The photocopier is damp and the copying effect is not good, what is the way to deal with it?

Generally, when the photocopier is damp, there will be four phenomena: partial whiteness of the copy, blank copying at startup, wrinkled paper and lines in the copy. Can be solved in a simple way:

The first is the partial graying of the photocopy, which is the photosensitive drum of the photocopier.

If the surface is caused by moisture, the solution is to turn on the machine and warm it up for 30 minutes, and then use the copier.

The second situation is the phenomenon of blank copying on startup, which is the leakage of the copier in operation after being damp, and the same can be turned on to preheat and try again, if it cannot be solved, it is necessary to ask a professional to come to repair.

The third situation is that the copied paper is wrinkled, which is caused by the moisture of the paper, you can replace the paper, do not open the package and put it in the air when using the paper, to ensure that the paper is not damp.

The fourth situation is that lines appear on the surface of the copy, which is caused by the moisture of the copy development shaft, which can be turned off and then turned on to preheat and keep it dry.

To avoid these situations, the first thing is to prepare the photocopier for moisture in advance.

For daily moisture-proof work, it is best to put the photocopier in a dry place, not near the window, nor directly on the ground, especially away from the water dispenser and water source, in order to prevent the impact of indoor moisture on the machine. In addition, to improve the performance, it is best to preheat it before use to dry up the dryer and damp; If you don't use it often, it's best to cover it with something, preferably about half a meter from the ground.

In order to ensure the quality of the photocopier, it is also necessary to properly keep the paper used for copying, put some hygroscopic bags in the cabinet where the paper is stored, and seal the paper in a dry cabinet when the weather is bad to ensure that the paper is not damp.

It is worth noting that do not unplug the power of the photocopier at will, and ensure that the power is on after shutting down, so as to ensure that the machine is dry when it is not in use at night. In wet weather, even if there is no need for copying, turn on the machine and keep it dry.

Not only toner, but also the body can be dried when it is damp, and there is no problem after drying.

There is generally no problem when the machine is turned on in humid weather, the key is that the paper is easy to get wet, and you can buy a thermostat.

Try to use dried paper, turn on the machine early in the morning, and use a hair dryer to blow down the rotary seat of the machine if you are really in a hurry.

Use a hair dryer to blow the transfer and charge.

First of all, the first thing to do before going to work every day is to turn on the photocopier to warm up, which can be used to dry the moisture and small water droplets inside the equipment;

The company can try to avoid the opening of doors and windows, a large amount of ventilation will cause the indoor humidity to rise, resulting in paper jams, paper moisture, unclear printing output and other situations. Secondly, you can turn off the copier switch after work every day, but do not unplug the power plug to ensure that the inside of the copier can be kept dry at night.

In addition, when placing office equipment, it should be kept away from relatively humid locations such as mineral pots, water sources, drinking stools, and water jets, so as to prevent moisture failures caused by the indoor environment. After the desiccant, you can put a box of desiccant.

It is placed in the photocopier tray rented by the color copier in the East Side to keep the paper dry and reduce paper jams. Do not expose paper to the air, and implement a system of using as much as you want.

A photocopier is one of the essential pieces of equipment in a modern office space. However, if the copier is wet, it will affect its normal use, and even short circuit or damage. So, what to do if the copier gets wet?

As a first step, immediately cut off the power supply and unplug it. If there is a fire extinguishing switch between the electrical outlet and the wire, it should be turned on.

In the second step, the moisture inside the photocopier is removed. All removed parts can be cleaned, including flat glass, A4 trays, toner cartridges, driver cartridges, and more.

The third step is to dry all parts of the copier. Circuit boards and electrical components, in particular, must be thoroughly dried to ensure that there is no short circuit. It is best to use a soft cloth or cotton yarn with good water absorption and trembling smile.

Step 4: Place the photocopier in a ventilated and dry place. You can use a hair dryer or air conditioner to speed up drying. However, be careful not to blow the hair dryer or air conditioner outlet directly inside the copier, so as not to cause other problems.

Step 5: Wait for at least 24 hours to turn on the power again. Always make sure that the individual parts are completely dry before restarting. Otherwise, moisture may cause damage to the circuit board and electrical components.

