Will the glue under the toilet leak 1?

Toilets. The lower glue will leak, and now there is no need for glass glue.

It's expensive and smelly to beat glass glue, and it's not easy for ordinary people to get it.

Novices need to prepare additions: gloves (to prevent cutting hands), rain boots (to prevent heavy wet shoes), waste rags (gloves are afraid of dirty), utility knife or fruit knife (not strong enough).

Three-step operation:

1. Tear off the wrapping paper of the yellow butter flange for the toilet bowl that you bought and put it aside, put on gloves, change into rain boots, close the water inlet valve behind the toilet, and press and hold the flush for three seconds to drain the water in the water tank.

2. Use a utility knife or fruit knife to cut off the glue under the toilet bowl (unless the old bird, you must wear gloves for this action, it is very troublesome to cut your hands), push the toilet up (it is more labor-saving to leave half of the glue), and wipe the bottom of the toilet with a waste rag.

3. Stick the yellow butter flange ring for the toilet bowl you bought, aim it at the toilet outlet, and then slowly put the toilet back into place. Sit on the toilet and take out your mobile phone to like, swipe WeChat, and press it for a while.

Key Matters: 1) Safe operation is the first priority, pay attention to your hands when cutting glass glue. The first time I repaired the toilet, my hands were cut.

2) After using the toilet special yellow butter flange ring, there is no need to use glass glue, this material is airtight and pressure-sensitive damping is very good, after sitting on it and pressing it, unless you push it up from the side with great force, otherwise the toilet will not move.

This general situation is not to leak air, because there is a sealing ring below, as long as the sealing ring is not aging, he will not leak, I hope it will help you.

The glue under the toilet will not leak, because there is a rubber ring under the toilet, as long as the rubber ring does not leak, there is nothing to open the glue, it is estimated that it is the one that fixes the toilet, so don't worry.

Check whether the sealing ring of the toilet drain is damaged, put a new sealing ring on the toilet drain, align the drain with the sewer pipe, make the toilet straight, and then reapply glass glue.

1. a sealing ring.

If the toilet leaks due to failure, you need to remove the toilet, replace it with a new sealing ring, and install and fix the toilet according to the design requirements.

2. If the toilet leakage caused by the misalignment of the sewage caliber, you need to remove the toilet, align the ground with the sewage caliber of the toilet, adjust the position of the toilet, seal the pipe interface, and install the toilet as required. The bottom of the toilet bowl is smeared with glass glue.

After that, wait two to three days before using it.

It is not okay to not glue under the toilet. If the toilet can not be firmly fixed, once there is displacement, the soft connection of the drainage pipe will be destroyed first, and the interface will leak, and it will smell bad from the interface, and the problem will be serious.

No, it must be beaten, and glue must be applied around it to fix the position of the toilet bowl and ensure that there is no water or air leakage. Usually the location is determined, then the toilet is squatted on the ground, aligned with the drain, and then glued along the edge. Finally, wipe off the spilled glue and let it stand for 2-3 days to remove the excess gel.

If you don't glue under the toilet, it will easily leak. Therefore, sometimes the water is flushed downward, and the water under the toilet bowl is not able to come out, and it is easy to expose from the edge of the toilet.

The toilet base is not glued, and the non-glue is not for fear of leakage, but when mopping the floor, the dirty water enters the toilet base, and the more it accumulates, the more you can imagine the taste.

The bottom of the toilet must be glued, which is waterproof that the sewer pipe leaks and then leaks out of the ground. It also prevents the outside water from entering the inside of the toilet when mopping the floor outside, so it must be glued!

No, if you don't use waterproof glue, it will leak.

The reasons for a leak at the bottom of the toilet are as follows:1. There are problems in the installation process of the toilet, resulting in the misalignment of the sewage outlet on the ground with the toilet sewage diameter, so that there will be yellow water, water and odor.

2. The installation is not professional, and the flange is not installed (the flange has a good fixing and anti-spill effect).

