How do you tie a balloon? How to tie a balloon

Quickly untie the knotted balloon:

1.Find a metal rod that is not sharp, such as the tail of an ear picker;

2.Thread a metal rod into the knot of the balloon and it's easy to solve.

3.If the balloon is too full, you can wait a few days and then solve it this way.

Balloon knotting method:

Pinch 1cm below the mouthpiece with your left index finger, thumb and middle finger at the same time, and then use your right hand to pull this 1cm reserved uninflated part, preferably to more than 8cm.

Hold the end of the mouthpiece with your right hand and wrap it from the outside to the inside, with the middle and index fingers wrapping around it.

At this point, open your middle finger. The middle finger needs some strength at this point.

Wrap your right hand around the gap formed between your index and middle fingers and grasp the mouthpiece.

Pull out your middle finger and you'll notice that the knot is already tied.

The following is how to tie the balloon.

1: We need to prepare the most basic things, balloons.

2: Inflatable equipment.

3: Inflate the balloon and inflate it to the right size.

4: Put down the inflatable stick, at this time hold the ball mouth with one hand and the other hand to hold the ball in the position shown in the picture and pull the ball mouthpiece, about 5-7 cm long.

<> 6: After going around a circle, pull the ball mouth over and place it in the middle position.

7: At this point, the ball mouth is released from the right hand, and the index finger and thumb of the left hand are caught in the ball mouth.

8: Retract the two fingers that hold the ball mouth, and then the ball mouth will naturally come over to complete the knot tying operation.

Teach you the trick of tying a balloon knot quickly.

Here's how to tie a balloon:

1. Blow up the balloon first, but don't blow it too big, and reserve a length of 5mm to 1cm to make it easy to tie the knot.

2. Pinch the tail end of the balloon with your left hand, touch the end of the balloon with your index finger in a circle, and fix it with your thumb.

3. Fix the tail end of the balloon towards the tip of the index finger with your right hand, pull the tail of the balloon tightly around the circle, pull it out of the circle and tie it into a knot, and tie the knot tightly.

A balloon is a sealed bag filled with air or some other gas. Balloons can be used not only as toys, but also as a means of transport. There are many types of balloons, now the main introduction of natural latex production of balloons, can be used as a limb decoration, the opening ceremony of the arch, can be printed on their own advertising pattern to eliminate as publicity, can be printed on the wedding couple's photo as a congratulations, can be decorated ball, newlyweds floats, etc., now balloons have become a beautiful landscape, more and more favored by people!

Balloons used to be called "eggplant" as a toy, and there was a small bamboo whistle at the opening of the balloon, and when the balloon was blown full of air, the exit would be very loud. Balloons can also be used as decorations and as a means of transport. If the balloon is large enough and the gas inside is lighter than the same volume of air, the buoyancy generated exceeds the weight of the airbag and attached objects (e.g. gondolas, hot air balloons, etc.), the balloon can be raised.

How to use the balloon knotter:

1. First of all, press the pump with your hand to inflate the balloon, put the knotting device on the three fingers of our left hand or right hand, and pull the inflated balloon mouth with one hand, and pull it from one side of the knotting device to the other side.

2. Then pull the balloon mouth around the knotting device and put the balloon mouth into the card slot in a knotted way.

3. After the final knotting is completed, the clan pulls out the balloon mouth, so that the balloon is easily knotted.

Precautions for the use of balloon knotsters:

1. When winding, I didn't use my thumb to resist the balloon, only the index finger and middle finger were entangled, and it turned out that the air valve couldn't be plugged in. Pinch the tail end of the balloon with your left hand, reserve about 5mm, circle the balloon along the index finger, touch the tail end of the balloon and fix it with your thumb.

2. The force generated by the deformation of the more rotations cannot automatically wrap those circles back. So as long as you don't step on it and screw him and other strenuous activities, there will be no air leakage.