What should I do if the hand pressed rotating mop barrel does not rotate and how to maintain it

When the hand-pressed rotary mop is used for a period of time, it is often not timely to return to the position when using the pedal and throwing the barrel to rotate. In fact, this problem is mainly due to the friction between the mop ruler and both sides after a period of use, so our solution is to remove the ruler and flatten the teeth at the upper and rear ends of the ruler with a knife, so that the space between it and both sides can be effectively increased, and the problem can be well solved.

How to repair the mop barrel that doesn't turn:

1. The mop suddenly stopped rotating, we can rotate a knob in the middle of the mop, first loosen it in the counterclockwise direction, turn the lid on it, pull it down, and we can see that there is a white bolt. This is where the two rods connect, and the two rods are pulled apart in different directions to reveal the auger inside.

2. Pull the screw rod out of the rod, and after seeing that there is a gasket, take out the gasket, replace it with a new gasket of the same model, and install a new screw rod, which can solve the problem of not rotating.

3. It is also possible that because there are impurities in the spiral root, it will be stuck and cannot rotate normally. It is also possible that the spring is not flexible, and replacing it with a new spring and installing other parts can solve the problem.

4. If you still can't rotate, check the mop barrel, because after a long time, it is likely that there is any hair or paper scraps at the bearing that is blocked, and the bearing cannot rotate. Clean it up and you'll be able to fix the problem.

Introduction to the noun of mop:

A mop is a long-handled cleaning tool that scrubs the floor.

Mop, also known as a floor rag, refers to a long-handled cleaning tool for scrubbing the ground, and also refers to a long-handled cleaning tool in general. The mop should originate from a rag. In the most traditional mop, a bundle of strips of cloth is tied to one end of a long wooden pole.

Simple and inexpensive. The working head has been changed from a rag block to a bunch of cloth strips, which has a strong decontamination ability.

Whereas, the mop bucket is a tool used to hold the mop.

Spinning mop is not dehydrated how to repair pro, 1When turning the mop, if it does not dry up, then we need to open its pole first and adjust it. Then we can come and press the foot pedal, or press it with our hands.

Press four or five times is basically fine. 2.It may also be because there are some hairs adsorbed on the head of the handle, at this time there will be some static electricity, and then when the mop is dried, it will not dry the water, at this time we can buy a few more poles or cotton heads to replace the use.

3.Newly bought cotton head should be soaked in water first, and then placed in the sun to dry. In this way, in the future use, its water absorption and dehydration effect will be very good.

Hope it helps. If my answer is helpful to you, please give a thumbs up (in the lower left corner), I look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress. Finally, I wish you good health and a good mood!

Summary. Method: The key reason is that the friction part of the lower mop head and the disc is slipping, find the reason, and solve it: find a pin, straighten it (or the wire can also be used), burn it red on the fire, and burn some holes in the plastic disc at the friction site to increase the friction.

The hand-pressed barrel mop can't be rotated, how to repair it?

Method: The key reason is that the friction part of the lower mop head and the disc is slipping, find the reason, and solve it: find a pin, straighten it (or the wire can also be used), burn it red on the fire, and burn some holes in the plastic disc at the friction site to increase the friction.

It's not disc slipping. It is the foot pedal that does not reset! The spring doesn't move! Fold and develop a small piece of hard material to fall off! Is there a way to fix it?

Hello, this hard plastic is not easy to repair if it falls off, and it can't be used.

Unfortunately, it is recommended that you buy again, how much is one? Can I buy it from you?

Please reply. Hello, it is recommended to go to the local market to have a look, I am the answerer here, responsible for related questions! I hope you understand.

Okay, got it.

With the development of the times, the utensils have developed more and more advanced, just like the buckets we usually use to mop the floor, the traditional ones like the one before are no longer useful, and most people have begun to use this kind of rotationMop bucketThis kind of use is more convenient, but it is a little broken and I don't know how to fix it. Let me introduce it to youMop bucketHow to repair and how to use the hand-pressed rotary mop.

Mop bucketDo not turn how to repair.

Mop bucketThere are also two types of rotation. First of all, one is to rotate the pedal (active rotation), and the other is to rely on the spiral groove in the mop rod, which is relatively simple to use, as long as you press the linear motion up and down the mop rod to become a rotary motion, if you use the kind of foot pedal can rotate, then this is to see that there is no problem with your bucket, the bad is the mop rod, generally speaking, there is no way to repair this, then you can only change a new mop rod.

How to use the hand-pressed rotary mop.

1: How exactly do you combine mops?

In fact, the most important thing is to make oblique contact between the disc and the cloth disc, of course, there is also a way to lightly step on the disc from the other direction with one foot, and at this time you can hear the sound of clicking, which is almost a combination.

2: Sliding sleeve protection.

If it is when it is dehydrated, then this requirement requires you to strictly hold the slippery sleeve with one hand to fix the grip, so as to effectively protect the anti-slip and anti-wear effect of your hands, and at the same time, when you use it, there will be no rolling up and down.

3: How to update the cloth strip.

A better way is to step on the strip of cloth on the edge of the upper disc, which is the same direction as the screw, and then be sure to hold the mop tightly and push it in the opposite direction of the body, preferably to separate the disc from the disc.

4: How to adjust the angle:

The angle of the grip should also be controlled, generally speaking, it should be adjusted to 45 degrees, 90 degrees, 180 degrees, etc., and it must be carefully adjusted up and down according to the direction of the link.

5: Dry cleaning control.

The best thing is to do one foot up and down the pedal so that you can achieve rapid dehydration, this practice can be said to be safe and effortless, and at the same time the pair can also be very good decontamination, washing, of course, for drying is to have different needs, then at this time you have to adjust the length of time to design.

6: Pay attention to the highest water level.

I have to remind you that you must pay attention to the maximum water level at all times, so that when you use the water, there will be no overflow.

Summary: AboutMop bucketThe reason for the repair must be clarified, so that it is convenient for you to find its repair point, so that it is more convenient for you to repair.