3. Long-term use is suitable for the loosening of the toilet and the ground.

4. The toilet toilet itself is a problem with cracks in the ceramics.

5. Many toilet installations are omitted to be fixed with expansion bolts, and directly fixed and sealed with strong adhesive silicone, sealed with putty for a long time, which will harden and cause cracking and leakage, and if the silica gel is not fully cleaned before bonding, it is also easy to produce local water leakage.

The cause of leakage at the bottom of the toilet bowl is also the root cause of the leakage of the toilet, which is the failure of the sealing ring. Because the sewer pipe of the toilet bowl and the drain pipe we reserve are sealed by rubber rings, if the rubber rings are not sealed properly, it will lead to water seepage and leakage in these parts. Slowly, the water will leak outward.

The cause of the leakage in the lower part of the toilet is the failure of the sealing of the bottom of the toilet and the floor tiles. That is to say, at the root of the toilet we have beaten the glass glue has appeared to open the glue, if there is water seepage in the lower part of my toilet at this time, the water will seep to the ground through these parts of the glue, at this time we will find that the lower part of the toilet has leakage.

Find out the real cause of the leak at the bottom of the toilet bowl and see if it is a leak at the bottom of the toilet bowl or the toilet flush, or if there is a blockage under the toilet.

If the rim of the toilet is leaking, just scrape the glue off the rim. If a hard object clogs the toilet, you need to disassemble the toilet bowl and then glue it to fix it. Or due to the long use of time, the toilet bottom accessories are loose and leaking, then glue and replace the accessories.

1. Find out the real cause of the leakage at the bottom of the toilet, and see if it is a leak at the bottom of the toilet or the toilet flush, or a blockage under the toilet.

2. If the edge of the toilet is leaking, then scrape the edge of the glue clean.

3. If the toilet is blocked by a hard object, it needs to be disassembled and then glued and fixed.

4. Or if the toilet bottom fittings are loose and leaking due to long use, then glue and replace the fittings.

Precautions;

1. Before the installation of the toilet, you should check the levelness of the sewage pipe and the ground, check whether there is any blockage of sediment, waste paper and other debris in the pipe, and also check whether the ground is horizontal before and after the installation of the toilet.

2. Confirm the center of the sewage pipe, the confirmation method is to turn the toilet over, and then determine the center on the sewage outlet of the toilet, and at the same time draw a cross center line at the center, and the cross center line should extend to the bottom of the toilet and the feet around it.

3. First align the cross line between the toilet bowl and the ground sewage outlet, and then ensure that the toilet is installed horizontally, and then press the sealing ring tightly, and then you can install the screws and decorative caps of the anchors.

There is a leak around the bottom of the toilet, first overhaul the following aspects:

1. Check whether the outer wall of the toilet is damaged, which may lead to rupture and leakage.

2. Check whether there is any problem with the pumping and incoming and outgoing water of the water tank, and sometimes the old parts of the water tank will also lead to water leakage.

3. Know the original toilet installation method, there are two ways to install the toilet, one is to directly seal and fix the bottom with glass glue, and the other is to fix the bottom of the toilet with white cement, so that different toilet installation methods will directly lead to the stability of the toilet, and not stable enough will also cause water leakage.

4. When the toilet is installed, the toilet drain port needs to be closely connected with the ground sewage outlet, otherwise it is easy to cause water leakage, and a sealing flange ring needs to be installed for professional installation.

Maintenance method: see whether the inner wall of the internal toilet is broken, if there is a crack, it can be repaired directly with sealing glass glue, and check whether the toilet sealing flange ring is installed, and if it is not installed, it will be reinstalled. Inspect the toilet bowl and update the spare parts if the toilet has aging problems. If the toilet is loose and the internal drain is not tightly connected, the toilet can be re-sealed.

Toilet base leaking toilet, 90% of the toilet base is fixed with glass glue, which shows that the method of using glass glue to install the toilet is not adoptable, in the past, the toilet was installed with cement mortar, there is very little leakage at the bottom of the toilet, even if there is a leak at the bottom of the toilet, if you don't feel dirty, you can mix some cement mortar yourself, and touch some cement mortar at the bottom of the toilet to block it, but if the toilet is installed at the bottom of the toilet bowl fixed with glass glue, the bottom of the toilet will leak. The only correct solution is: move the toilet from its original position to the side, vacate the original toilet place, and then remove the old glass glue on the ground, wipe the water dry, and remove the old glass glue at the bottom of the toilet, wipe the water dry, these are the preparations that must be done, and then it is the same as the steps of installing a new toilet, the above process is the method of dealing with the leakage at the bottom of the toilet, doing this kind of work is more troublesome than the new toilet, and it is dirty, We often see some customers take the glass glue and touch the leaky area, which does not solve the problem at all.

