Under what circumstances will the pulse electronic fence give an alarm

There are three commonly used types of pulse electronic fences: short circuit, open circuit, catenary and bypass.

Short circuit alarm: 2 adjacent conductor paths;

Broken circuit alarm: any wire is broken;

Touching the net: any wire is touched by the human body;

Bypass: Any one of the wires is touched by a conductor.

In the case of the above four situations, the host will output an alarm signal, and then the alarm system will respond and remind the nearby security personnel to deal with it in time.

Pulse electronic fence.

The difference is huge.

First of all, in principle, the pulse electronic fence, the alloy wire transmits a high-voltage pulse signal; Tension electronic fence, alloy wire is not electrified.

Functionally, the pulsed electronic fence will give people an electric shock in some cases, and it is good to do it, such as the pulsed electronic fence of Elion, as long as it is working normally, once the hand or other parts touch the alloy wire, it will be shocked, and at the same time alarm the system. Others are relatively poor, only under certain circumstances will be electrified, and there will be no alarm, but rest assured, high voltage and low power are usually not too dangerous. So it is a little more deterrent than the tension electronic fence.

Tension electronic fence is not necessarily, although it can play a certain role in blocking and deterring, but compared with pulse electronic fence, because it itself is not charged, so the deterrent effect will be slightly worse. Its role is mainly in detection. When an intrusion occurs, the pulsed electronic fence will not necessarily alarm (with the exception of the Arian drift and bright pulsed electronic fence), but the tension fence will definitely alarm and there will be basically zero false alarms.

In terms of safety, tension electronic fences are higher than pulse electronic fences.

In terms of **, the tension electronic fence is higher than the pulse electronic fence.

Others are checked on the Internet.

First of all, check the keyboard or the indicator light of the electronic fence host, and see what alarm the keyboard or indicator light prompts (short circuit, open circuit, disconnection, etc.). According to the above alarm prompts, check the external network and wiring at the front end of the electronic fence, check whether there is any abnormal situation on the external network, and eliminate abnormal conditions if so. Then re-enter the password via the keypad to arm it.

List of functions of the pulsed electronic fence:

LCD liquid crystal display real coarse and electric wisdom rotten voltage value;

It has a remote stool leakage control keyboard;

The host has the function of setting permissions to prevent irrelevant personnel from operating;

Each fence at the front end has an impulse voltage;

It has the function of switching between high and low voltage;

It has a battery access interface;

It has the function of alarm partition;

Pulse electronic fence host LCD LCD display effect:

Summary. Dear Hello, I am happy to answer for you, the following is the answer for your query, I hope it will help you: Pulse electronic fence as an anti-theft measure, there may be a variety of faults in use, common faults and their troubleshooting methods are as follows:

1.Alarm not sounding: This may be caused by poor contact of wires on the fence or faulty alarm.

You can check if the wire connection is secure, and if the connection is normal, you need to replace the alarm. 2.The alarm goes off all the time:

This can be caused by a short circuit in the wires on the fence or a faulty alarm. You can check whether the wire connection is normal, and if the connection is normal, you need to replace the alarm. 3.

Fence alarm, but no one touches it: This can be caused by external interference or electromagnetic interference on the wires on the fence. It is possible to check the surrounding environment for electromagnetic interference sources, such as high-voltage power lines, TV towers, etc.

If the source of interference cannot be eliminated, the material and construction of the fence wires need to be replaced. 4.Fence recovery after alarm:

This can be due to poor wire contact on the fence or a faulty alarm. You can check if the wire connection is secure, and if the connection is normal, you need to replace the alarm.

Hello, I'm glad to answer for you, the following is the answer for your query, I hope it will help you: Pulse electronic fence as an anti-theft measure, there may be a variety of faults in use, common rush faults and their troubleshooting methods are as follows:1

Alarm not sounding: This may be caused by poor contact of the wires on the fence or a faulty alarm. You can check if the wire connection is secure, and if the connection is normal, you need to replace the alarm.

2.The alarm keeps ringing: This may be caused by a short circuit in the wires on the fence or a faulty alarm.

You can check whether the wire connection is normal, and if the connection is normal, you need to replace the alarm. 3.The fence alarmed, but no one touched it:

This can be caused by external interference or electromagnetic interference on the wires on the fence. You can check the surrounding environment for electromagnetic interference sources, such as high-voltage power lines, TV towers, etc. If the source of interference cannot be eliminated, the material and construction of the fence wires need to be replaced.

4.Self-recovery after fence alarm: This can be caused by poor wire contact on the fence or faulty alarm.

You can check if the wire connection is secure, and if the connection is normal, you need to replace the alarm.

It should be noted that for the maintenance and troubleshooting of the pulse electronic fence, it is recommended to ask a professional to operate. Under normal circumstances, it is necessary to pay attention to the use of rough attention, regularly check the wire connection of the fence and the working state of the alarm, and find and solve the fault in time.

Summary. Hello pro thought that for your inquiry, the pulse indicator light of the electronic fence host has been on and not flashing, and there may be the following reasons for no pulse output: 1

Power failure: The electronic fence host needs a stable power supply**, if the power supply voltage is unstable or the power line is not in good contact, it may cause the pulse indicator to be on and not flashing, and there is no pulse output. The solution is to check whether the power supply line is in good contact and whether the power supply is output normally.

