I just changed the wiper link, and now the wiper on the cab side often hits the side

Hello. This has something to do with the fact that the replacement wiper link is not adjusted properly.

The wiper link to the motor is not well adjusted. Adjust the method correctly, turn on the wiper motor, work for one cycle and then turn it off.

At this time, the motor is in the return state, loosen the wiper connecting rod screw, and adjust the wiper arm to the lowest position. Tighten the connecting rod nut.

Pay attention to check whether the left and right wiper blades are reversed, and whether the wiper blade nuts are tightened.

Hello, are you replacing the left and right sides of the wiper upside down, generally the wiper on the left side is longer.

This is caused by the fact that the angle and relative position of the landlord did not grasp the wiper connecting rod when replacing it, and it can only continue to be adjusted.

This is when the linkage rod is installed, the position and motor are not adjusted properly!

Hello, according to your fault description, it is recommended to go to the repair station to adjust the position of the left front wiper arm, and reinstall the wiper arm to eliminate the fault. Have a nice ride, thank you.

Hello, in this case, it is best to ask a professional master to help adjust the wipers, basically there is no problem.

There may still be some problems with the adjustment, and the adjustment should not be adjusted to the minimum, and it may need to be reinstalled and adjusted.

In this case, you have to go to the maintenance shop and ask the master to help adjust the wiper operating lever, and you can't adjust it if you have no experience.

It seems that in this situation you definitely need to adjust it up rather than down, which is mainly caused by improper adjustment.

Mine is also this problem, how do you solve it.

Hello, this should be an installation problem or the left and right connecting rods are reversed, you can reinstall it.

The two wipers of the car touch together and can be adjusted by the screws on the wiper arm holder. The wiper is mainly opened on the wiper lever on the right back of the steering wheel, and the front wiper speed adjustment and washing liquid spray can also be adjusted.

Wipers, also known as wipers, water picks, wipers or windshield wipers, are equipment used to brush and scrape rain and dust attached to the windshield of vehicles to improve the visibility of drivers and increase driving safety. Wiper control system, through the electronic control system, can not only realize the delay control of the wiper, but also can realize some other complex control. The electronic control system consists of a two-speed motor and two limit switches, through which the following functions can be achieved through a handle switch:

Washing, wiping, high-speed wiping, low-speed wiping, intermittent wiping, and delay control. The sophisticated electronic control system also enables positive pressure control of the swing bar and rain sensing control.

The wiper tightening adjustment method is as follows.

When the car is powered on, move the wiper to the closest edge of the glass and turn off the power.

Open the hood, loosen the left wiper screw, move it to a good position, pinch the screw, and then power it will automatically return to the bottom, but it will be exposed.

At this time, loosen the right wiper screw, push the left wiper firmly to the hidden place, and then pinch the screw tightly.

The position is adjusted, dial the bottom of the windshield [If you have a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

What happens when the car two wipers work against each other.

It may be that the motor of the wiper is damaged, and it should be okay to replace it.

Car wiper tight, how to adjust.

1. Method: 1. When the car is powered on, move the wiper to the edge closest to the glass and turn off the power. 2. Open the hood and loosen the left wiper screw, move it to the correct position and pinch the screw, and then power it will automatically return to the bottom

How to adjust the car wiper when it is overdone.

Remove the cover of the wiper shaft head, the screws will be exposed, loosen the screws and twist the wiper arm back a little.

How do you maintain a car wiper? What should I do if I encounter a "jump brush"?

Keep the sheet and glass clean, do not dry scrape, the motor part has to be buttered for a long time, the jump brush may be aging and hard, or it is a mechanical failure, if the number of times is less and return to normal to replace the piece will be fine [There is a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

Car wipers can't be parked in the right place, how to adjust.

Hello. The first thing to do is to get the motor fixing screws of the wipers open. Then turn the motor idling for one turn until it stops automatically.

Then the bracket of the wiper motor is basically the initial position. There will be no stopping in the wrong place. If the deviation table is not large, you can also unscrew the fixing screw of the wiper arm to adjust the position slightly, I hope to help you, I wish you a happy car!

1.When the car is powered on, first move the wiper to the edge closest to the glass, and then power off;

2.Open the engine cover, loosen the left wiper screw, move it to a good position, tighten the screw, and then it will automatically go back to the lowest part when the power is on, but a part will be exposed;

3.At this point, loosen the right wiper screw, firmly push the left wiper into hiding, and tighten the screw.

Hello, generally speaking, the wiper blades will not touch together, it should be that the wiper link rod is damaged or the wiper electronics is not working properly, it is recommended to go to the repair shop or 4S shop to check, I hope to help you, hope to adopt, thank you.

Hello, the wiper blade can not be sided, it may be that the wiper blade is loose or not adjusted well, you need to release the wiper arm to adjust the wiper blade to the position of the upper point to install it, I hope it will help you.

