How to install the water pipe of the water softener, the installation of the household water softene

1.The installation surface of the water softener should be firm and sturdy, and its bearing capacity should not be less than twice the weight of the water softener, and at least not less than 80kg. At the same time, the installation pipeline layout, noise, ambient temperature and other requirements of the water softener should be considered.

2.Measure tap water pressure, suitable range: Use a pressure gauge to measure the pressure of the tap water, and if it is lower or higher than the specified pressure, a booster pump or pressure reducing valve needs to be installed to ensure the normal operation of the equipment.

3.Detect the hardness of raw water, measure the PPM value of raw water with a TDS pen, or monitor the hardness of water quality by other means.

4.Installation of overflow pipes and drain pipes.

The overflow and sewage nozzle should leave a 10cm gap above the sewage pipe or floor drain, and do not directly insert the overflow and sewage pipe into the sewer pipe or floor drain to produce a siphon phenomenon, and the sewage is sucked into the water softener and cause damage.

5.Piping installation.

First, the gasket is fitted into the two bellows interfaces; The bellows are tightened at the inlet and outlet of the water pipeline bypass system, and the connection height of the other two ports of the bellows is adjusted with the inlet and outlet of the bypass valve of the water softener. Insert the gasket, connect it to the inlet and outlet of the bypass valve of the water softener, tighten it and connect the bypass valve.

6.Move the water softener to a suitable position, secure the device, and connect the power supply.

7.Parameter settings (display panel interface).

The control valve used in the water softener product is set in the front and back mode: the front desk mode is suitable for the user, sets the current time, the regeneration initiation time (the default value is 2:00), the raw water hardness value input (the hardness value measured in step 3) and displays the operating water supply and other parameters.

The background mode setting does not need to be set by the user himself.

8.The water softener is debugged, the resin tank air is emptied, and the resin is rinsed until there is no black water and yellow water flows out.

9.Add special salt for regeneration to the salt tank, and prohibit the use of salts containing additives or coarse salts with large crystalline particles. The salt surface should reach the height of the salt box above 2 3 (do not exceed the height of the overflow port), and add the required amount of saturated salt water at one time.

1. The water softener is a product of PoE, that is, it is to be installed on the main pipe.

2. The installation location should be rainproof, anti-freezing, with power supply and floor drain.

3. Some models can be placed in the cabinet, but be sure to leave space for cleaning and maintenance with salt (consumables) in the future.

4. For the model placed in the cabinet, the service provider must communicate with the cabinet company.

5. There are many particularities in pipeline design, such as the faucet pipeline for cleaning the mop, the pipeline of the water purifier, the pipeline of the water heater, etc., which must be designed in advance.

6. If you buy"Whole home solutions", the combination order between different products, the size of the pipe diameter, and the flow rate during selection are all details to be considered.

7. If you want to add a booster pump, you should also consider the cooperation between the two depending on the type of water treatment product.

It is important to know that soft water and tap water are very different in terms of taste and feel. So, nowadays, more and more people are using water softeners at home so that you can drink healthier and tastier water. However, some people find that the water softener is not installed at home, before installing, let's take a look at the installation of the household water softener.

Next, it's up to us to bring it to youWater softener installationLet's find out the steps together.

Household water softener installation steps:

1.When importing the water softener, ask the owner to confirm whether the machine is in good condition. When the standard product water softener is delivered, the source leaks, and the strap on the outer packaging is fastened with a plastic buckle.

2.After opening the package, the installer will explain the functional characteristics of some products to the owner, so that the owner knows how to handle the water and use it with confidence.

3.Connect the water inlet pipe of the water purifier. Since the household water purifier and water softener are installed together, the water pipe is divided into two roads, which are connected to the water softener for soft water.

4.Temporarily connect the water pipe next to the water purifier to drain the sewage that needs to be removed when flushing the inside of the water purifier. Because it's a new machine, there are some residual impurities in it that can be easily overlooked.

5.Generally, the water softener can be set to flush every 12 hours on the computer board for about 30 seconds each time, but when it is debugged, because it is a new machine, it needs to be cleaned for about half an hour.

6.Clean the nozzle of the water softener into the socket. Because the water pipes are installed first, there will inevitably be some dust outside. If it's not a regular installation team, it's usually overlooked.

7.It is worth mentioning that the installer should use white tape to wrap several times around the connection of each nozzle, paying attention to leakage and bacteria.

