Hand pressure rotary barrel mop can t turn how to repair

The maintenance method of the hand-pressed rotary barrel mop is as follows:

1.When the hand-pressed rotary mop is used for a period of time, it is often not timely to return to the position when using the pedal and throwing the barrel to rotate. In fact, this problem is mainly due to the friction between the mop ruler and both sides after a period of use, so our solution is to remove the ruler and flatten the teeth at the upper and rear ends of the ruler with a knife, so that the space between it and both sides can be effectively increased, and the problem can be well solved.

2.The second point of hand-pressed rotary mop maintenance is that when the mop pedal is installed, the foot pedal can be returned to its original position when the barrel is reversed, which is a problem that often occurs. This means that the one-way small bearing has been damaged or has been slipped, so it is very necessary to replace the matching bearing in order to solve it well.

3.If the barrel is turning, but the foot pedal cannot return to the original position, we have to consider whether the elastic tension of the spring is insufficient or the friction of the gear set is too large, and there are some situations of pinching and locking. Then our solution has two points, one is to buy a good matching spring for replacement.

The specific replacement method is as follows, first with a common screwdriver.

Remove the footpeg, followed by the removal of the red big gear with a hex buckle. Remove the ruler, and finally remove the damaged spring, and then install the new spring to the bayonet of the ruler from the new one.

4.For the installation of the ruler strip of the hand-pressed rotary mop, the specific operation steps are as follows. Attach the other end of the new spring to the other bayonet of the foot pedal with needle-nose pliers or other tools, and the last step is to install the gear.

The next step is to install the entire footpeg. The operation method of these two steps is very simple, as long as you see the structure clearly, you can install it along the vine.

The maintenance method of the hand-pressed rotary barrel mop is as follows:

Hand-pressed rotary mops should be well maintained so that the above problems do not occur often. When using the hand-pressed rotary mop, the water should be changed frequently, there should not be too many impurities, and it should be wrung out after washing and placed in a ventilated place; Don't over-twist the handle when rotating it, as it is easy to cause the handle to not return to its original position; After a period of use, the head of the hand-pressed rotary mop can be replaced, otherwise its cleaning function will be reduced.

The easiest way to do this is to contact the brand manufacturer you purchased directly and see if it can solve it for you!

You can simply see which aspect of the problem is first.

1. The dehydration basket does not rotate (you can try to rotate it by hand in the neutral state) 2. The washing pool does not rotate (you can try to rotate it by hand in the neutral state) 3. The mop rod does not rotate.

See what the problem is so that you can easily explain it to the manufacturer.

Good daughter-in-law wishes you a speedy solution to the problem. Have fun!

How to repair the mop barrel that doesn't turn:

1. The mop suddenly stopped rotating, we can rotate a knob in the middle of the mop, first loosen it in the counterclockwise direction, turn the lid on it, pull it down, and we can see that there is a white bolt. This is where the two rods connect, and the two rods are pulled apart in different directions to reveal the auger inside.

2. Pull the screw rod out of the rod, and after seeing that there is a gasket, take out the gasket, replace it with a new gasket of the same model, and install a new screw rod, which can solve the problem of not rotating.

3. It is also possible that because there are impurities in the spiral root, it will be stuck and cannot rotate normally. It is also possible that the spring is not flexible, and replacing it with a new spring and installing other parts can solve the problem.

4. If you still can't rotate, check the mop barrel, because after a long time, it is likely that there is any hair or paper scraps at the bearing that is blocked, and the bearing cannot rotate. Clean it up and you'll be able to fix the problem.

Introduction to the noun of mop:

A mop is a long-handled cleaning tool that scrubs the floor.

Mop, also known as a floor rag, refers to a long-handled cleaning tool for scrubbing the ground, and also refers to a long-handled cleaning tool in general. The mop should originate from a rag. In the most traditional mop, a bundle of strips of cloth is tied to one end of a long wooden pole.

Simple and inexpensive. The working head has been changed from a rag block to a bunch of cloth strips, which has a strong decontamination ability.

Whereas, the mop bucket is a tool used to hold the mop.

Summary. 1. The rotating mop barrel does not rotate, which may be because the return is not timely. Because the ruler of the rotating mop barrel has been used for a long time, it will cause friction with both sides.

We can use the screw to remove the foot pedal of the rotating mop barrel, and then use the hexagonal inner buckle to remove the red big gear, and then remove the ruler, use a knife to cut the six or seven teeth at the back end of the ruler slightly, and then reinstall it, or directly replace it with a new ruler.

2. If the rotating mop barrel is reversed, then it may be because the spring elastic tension of the rotating mop barrel is insufficient, we can remove the foot pedal, big gear, and ruler of the rotating mop barrel respectively, and then remove the damaged springs on the ruler bayonet, replace them with new springs, and then reinstall them.

How to repair the mopping bucket if it doesn't turn.

1. The rotating mop barrel does not rotate, which may be because the return is not timely. Because the ruler of the rotating mop barrel has been used for a long time, it will cause friction with both sides. We can use screws to remove the foot pedal of the rotating mop barrel, and then use the hexagonal inner buckle to remove the rotten gear of the red greenhouse, and then remove the ruler, use a knife to cut the six or seven teeth at the back end of the ruler slightly, and then reinstall it, or directly replace it with a new ruler.

