Kyocera KM5035 how to share printers with network cables

Here's how to do it: 1. Set up printer sharing.

On the computer where the printer is installed, click Start - Printers & Fax, and the successfully connected printer will be displayed. Then find the printer icon, right-click, click the "Properties" option, enter the following setting interface, click the "Share" option, set it as follows, and click "OK" when finished.

2. Find the IP address of the computer where the printer is installed.

First of all, find the IP address of the computer where the printer is installed, click Start-Run, enter cmd and press Enter, the DOS window will pop up, and enter IPCONFIG in it to view the IP address of the machine. For example:

3. Connect to a shared printer.

4. At this time, find the shared printer, which should correspond here"hp laserjet", double-click the printer icon, and the following dialog box will pop up"You"Whether to install the printer driver, click Yes, and then click Next, and then it will be prompted"You"Whether to set this printer as the default printer. At this point, the printer shared in the network has been installed.

5035 is Mao to use network sharing.

Just install the network driver directly.

Sharing, it's a waste of network printing.

Nanjing Acstar photocopier rental company.

Kyocera experts.

Click on the second silver-white button on the left side of the machine, Printer

Interface - Network Settings - Set IP address is fine.

Nanjing Acex photocopier rental company Kyocera expert.

I'm a salesperson at Kyocera Electronics. Is the 5035 you are asking about a board-to-board connector? Generally, the part number is longer. Example 14 5804 010 000 829+

KM4031 may be the material of crystal oscillator. You ask ip, I don't know what you mean?

If you have any other questions, please email: ,

What IP. On a print card or on a computer?

Kyocera KM-2050 2550 3035 4035 5035 Scan Card Setup Instructions.

Scan to PC Setup Steps.

1 (1) First, install the Kyocera Scan Component on your device.

2) Set the IP address in Initial Settings, Scan Initial Settings, and Basic System Settings. Note that DHCP should be selected Off.

2 Set the sender and recipient.

1) Open the Internet Explorer browser on your computer, enter the IP address in the address bar, and open the Internet Explorer interface.

2) Select "Basic System Settings" to see if the settings are correct.

3) Select "Sender List" to set the sender.

The sender is the sender, and you can set up to 40 senders.

4) For example: Select 001

Enter the "Login name" and then "IP address of the PC with the address book".

Then submit. 5) Determine the recipient, i.e. the "destination list" that scans to the PC

6) For example, select 001

Enter the IP address of the Login Name and Destination PC (the IP address of the destination PC is the IP address of the recipient user's computer).

Note: The "Customer Document Number" should match the "Login Number".

Then submit. You can set up to 100 destinations in the destination list.

7) After the scanning part of the copier is set, start setting the computer part.

First, install the scan file utility software, which is available on Kyocera's drive CD.

This software acts as a file transfer bridge between the photocopier and the PC, putting the documents scanned from the photocopier into a designated folder. During the installation process, we will be asked to select "Service Mode" or "Desktop Mode", usually we select "Service Mode" so that the boot will start automatically. Once installed, the pointing icon will appear on the bottom right foot of the computer.

8) Create a folder for storing the scanned files. (Scanned files are automatically entered into this folder).

9) Set up the scanning software.

Right-click on the scan software icon, the following figure appears, and click Settings.

10) The following dialog box appears, click Settings.

11) The following appears, click "Open File", this step is in setting the archive path of the scanned file.

12) If the following appears, fill in the form.

Note: The number must be the same as the number in the "destination list" of the login area, for example, 001, and 001 should be entered here

Click where you point to set the file path.

13) The following appears, set the file path, e.g. find the folder set by scan in step (8).

14) After the file path is set, OK.

Select "Receive Notification" and "Allow File Rewriting". Are you sure.

15) Then OK.

16) Right-click on the scan software icon and select Start.

17) Set-up. NoteIf you have installed antivirus software for Windows XP, be sure to turn off the firewall.

Select the recipient Append Recipient and Address Confirm Start.

Simple 1Set the IP address of the machine.

2.Computer follow the scanning software.

3.Browser to go to machine settings.

4.Just leave when you're done.

Nanjing Acstar photocopier rental company.

Kyocera experts.

The processing speed is slow due to the large size of the document that should be too large.

Network printing speed depends on the processing speed of the network, computer, and printer. First, look at the speed of the computer processing the printed document; Looking at the network transmission speed, the printing information from the computer to the router of the LAN to the network card of the printer, if there are more network users, it will naturally be slower. Although the printer computer is in the same office, the printing information has to go around the router in the computer room.

Finally, there's the printer's native speed.

Network printing is meant to be sent to the copier's memory for processing, and it must be slow.

In the Print Properties dialog box, find the checkbox and check it.

There are two functions that are simply used, one is the size of the original.

The other one is a two-in-one.

The size of the original should be A5.

The 2-in-1 can be opened.

Then scan it twice and press Confirm to get the paper out.

Kyocera 5035 supports this feature, 4030 does not.

Nanjing Acstar photocopier rental company.

Kyocera experts.

Select the 2-in-1 original size, select the A5 ID card on the release table, and press the Start key.

After scanning the surface, turn the ID card over, sweep the other side, press the start button as well, and finally press the scanning finish (in the lower right corner of the LCD screen) to finish.

Original size selection A5 - 2-in-1 - 100% scaling - scan 2 sides - OK

How many of these machines do you have?

First of all, see if you have a scan card, and the print card is not the same as the one above that is clear, do you use the scanned IP into the IE settings? ,

Almost useless. Or rather, it is not useful for ordinary users.

For caching data, you can also install third-party programs to achieve certain functions.

The Kyocera 5035 printer charging stand is not fixed with screws, and you can pull it out by pushing the charging rack to the right.