2.Electronic fence line failure: The electronic fence line fault may cause the pulse indicator to be on and not flashing all the time, and there is no pulse output.

The solution is to check whether the electronic fence line is in good contact and whether the line is damaged. 3.E-fence controller failure:

A malfunction of the electronic fence controller may result in the pulse indicator light remaining on and not flashing, and there is no pulse output. The workaround is to check if the controller is working properly and if there is a fault. 4.

Faulty electronic fence sensor: A faulty electronic fence sensor may cause the pulse indicator to remain on and not flashing, and there is no pulse output. The solution is to check if the sensor is working properly and if there is a fault.

5.Ground fault: A ground fault may cause the pulse indicator to remain on and not flashing, and there is no pulse output.

The solution is to check if the ground wire is in good contact and if there is any damage. If the above methods cannot solve the problem, it is recommended to contact a professional technician for repair. Hope mine is helpful to you.

Hello. The pulse indicator of the electronic fence host has been on and not flashing, and there is no pulse output, what's going on.

Back. Receive an inquiry for you right away.

The pulse output is off.

Back. Hello pro thought that for your inquiry, the pulse indicator light of the electronic fence host has been on and not flashing, and there may be the following reasons for no pulse output: 1

Power failure: The electronic fence host needs a stable power supply**, if the power supply voltage is unstable or the power line is not in good contact, it may cause the pulse indicator to be on and not flashing, and there is no pulse output. The solution is to check whether the power supply line is in good contact and whether the power supply is output normally.

2.Electronic fence line failure: The electronic fence line fault may cause the pulse indicator to be on and not flashing all the time, and there is no pulse output.

The solution is to check whether the electronic fence line is in good contact and whether the line is damaged. 3.E-fence controller failure:

A malfunction of the electronic fence controller may result in the pulse indicator light remaining on and not flashing, and there is no pulse output. The workaround is to check if the controller is working properly and if there is a fault. 4.

Fault of the electronic fence sensor sensor: A failure of the electronic fence sensor may cause the pulse indicator to remain on and not flashing, and there is no pulse output. The solution is to check if the sensor is working properly and if there is a fault.

5.Ground fault: A ground fault may cause the pulse indicator to remain on and not flashing, and there is no buried pulse output.

The solution is to check if the ground wire is in good contact and if there is any damage. If the above methods do not solve the problem, it is recommended to contact a professional technical personnel for repair. Hope mine is helpful to you.

The pro message was sent to you, you see.

Dear, hello, let you wait for a long time, I am happy to answer for you, pulse electronic fence is a kind of hail commonly used security equipment, if there is a failure, it will affect its normal operation. Here are some common faults and how to troubleshoot them:1

Alarm no response: check whether the power supply of the alarm is connected normally, check whether the output signal of the host is normal, and check whether the alarm line is in good contact. 2.

Power failure: Check whether the power supply line is in good contact, check whether the power switch is normal, and check whether the power supply is normal. 3.

Unstable pulse current: check whether the power supply is normal, check whether the current regulating potentiometer is loose, and check whether the line is in good contact with the source. 4.

Line fault: Check whether the line is in good contact and check whether the line is damaged or damaged. 5.

Bad ground wire: Check if the ground wire is well grounded, check if the ground wire is damaged or damaged. 6.

Sensor failure: Check if the sensor is damaged or damaged, check if the sensor is in good contact, check if the sensor has been disassembled or changed position. 7.

Lightning protection failure: check whether the lightning protector is working normally, and check whether the lightning protector is damaged or damaged. The above are the common faults of the pulse electronic fence and their troubleshooting methods, if you can't solve it by yourself, it is recommended that Iwaju contact professional security maintenance personnel for maintenance.

1. A multi-zone host can control 1-16 zones through 1-16 zone detectors at the same time.

2. It has a complete and clearly demarcated electronic fence, which has a strong blocking and deterrent effect.

3. It has the intelligent alarm function with a very low false alarm rate, when a case occurs at the front end of a defense area, the intelligent defense area host can quickly display the network disconnection, short circuit, and network contact alarm in the display window, reflecting the front-end status.

4. It is equipped with alarm interface and switch signal output, which can be linked with other security systems to improve the safety level of the system.

5. Detection function - the electronic fence can monitor the level of various intrusions, and has the ability to distinguish accidental intrusions or forcible intruders.

The electronic fence has the functions of blocking, deterrence and alarm, low false alarm rate (not affected by weather, small animals, branches, etc.), simple installation, long service life, low comprehensive cost and other advantages; It can be widely used in: residential areas, villas, schools, factories, zoos, orchards, substations, prison detention centers, military bases, first-class institutions, key cultural relics sites, borders, residential areas, industrial land, storage land, breeding and planting parks and other places that need to be isolated and protected.

Pulse electronic fence alarm system for industrial parks.

Electronic fencing. Impulse voltages are divided into high voltage and low voltage; In high voltage mode, the impulse voltage is between 5000V and 10000V, and the electronic fence impulse voltage is similar to a sinusoidal curve.

Again, the voltage value is constantly changing. Its duration is, that is, there is a peak, an interval of one time. In low-voltage mode, the impulse voltage is 700V-1000V.

The switching between the high and low voltage of the electronic fence can be operated by the keyboard, computer software or the switch button on the electronic fence host, which is very convenient.