This kind of wiper should be too long for you to buy, replace one of the wipers with a shorter one, this kind of wiper will generally appear in the opposite movement of the wiper when you buy the wiper to pay attention to the length.

Summary. Hello, don't worry, I can ask for your question, but wait a minute, I need text for about 2 minutes.

Hello, don't worry, I can ask for your question, but wait a minute, I need text for about 2 minutes.

In this kind of dry situation, first of all, you need to check whether there is a problem with the linkage rod, if you say that the reputation here is normal, there is no problem, then you need to readjust the position.

The rain wiper itself is normal, and the rain wiper is normal to put it down, and the two wipers will touch.

The wiper is scraped normally, that is, it is put down and touched by the wiper together.

So, you need to adjust it a little bit and just make it a little bit higher.

Okay, I'll go to the repair shop tomorrow and transfer it.

When the car is used for a period of time, it is inevitable that there will be some small problems, and the next thing to talk about is how to change the position of the wiper linkage lever? Note that it must be replaced after the car is turned off, first remove the old rain scraper, place the new one at the lowest point of the windshield, align the wiper spindle, and fix it with a nut.

Steps to replace the wipers

1. Take down the old wipers. Pull out the arm of the wiper, so that the wiper is in a standing state, there will be a square opening in the middle, press the plastic block inside, and the other hand will go up, you can pull the wiper out.

2. Remove the adhesive strip of the wiper. When the wipers are removed, you can see that there will be a plastic cap at each end. One is fixed and the other is movable.

Use a screwdriver to pry open the fixed cap, open another metal buckle, and gently pry it open with a screw crack and drain knife, and the adhesive strip can be pulled out.

3. Change the rubber strip with a new one, insert the rubber strip in the wiper groove, buckle tightly, and don't forget to cover the plastic cap.

4. It is best to install a new wiper, which is just the opposite of the first step, align the small hole in the boom, and then clamp it to complete the installation.

Summary. Hello, I am happy to answer your car master exclusive technician to answer your car questions sincerely and sincerely for you, and find solutions and methods for you to ask questions. The inconsistent response speed on both sides of the windshield wiper lever is caused by a loose tie rod fixing screw, or a damaged tie rod mechanism.

You can first check whether the fixing screws of the wiper adjustment arm are loose, and the tightness of the screws is normal, that is, the connecting rod mechanism is damaged. Need to replace the whole linkage, hope mine is helpful to you.

Hello, happy to answer your questions.

Hello, I am glad that Lu Zhao will answer your car master exclusive technician for you to concentrate on your car and sincerely answer your car questions, and find solutions and methods for you to ask questions. The inconsistent response speed on both sides of the windshield wiper lever is caused by the loosening of the tie rod fixing screws or the damage to the tie rod mechanism. You can first check whether the fixing screws of the adjusting arm of the Yuchang Xi roller brush are loose, and the tightness of the screws is normal, that is, the connecting rod mechanism is damaged.

Need to replace the whole linkage, hope mine is helpful to you.

Pacific Automobile Network] The wiper connecting rod falls off and only needs to be replaced with a new connecting rod. Windshield wipers are divided into front windshield wipers and rear windshield wipers. Depending on the drive device, there are three types of wipers: vacuum, pneumatic and electric.

Electric wipers are widely used in vehicles at present.

Car wipers are prone to breakdown, whether they are used often or not used for a long time, which is determined by the characteristics of car wipers. Because the car wiper is exposed to the outside of the car regardless of wind, rain or sun, because the car wiper hall is made of rubber, it is easy to age after long-term exposure, and it is easy to have a car wiper failure because of the bright age. Therefore, the driver must use and maintain the wiper correctly, and repair the wiper in time if it is found that the wiper is faulty.

In order to maintain a good line of sight when driving in rain and fog, drive safely.

Wiper sound treatment method:

1. The wiper blade is abnormal noise caused by the wiper itself, the wiper is a rubber product, and it will be aged and hardened after a period of use, and it is more obvious in winter, if it has not achieved the cleaning effect, the simplest and most effective solution is to directly replace the new wiper blade. Generally, wiper blades are recommended to be replaced for a year or a year.

2. The foreign object between the wiper blade and the windshield produces abnormal sound, when the wiper is started, there will be a sharp friction noise between the wiper blade and the windshield of the front buttoner, and the owner can check the cleaning of the foreign object under the wiper to ensure the cleaning effect of the wiper blade.

3. The sound of friction of the wiper rod bushing, the wiper connecting rod of the long age will age, the elasticity of the wiper arm spring will decrease, and the bushing will wear out or even fall off. Please check the wiper arm or wiper linkage bushing.

Photo by Liang Kexin of Pacific Automobile Network).