In short, when the photocopier is damp, it is necessary to stop using the source immediately and take a series of necessary measures to deal with it. If you can't handle it yourself, it's best to ask a professional technician to overhaul it. This ensures the proper use of the copier and avoids bigger problems.

When the photocopier gets wet, the impact on the machine is very large. The humid environment can easily lead to problems such as short circuits on the circuit board, damage to the printer motor, and clogged ink cartridges. If it cannot be dealt with in time, it will affect the normal use of the machine. Here are a few ways to repair a photocopier after it gets wet.

Method 1: Dry with an electric fan.

When you find that the photocopier is wet, you first need to turn off the power of the machine. Then, use an electric fan to blow dry the machine, especially the printer motor and circuit board. During the blow-drying process, it is necessary to carry socks to avoid blowing into the ink cartridge and other vulnerable parts.

In addition, if the photocopier has been damp for a long time, it is recommended to disassemble the machine and dry the internal parts separately.

Method 2: Place desiccant to absorb moisture.

After the machine is blow dry, some desiccant needs to be placed inside the copier. For example, you can put a packet of desiccant in the cartridge compartment or in the light box of a projection device. The desiccant has a good effect of absorbing moisture, and the machine can be completely dried in one day.

Method 3: Replace the parts.

Sometimes, moisture on the copier, which may cause damage to certain parts of the machine, such as circuit boards, printer motors, etc. At this point, these parts need to be replaced. In general, the accessories of the popular models of photocopiers can be purchased on the market.

It should be noted that when replacing parts, you need to ensure that you are skilled in operation, otherwise it is recommended to seek the assistance of professional after-sales first to avoid damage to the machine hidden grip or greater loss.

Method 4: Repair.

If the photocopier still does not work properly after being wet, it is recommended to take the machine to a professional repair facility for repair. The repair shop will conduct a thorough inspection of the copier, determine the root cause of the problem, and repair or replace the relevant parts. Before making a repair, it is advisable to ask the repair shop's professional for repair options and estimated costs.

To sum up, when the photocopier is wet, it needs to be cleaned and repaired in time. Be careful to turn off the power of the machine before handling to avoid electrical shock. For copiers with minor conditions, using an electric fan to blow dry and place desiccant will do the trick.

For more serious copies, replacement parts or professional repair are required.

The photocopier is damp and does not lack seepage to use, put it in a ventilated and cool place, leave it for a period of time, and then turn on the power for a period of time to try to make the volcanic ridge use, if there is a specific problem, in the specific solution.

The photocopier is one of the commonly used equipment in our daily life and office, but in the process of using the copier, if there is a failure or can not be used normally, what should be done at this time? Here are some common ways to deal with copiers.

1.Cannot turn on or boot properly.

If your copier doesn't turn on or start properly, you can check whether the power cord is plugged in tightly and the power is turned on. If the power supply has been turned on and it still can't be turned on normally, you can check whether there is a power failure. At this time, you can unplug the power cord for 10 seconds and then plug it back in again, and then try to see if it can turn on normally.

2.Paper jam or paper jam occurs.

When the copier's paper card or paper jam is stuck, the power should be cut off before processing. Then open the front cover of the machine, remove the jammed paper, and then check if there are any other paper jams, and if so, clean up by the way. Once all the paper has been processed, restart the machine.

3.The printing results are not ideal.

If you find that the photocopier does not print well, you can first check whether the consumables are normal, such as whether the toner cartridge is dry, whether the consumables have been used up, whether the consumables are not suitable, etc. Then the printhead can be cleaned, checked for blockage, etc.

4.Faults ** digging rules.

If the photocopier is faulty, you first need to check the fault explanation of the studio in the manual, and then troubleshoot according to the fault. For example, it could be caused by a hardware failure, a software problem, a malwiring or a faulty line.

Through the above processing methods, you can easily solve some common copier faults, so that you can use the copier stably for a long time and improve work efficiency. At the same time, it is necessary to pay attention to the usual maintenance and regular replacement of consumables to reduce the probability of failure and prolong the life of the copier.

