What to do if the floor tiles are dyed and colored, and what to do if the floor tiles are discolored

Causes of discoloration of floor tiles:

OneThe water absorption rate is too high.

This is also the most common condition. The water absorption rate of ceramic tiles is too high, indicating that it contains high ceramic content and is easy to penetrate into liquid. After the tile is laid, the tile sucks the water from the wet cement mortar from the back, and the water enters the glaze to produce imprints, resulting in discoloration.

Solution: When buying tiles, you can judge the water absorption rate of tiles by using the water droplet test method: drop the water droplets on the back of the tile, and after a few minutes, the more water droplets remain, the lower the water absorption of the tile. If you find that the water stain spreads to the inside of the tile, it means that the water absorption rate of the tile is too high, and the chance of discoloration after paving is also higher.

IIThe glaze is too thin.

The glaze of the tile is like a protective film, which can effectively prevent fouling, waterproofing, corrosion, etc., if the glaze layer is too thin, the anti-fouling ability of the tile will also deteriorate, and a large amount of dirt will enter and accumulate in the tile, which will cause the brick color to change. Glaze that is too thin can also lead to problems such as deglazing, glaze loss, and glaze cracking.

Solution: When buying tiles, observe the thickness between the embryo body and the glaze from the side. Secondly, the glaze gloss of high-quality glazed tiles is very high, and it is warm and delicate to the touch.

IIIIf the tile is not soaked in water, the brick that has not been soaked in water or is not soaked enough is pasted on the wall, and the tile will also absorb the moisture in the cement after being put on the wall, resulting in a color change. The time and number of soaking in water are also related, and the new bricks soaked in water once after paving and the old bricks soaked in water twice will have color difference problems. Using the wrong cleaner can remove different stains from the surface of the tile, but it can also have an adverse effect on the surface and internal composition of the tile.

Solution: When the owner buys, it is best to consult the pH resistance and other properties of the tile, so as to choose the right detergent to prevent the glaze from being contaminated.

Selection skills: 1. The appearance color should be uniform, the surface gloss and flatness should be good (except for special processes), especially the polished floor tiles should pay more attention to their gloss, the higher the gloss, the more exquisite the polishing process, the higher the relative hardness, so as to have low water absorption and higher wear resistance.

2. Good anti-pollution ability. Drop one or two drops of ink or colored water on the surface of the tile, wipe it off with a damp rag after half an hour, if there are obvious marks, it is easy to seep; If there is basically no trace, it proves that it has good anti-fouling ability.

3. The size deviation should not be too large. That is, the four bricks are put together, which should be relatively regular and have no obvious dislocation. If the size error is greater than the flatness, it will not only increase the difficulty of construction, but also the effect after decoration is also poor, so it cannot be used in the project.

4. The water absorption rate should meet the requirements. The lower the water absorption, the higher the density of the product, the less permeable it is. Usually the colored ceramic tiles are not more than 10%; Unglazed porcelain tiles (including polished tiles) shall not exceed; Glazed porcelain tiles are not more than 1%.

The discoloration of the floor tiles is really difficult to solve, which can only mean that the quality of the floor tiles you choose is too poor. If you really can't see it, I suggest that you can solve it by laying laminate flooring on top of the floor tiles, which is relatively the least costly.

How to deal with the color of the floor dye, there are many house decoration materials on the market now, the floor decoration of a good house is good-looking, for the cleaning of the floor should also pay attention to the method, the tips in life can help you clean quickly, the following shares how to deal with the color of the floor dye.

The first thing is to clean it with a floor cleaner, because some of the floors are more stubbornly stained, so it will be more effective to use a floor cleaner.

Then use soapy water and a rag to clean the floor tiles.

Because soapy water still has a good cleaning effect, and at the same time, every house has soap, so it can be used.

The second is that you can use a brush dipped in detergent to try to brush, so you can see the effect slowly, so it is also very convenient to use a brush.

Then there is the use of hydrogen peroxide.

to clean the tiles, but use a cotton swab to wipe them cleanly.

Then it is to use toothpaste to remove tile staining, toothpaste has a good effect on whitening teeth, and naturally has the same stain removal effect on tiles.