2. If the rotating mop barrel is reversed, then it may be because the spring elastic tension of the rotating mop barrel is insufficient, we can remove the foot pedal, big gear, and ruler of the rotating mop barrel respectively, and then remove the damaged springs on the chain ridge ruler bayonet, replace them with new springs, and then reinstall them.

3. There is also a double-drive rotating mop barrel on the market, which does not have envy pedals, and generally drives the rotation of the mop barrel by pressing the mop rod by hand. In the process of use, if there is a situation that the rotating mop barrel does not turn, then it may be because of the built-in spring of the hand-pressed rod. For this reason, there is usually no brother Duan Xiangfa to repair, and only one mop pole can be replaced.

Hope it helps.

The repair and disassembly diagram of the rotating mop barrel without turning is as follows:

If the mop barrel does not rotate, there should be a problem with the rotating shaft inside. You can open the barrel to see if the steel balls in the empty groove are normal, and if the steel balls are worn out, they should be replaced with a new one.

It is also possible that the pedal spring of the mop barrel is not elastic enough, resulting in excessive friction and locking, you can remove the damaged spring and install the new spring on the bayonet of the ruler.

The solution to spin the mop itself does not turn:

Generally, the rotating mop is composed of two parts, there is an interface in the middle, if the mop itself does not rotate is a problem with the interface, use a hacksaw to split the middle into two sections, check whether there is a problem at the interface, and then check whether the nut on the disc is working normally, if there is damage, you can change a new nut, and then install the mop head.

There is also a possibility that the mop ruler will have friction with both sides after using it for a period of time, resulting in the inability to rotate, the solution is to remove the ruler and flatten the teeth at the upper and rear ends of the ruler with a knife to increase the space on both sides without friction.

The method of changing the head of the mop is as follows:

First of all, put the rotating mop pendulum rock dust on the flat ground, firmly step on the board surface with your feet, and turn as close to the metal part as possible. Then hold the handle of the mop with your left hand, rotate the base part counterclockwise, and when you hear a "click", it means that the handle of the mop and the head are separated, and then you can remove the old mop head.

Then clean the mop handle with water and steel wool balls, prepare the new mop head to lay flat on the ground, and rotate the mop handle clockwise towards the center of the head, which also produces a "click" sound, which means that the installation is completed. Finally, lift the mop and observe it carefully to see if the mop head and the mop handle are completely consistent, and if you can, you can use it normally.

Rotate the mop to spin the dry barrel without turning the maintenance method: the ruler needs to be repaired due to the untimely return, and the mop rod needs to be replaced for the built-in spring problem of the hand pressure bar.

1. It may be caused by untimely return. The reason for this phenomenon may be that the ruler of the rotating mop bucket has been used for a long time and friction has occurred on both sides.

I can use a screwdriver to remove the foot pedal of the rotating mop bucket, and then use the hexagonal inner buckle to remove the red big gear, and then remove the ruler, use a knife to cut the six or seven teeth at the back end of the ruler slightly, and then reinstall it, or directly replace it with a new ruler.

2. There is also a double-drive rotating mop barrel, which generally drives the rotation of the mop barrel by pressing the mop rod by hand. If the rotating mop barrel does not rotate, it may be that there is a problem with the built-in spring of the hand-pressed pole. If it is caused by this reason, it is usually impossible to repair and there is an option to replace a mop pole.

Maintenance of the swivel mop

1. After use, it must be scrubbed and wrung out, and placed in a ventilated place to avoid odor and odor.

2. When the mop has a peculiar smell, you can use diluted bleach to clean the mop.

3. When the hair on the mop sticks, you can use a brush to help remove it, or wait for it to dry before sticking it off with tape.

4. In order to keep the home clean and hygienic, it is recommended to replace the mop head every two to three months.

5. Use with detergent, the amount should not be too much, otherwise it is easy to remain and affect the service life of the mop.

Summary. Method: The key reason is that the friction part of the lower mop head and the disc is slipping, find the reason, and solve it: find a pin, straighten it (or the wire can also be used), burn it red on the fire, and burn some holes in the plastic disc at the friction site to increase the friction.

Hand pressure rotary barrel mop can't turn how to repair

Method: The key reason is that the friction part of the lower mop head and the disc is slipping, find the reason, and solve it: find a pin, straighten it (or the wire can also be used), burn it red on the fire, and burn some holes in the plastic disc at the friction site to increase the friction.

It's not disc slipping. It is the foot pedal that does not reset! The spring doesn't move! Fold and develop a small piece of hard material to fall off! Is there a way to fix it?

Hello, this hard plastic is not easy to repair if it falls off, and it can't be used.

Unfortunately, it is recommended that you buy again, how much is one? Can I buy it from you?

Please reply. Hello, it is recommended to go to the local market to have a look, I am the answerer here, responsible for related questions! I hope you understand.

Okay, got it.

There are also two ways to rotate the mop bucket. First of all, one is to rotate the pedal (active rotation), and the other is to rely on the spiral groove in the mop rod, which is relatively simple to use, as long as the linear motion up and down the mop rod is pressed to become a rotary motion.

If you use the kind of foot pedal that can rotate, then this kind of is to see that there is no problem with your bucket, and the bad is the mop lever, generally speaking, there is no way to fix this, then you can only replace it with a new mop lever.