1. External environment: The temperature of the photocopier is insisted on at 15 degrees Celsius.

Insist on humidity at 25 to 75%, place the machine in a dry place when placing the photocopier, and keep away from drinking oak water machines, mineral pots, and water sources. In this way, malfunctions due to moisture in the room can be avoided.

2. Ventilation: In the humid room, ventilation should be insisted on to reduce the humidity in the room, and prevent problems such as paper jams and unclear prints. Preheat and dry: Every morning after work, turn on the copy reed machine to preheat the moisture in the dryer.

3. Paper moisture-proof: insist on paper dryness, and place a box of drying agent in the photocopier carton to adhere to the dryness of paper. After using up the copy paper every day, wrap the copy paper and put it in a boring cabinet. Try to avoid leftovers every time you use copy paper.

4. Power supply: After getting off work every day, after turning off the switch of the copier, do not unplug the power plug, so that the photocopier will be boring at night. Rainy weather:

In rainy weather, pay attention to the moisture protection of the copier. During the day, it should be turned on and insisted on boring, and at night to avoid moisture entering the machine.

Said one by one. 1. a photocopier; First of all, the paper is susceptible to moisture, so it must be loose when using the paper in wet weather. The second is the copier itself, because it uses toner transfer printing and high-temperature fixing, so it should be turned on for about 30 minutes in advance in wet weather.

Of course, it is best to install a constant temperature dehumidifying air conditioner.

2. In addition to laser printers, other printers only need to pay attention to the loose paper. Laser printers and photocopiers should be kept in mind.

3. a computer; As long as there is not a lot of dust in the computer host, the general wet weather will not affect the host. For monitors, the CRT type is more affected, and sometimes the display is blurry, but after 20 minutes, it is generally normal; LCD displays are generally unaffected.

You're talking about jams, right?!

Recently, I also have such problems with these machines, which are mainly caused by moisture on the paper, and have nothing to do with the printer.

Secondly, when the printer adds powder, you must choose the best toner, otherwise it will cause the toner to agglomerate, and there will be ink, powder leakage and other phenomena when printed!

As for desktop computers, due to the unstable humidity in the room, it is easy to cause poor contact of memory modules, so it is OK to plug and unplug them again.

Yes, copiers, printers.

To make a good promise of paper (that is, to spread the paper into a piece, so that it comes out one by one, not several together - I don't know how to describe it), close the door in wet weather, do not put too much paper in the photocopier carton at a time, and put the paper at a high point from the ground to prevent moisture absorption.

The photocopier is prone to malfunction in a humid environment, and even damage the machine, affecting the use effect. Therefore, solving the wet problem of the photocopier and ensuring the normal operation of the machine is a skill that every user must master.

When the copier is found to be wet, it should be stopped immediately and the machine should be moved to a dry environment for inspection and repair. If there are water droplets or moisture on the surface of the machine, you can use a tool such as a dry cloth or hair dryer to remove it to avoid further corrosion and damage to the machine.

Before servicing a wet copier, it is necessary to disconnect the power supply to avoid safety issues such as electric shock. At the same time, it is necessary to disassemble the machine shell for thorough cleaning, including cleaning the impression drum, developer, fuser and other parts to prevent moisture from entering the machine from these parts and causing machine failure.

In addition, the paper used in the photocopier should also be replaced in time to avoid deformation of the paper caused by excessive humidity, which will affect the quality of copying and the life of the machine. If you need to store spare paper, you should choose a dry environment and seal it with a sealed bag or box to avoid moisture and dust ingress.

Keeping the machine in a clean and dry environment can effectively reduce the risk of the machine being exposed to moisture. At the same time, regular maintenance and maintenance, such as replacing damaged parts, cleaning impurities, etc., can prolong the service life of the machine and ensure work efficiency and output quality.

Overall, proper handling of the dampness of the photocopier can avoid damage to the machine and ensure the normal operation of the machine. Therefore, when using the copier, it is necessary to pay attention to maintaining cleanliness and maintenance to avoid moisture conditions and improve the service life and performance of the machine.