The floor tiles are dyed with color, and the treatment steps are as follows:

1. Pour 1 capful of laundry detergent into the mineral water bottle.

2. Pour in 2 capfuls of white vinegar.

3. Pour in 3 capfuls of alcohol.

4. Finally, pour in half a cap of flour and mix well.

5. You can start to clean it, dip some mixture and wipe it with a scouring pad in the place that needs to be cleaned, and the tile will be as clean as new.

Workaround:

Preparation for cleaning: edible alkali, white vinegar, water, absorbent mop, basin.

Step 1: Pour the water into the basin.

Step 2: Then sprinkle edible alkali into the basin of water (edible alkali has a good cleaning effect and can clean off the dirt on the floor tiles).

Step 3: Then pour 10ml of white vinegar into the basin of water (white vinegar can soften the dirt on the floor tiles).

Step 4: Pour the homemade solution from the basin onto the floor tiles.

Step 5: Use an absorbent mop to vigorously mop the floor tiles.

Step 6: The dirt on the floor tiles has been mopped off.

There are generally three cases of discoloration of floor tiles:

1. The completion time is short, the floor tiles are not dry, and the color difference occurs due to the difference in water content.

2. The process reason for the paving of floor tiles is that the floor tiles are paved without sufficient water absorption, resulting in the thickness of the wall on the floor tiles and still absorbing the moisture in the cement, resulting in the phenomenon of penetrating the bottom;

3. The quality of the floor tiles is relatively thin and uneven, as long as there is some moisture on the surface, it will cause discoloration.

AbstractYou can try this method:

Step 1: Pour an appropriate amount of laundry detergent into the watering can (laundry detergent has a good cleaning and stain removal effect).

Step 2: Then pour the liquor into the watering can (liquor is water-soluble, which makes the solidified pigment water-soluble).

Step 3: Then pour an appropriate amount of white vinegar into the watering can (white vinegar contains acetic acid, which can break down the solidified pigment).

Step 4: Then pour an appropriate amount of flour into the watering can (flour can absorb water-soluble pigments).

Step 5: Screw the lid on the watering can and shake the laundry detergent, flour, liquor, and white vinegar by hand evenly.

Step 6: Use a watering can to spray the tiles and carefully wipe the colored parts of the tiles with a scouring pad.

Step 7: The color on the floor tiles has been cleaned.

What to do if the floor tiles are stained.

Hello This is a very good question, I need a little time to answer, please be patient.

I bought Jane a marble tile, because it was wet by the rain during transportation, and the back was stained, is it a return or quasi-processing.

Here's how you can try: Step 1: Pour an appropriate amount of laundry detergent into the watering can (laundry detergent has a great cleaning and stain removal effect).

Step 2: Then pour the liquor into the watering can (liquor is water-soluble, which makes the solidified pigment water-soluble). Step 3:

Then pour an appropriate amount of white vinegar into the watering can (white vinegar contains acetic acid, which can break down the solidified pigment). Step 4: Then pour an appropriate amount of flour into the watering can (flour can absorb water-soluble pigments).

Step 5: Screw the lid on the watering can and shake the laundry detergent, flour, liquor, and white vinegar by hand evenly. Step 6:

Use a watering can to spray the tiles and carefully wipe the colored parts of the tiles with a scouring pad. Step 7: The color on the floor tiles has been cleaned.

You can give this method a try.

You can also make a return.

In this case, will it have an impact after paving?

It's just that it doesn't look good, and it depends on what color it is dyed.

In the pro who is in.

Dyed blue.

What color is the floor?

It is gray and the back is white.

It just doesn't look pretty.

Do you know what blue pigment is?

Hello, you can consider these two methods ha:

1.It can be removed with dish soap, laundry detergent, etc., some brands are equipped with special cleaning agents, the cleaning effect is better, and special cleaning agents such as super water, Mr. Wittmann, etc. are sold in floor tile sales merchants or large supermarkets.

Hello, you can consider these two methods ha:1It can be removed with dish soap, laundry detergent, etc., some brands are equipped with special cleaning agents, the cleaning effect is better, and special cleaning agents such as super water, Mr. Wittmann, etc. are sold in floor tile sales merchants or large supermarkets.

2.Lemon juice has citric acid, you can also squeeze the juice of fresh lemon on the dyed floor tiles and rub it repeatedly, if there is no fresh lemon, you can also use vitamin C tablets instead. Citric acid is one of the most commonly used cleaning products.