and use staples to fix, which can also achieve good results. Since some solid wood floors are already fixed to the keel, they will not be affected by thermal expansion and contraction, so there is no need to install beads.

A few details before the construction of the floor.

1. Before laying the wooden floor, the construction surface needs to be treated flat and clean, so as to lay the wooden floor correctly and prevent the situation of drumming and falling off, which will affect the normal use.

2. After the wooden floor is transported to the site, it should not be constructed immediately, but placed for a period of time, so that it can be integrated with the ambient temperature in the construction site before construction, which can reduce unnecessary trouble.

I summarize: what are the four major methods of dealing with the joints of floors and floor tiles, as well as a few details before the construction of the floor, I will introduce them here, do you understand it? The joints between the floor and the floor tiles need to be treated well in order to bring good results and facilitate normal use in the later stage.

1. Flat strip, flat strip is used to cover two floors of the same horizontal height, which can be used to make up for the gap between the floor and the floor, and can also be used to make up for the gap between the floor and the floor tiles.

Notes, 7 notes are to solve the floor to the end of the treatment, the treatment of gaps and the treatment of closing, 7 notes are most commonly used in these few places without baseboards, floors, steps or stairs openings.

3. High and low buckles, high and low buckles are used when there is a gap between the floor tiles and the floor. This can be done before laying wooden floors and floor tiles, it is necessary to calculate the elevation after the completion of the project, and the specific operation bricklayer and the master of the flooring company will communicate.

4. Do not use the strip, now there are many families also choose to lay solid wood flooring, if it is fixed with staples, then the place connected with the floor can not be pressed strip, and there are some pure solid wood floor slag itself has been fixed on the keel, the impact of thermal expansion and contraction is very small, at this time there is no need to install macro quiet strip.

1. The tile is uneven, which itself belongs to the product defect or deficiency of the ceramic tile manufacturer, but it is not necessarily a product quality problem, because only its deviation exceeds the national standard or the enterprise's own requirements, it can be identified as a quality problem. As far as the national standard for the flatness requirements of ceramic tiles is concerned, the standard is relatively relaxed. It is not more than the standard plane, such as 800 * 800 specifications of the tile converted to millimeters error value is, and the maximum error value does not exceed 2mm.

From this point of view, it is difficult to estimate the difficulty of holding the tile party accountable.

2. The responsibility of the construction party has two points: there is no inspection of the tiles before the tile is paved, which is required to be done in the ceramic tile construction specifications, and the construction party does not operate according to this operation belongs to the problems in the construction.

3. The paving specification of ceramic tiles requires that the height difference between the joints between bricks is less than that, and if the height difference between the joints exceeds mm, the construction party should also temporarily stop the construction party and notify the owner of the tiles.

The unevenness of the floor tiles is caused by the unevenness of the surface, at this time, you have to evenly wipe the surface with mortar, which will be very smooth from the outside, and then you will not have the unevenness of the floor tiles on top.

Nowadays, many families will not only use one kind of ground decoration material when decorating, but will use a combination of floors, that is, the living room, kitchen, and bathroom choose to lay floor tiles, which are not only wear-resistant and easy to take care of, but also moisture-proof and anti-slip; For bedrooms and study rooms, you can choose to have comfortable parquet flooring or parquet. This combination makes better use of the advantages of floor tiles and flooring. However, due to the different construction techniques when laying floor tiles and floors, and the construction personnel are also different, if the owner does not have on-site supervision, the paved ground is prone to height differences.

Usually, laminate flooring requires adding a keel underneath. However, some construction workers tried to save trouble and persuaded the owners not to add keels and lay the floor directly on the leveled ground. Because the cement cushion is needed when laying the floor tiles, and the thickness of the cement is generally not less than the times of the thickness of the floor tiles, in this way, the thickness of the original floor tiles themselves and the composite floor is similar, and the result is that one adds the cement cushion and one does not add the keel, resulting in the height difference when the two materials are connected.

In addition to affecting the appearance, there are also potential safety hazards, and it is easy for the elderly or children at home to plant their heads when they walk. Therefore, whether it is laying floor tiles or floors on the curved front, it is an important process in the decoration, and the two must be combined with stools for construction, and the owner needs to carefully supervise the work. When you need to lay floor tiles and floors in the living room, before laying, you must ask the construction personnel in detail about the laying technology and the effect after laying, as well as whether there is a height difference between the two, and then determine the laying plan.

The owner must supervise the construction personnel to carry out the construction according to the requirements of the two different processes. When laying the floor, it is better to lay a backing plate or keel under the floor to reduce the height difference. At the junction of the floor tiles and the floor, you can use the Dali Journey Stone interface or use a metal buckle.

When transitioning with marble, the side in contact with the floor should be ground into a slope so that the transition is more natural. The material of the buckle is copper and aluminum alloy, the color is gold, silver, matte, polished, etc., and there are a variety of styles and widths. When constructing, it must be carried out in strict accordance with the specifications to avoid the buckle from being warped or falling off in the future.

Chen Yanmei).

The best way to do this is to use 7 notes!

It doesn't feel like it could get any better than that!