8.When debugging a water softener, first turn the computer screen on the machine. Because of the fear that it will be broken during shipping, it will be turned upside down at the time of delivery. The location of the connection between the computer screen and the fuselage is active and does not affect the normal use of the machine.

9.Once the water softener is installed, pour salt into it. The salt used in the water softener is a special salt that is imported. The damage to the machine and water quality is relatively small, and the shape is a bit like a cockroach pill.

The water softener is most suitable for installation.

Kitchen installation. The water softener is installed in the kitchen. The most desirable location is a cupboard basin.

This is by far the most common installation plan. However, this solution has certain requirements for the size of the water softener. It is advisable to give preference to splitting machines.

A machine usually needs to be individually designed to store the cabinets. Consumers can also easily choose kitchens and cabinets with sizes and inches. If it is installed outside the cabinet or as a cabinet alone, the cost is also high, and it is also necessary to consider the pipe orientation of the water pipe, the return pipe, the sewage pipe (the pipe is always inconvenient).

Bathroom installation. The footprint of the enclosure is usually small. There is very little space available for basic decorations.

The volume of water softeners on the market is relatively large. Therefore, it is best to install a split water softener in the bathroom. Ideal if it is installed in a washbasin cabinet.

Otherwise, bare metal installation becomes a must, but you can also consider hanging it on the wall (a bit of a ** view).

Tap water contains some unhealthy substances to the body, such as chloride ions, bleaching powder, etc., the water softener can just remove the calcium and magnesium ions in the tap water, and can also reduce the hardness of the water. Let's take a look.

1. Household water softener - installation.

1. When the water softener is delivered, we should first confirm the situation of the water softener to see if the machine is intact.

2. After the package is opened, the installer will give us some explanations to tell us what functions the bulldozing has, so that consumers can know how the water is processed, so that consumers can rest assured that they can use it.

3. Connect the water inlet pipe on the water purifier, because the water purifier and the water softener are installed together, so the water pipe will be divided into two ways, which are connected to the water purifier and the water softener respectively.

4. There will be a water connection pipe next to the water purifier, which is used to release the sewage discharged from the inside of the water purifier, and the new machine will have the previous residual impurities that are easy to be ignored.

5. The water softener should be set to flush every 12 hours, and the time of each flushing should be about 30 seconds, and the first flushing time of the new machine should be designed to be about 30 seconds.

6. The water pipe has been installed in advance, and we should clean it once, because it will inevitably be loaded with dust, if it is not a regular installation team, this will usually be forgotten. If you see the installers wrapping their white feet around the joints between the gates, they are doing a lot of leak prevention and sterilization measures.

7. When the water softener is debugged, the display screen on the machine should be turned in a different direction, so that it can avoid being damaged during transportation, so it is extremely reversed when it is sent, and the body linking the display screen is flexible and will not affect the use of the machine.

8. After the water softener is installed, some salt should be poured into it, the salt used in the water softener is imported for special use, and the damage to the machine and water quality is very small.

2. Household water softener.

1. Honeywell.

Founded in 1885, it is a leader in diversified manufacturing technologies whose purpose is to achieve mutually beneficial growth by increasing comfort, productivity, energy saving, protecting the environment and protecting the lives and property of users, satisfying customers and striving to become the world's pioneer in self-control.

2. Midea

Founded in 1968, it now has more than 200 subsidiaries, their mission is to create a better life for consumption, Midea was established for so many years, has been loved by many consumers, can be said to be the most used household appliance brand.

1. Hold the connector on the washing machine with one hand, and pull down the buckle with the other hand to separate the connector from the water inlet pipe.

2. Unscrew the 4 screws on the connector used above, and unscrew the connector so that the size of the 3 threads is retained between the two connectors.

3. We need to evenly allocate the 4 screws of the inlet pipe connector to keep the 2 screws on the inside fully connected to the faucet. The screws on the inside can be kept at a relatively loose distance.

4. Without taking out the sealing ring and keeping the faucet flat, connect the connector facing upwards to the faucet, so that the internal sealing ring and the faucet are fully connected.

5. Keep the 2 screws on the inside in contact with the faucet, and then tighten it.

6. Go back and carefully check whether there is still water leakage, if there is still water leakage, you only need to reinstall it according to the original steps. Also, remember to use a standard faucet, otherwise deviations may occur.