The bottom of the toilet leaks water, generally speaking, it is the leakage of the metal hose and the toilet connection, the main reason is that the metal hose bursts and then the metal hose and the toilet connection leakage, so it is necessary to replace the metal hose in time. This is that if there is a leak in the place where the metal hose is connected to the toilet, it will need to be glued with some glass glue, if it is too little and too thin, there will be gaps in long-term use. Therefore, in the case of a joint, it takes 24-48 hours and do not use the toilet.

In the past, the toilet was installed with cement mortar, and there was very little leakage at the bottom of the toilet, even if there was a leak at the bottom of the toilet, you could mix some cement mortar, and touch some cement mortar at the bottom of the toilet to block it.

However, if the bottom of the toilet is fixed with glass glue when installing the toilet, and the bottom of the toilet is about to leak, the only solution is to move the toilet from its original position to the side, and then remove the old glass glue from the ground and wipe it dry, and the old glass glue at the bottom of the toilet bowl should also be removed, and the water will be wiped dry, and then the steps are the same as installing a new toilet.

The bottom of the toilet leaks water, it may be a leak in the place where the metal hose and the toilet are connected, and it needs to be glued with some glass glue, it takes 24-48 hours, do not use the toilet.

The above process is how to deal with a leak at the bottom of the toilet.

If there is a problem, it needs to be removed and cleaned and replaced, if it is still leaking, it needs to be replaced with a new scoop. If the scoop is fine, see whether the rubber pad at the sink hose interface is aging, and replace it with a new rubber pad in time.

1. The toilet seat is very clean around it, and there are a lot of bacteria left, which is due to the fact that when flushing the toilet, it will cause the stains in the toilet bowl to splash on the toilet seat.

2. After the toilet is used, it needs to be flushed to dispose of the internal excrement, and if there are yellow spots left in the toilet, you must brush it off with a brush, otherwise after a long time, the yellow spots will solidify, and it will become very troublesome to clean up. Also, be sure to close the lid of the toilet bowl when flushing.

3. Around the toilet, it is generally necessary to place a garbage can, so that the waste paper used daily can be thrown into the trash can, which can effectively place the toilet to be blocked. However, we must develop a good habit of cleaning out the bags in the trash can every day, otherwise it is easy to breed bacteria, which will affect the use.

Earlier fixed toilets were generally fixed with expansion studs, sealed with putty putty Now due to the presence of silicone, so many toilet installations are omitted to be fixed with expansion bolts, directly fixed with strong adhesive silicone and sealed with putty for a long time, will harden and cause cracking and leakage, if the silicone is not fully cleaned before bonding, it is also easy to produce local leakage If it is determined that the toilet is not cracked, then as long as the dirty things at the bottom of the toilet bowl and the floor tiles at the junction are removed, and wiped dry, and then play a circle of silicone sealing, Remember that you need to stop using the toilet for a night, if the bottom of the toilet is concrete, it will be troublesome, because often silicone is difficult to stick to the rough cement, so you need to redo the waterproof mortar to seal reliably.

The bottom of the toilet is leaking, don't be in a hurry, you should carefully check the cause of the leak. Deal with it accordingly. Once you know the cause of the leak at the bottom of the toilet, you can prevent and repair it in a targeted manner.

The owner friend can completely solve the problem by doing it himself. First of all, the owner friend should check whether the installation position of the parts in the tank is accurate, and if there is a loose place, it should be reinforced to make it tight. Glass glue is a more rational tool for closing the gap of the toilet, whether it is on the part where the toilet is connected to the water tank, or in other places that need to be sealed, it can be used.

When sealing the toilet bowl with glass glue, it is best to open the main valve of the faucet first to avoid discovering water leakage.