What should I do if the water dispenser is not heated?

Here's a copy of the information! I found it when there was a problem with the company's water dispenser before! Share it now!

1. The whole machine has no electricity (no heating, no refrigeration): check whether the power socket has electricity, if not, turn it on.

Check if the power plug is in reliable contact with the outlet? If loose, plug it in firmly.

Check whether the internal and external power cables of the machine are disconnected? Does it fall off with the plugin? If there is, it is connected.

2. If the light is not lit and the heat is not made, how to reset the reset thermostat?

The 96% manual reset thermostat is used as the overheat protector of the hot tank in the water dispenser, and the thermostat fails, and when the temperature rise of the hot tank is too high or the water is dry, the manual reset will act, cut off the power supply, and play a protective role. The thermostat does not automatically reset after jumping, and must be reset manually. The reset method is:

1) Unplug the power plug and cut off the power supply; (2) Wait for the water temperature of the hot tank to drop below 25%, and press the reset button of the thermostat.

3. Leakage: Check whether the power cord is damaged, cracked, or exposed metal wire, and repair or replace it if so.

Check if the electrical outlet is securely grounded? Otherwise, do a good job of grounding, mainly because the water dispenser is poorly grounded.

Elimination method: It is necessary to use a reliable grounded three-pin socket and install a leakage protector, and eliminate the leakage fault in time. Ask a specialist or use a megohmmeter to check the ground resistance.

4. Is the hot water not hot, and the cold water is not cold?

It may be: too much hot and cold water in a short period of time; The power is not connected; Cold water refrigeration water refrigeration time is not enough.

Exclusion method: Wait for a while, you can take water again, pay attention to the appropriate water consumption of the water dispenser;

Check whether the heating switch is placed in the "on" position, whether the power plug is plugged in, and whether the power socket is electrified; Refrigerate for the first time and use water again two hours later.

5. No water: (1) The faucet does not come out of water.

Reason: large bottle without water; The inlet of the water inlet smart column is blocked by the large bottle cap sealing paper.

Exclusion method: replace with a new bottle of water; Remove the waste paper, take care to remove the sealing paper from the bottle cap, and then fill the large bottle of water.

2) The cold water tap does not come out of the water.

Reason: Ice blockage.

Exclusion method: Turn off the refrigeration switch for four hours.

6. What is the reason for the excessive noise of electric heating pipes?

It may be: slight fouling of the electric heating pipe after long-term use.

Exclusion method: Clean the hot tank with 2% edible citric acid solution, the method is the same as that of water dispenser detoxification.

7. Water leakage: (1) It may be because the bottle is damaged, check the method: cover the bottle with a dry towel, there will be water seeping into the dry towel in the damaged place, solution: replace the bottle.

2) There are many bucket diameters on the market and cannot be unified, and the connection between the bucket and the smart and bright part will be poorly matched, resulting in leakage.

3) The early design of the antibacterial design smart seat may cause water to overflow from the smart seat due to the failure of the check valve.

4) Mainly occurs in the connecting part of various machines.

Cause: There is a gap between the silicone parts and other parts or the connecting pipe is broken;

The connection of each silicone tube is loose, such as the nylon tie (used to tighten the pipe connector) is loose and causes water leakage; The screws between the hot tank cover and the hot tank barrel are not fixed tightly or loose, resulting in a gap and water leakage.

Solution: You can tie the fastening or replace the screws by yourself.

1. There are many reasons why the water dispenser is not heated, first check whether the indicator light of the water dispenser is on, if not, then the water dispenser is not heated is likely to be plugged in.

2. If the indicator light of the water dispenser is on, but it still can't be heated, then it may be caused by poor contact with the socket, as long as you replace a socket.

3. What happens if the water dispenser is heated all the time? If the water dispenser has been heating, it is possible that the heating pipe of the water dispenser is broken, and the heating pipe of the water dispenser needs to be replaced at this time.

1. The power indicator of the water dispenser is not lit, and it is neither heated nor refrigerated. If the indicator light is not lit, it is generally because the power socket is out of power, or the socket is not in good contact, followed by the internal switch and circuit inspection of the water dispenser. Usually, if the internal parts of the water dispenser are not energized, you need to disassemble the water dispenser, take out the back cover to check, and see if the line interface is tightly linked, otherwise it needs to be plugged and unplugged again, otherwise the poor contact may directly burn out the water dispenser.

2. All the indicators of the water dispenser are fully lit, but they are not heated. This should be uncommon for newly purchased water dispensers, and it may be caused by the direct falling off of the internal unreliable lines during transportation and transfer. If this problem occurs after a period of use, it is necessary to check whether the fuse is damaged.

This is also likely to be caused by the disconnection of internal wires. For energized but not heated, it is usually necessary to use a professional electrician's tool for measurement, and direct physical touch is strictly prohibited.

3. The temperature control parts are damaged or enter the safety protection state. Most of the products on the market are equipped with professional intelligent adjustable temperature control devices, and usually some manual solutions are also set up for burial. If there is a problem with the thermostat and the temperature does not heat, you only need to follow the instructions to restore the corresponding action.

If it does not work after the above work, the old control equipment of Wenwanchen will be damaged, and you can only find a merchant to replace it.

4. The temperature control switch jumps open, or the thermostat is damaged. Open the lid on the back of the water dispenser and you should be able to see the canister used to heat the water. Generally, there are two round things directly facing you, with two strands of wire, that is, the thermostat, generally the lower one is used for repairable temperature control, characterized by a small button, you use a chopstick to top the button to see if the water dispenser is good, if it is still the same, brother Sui, it must be the temperature control is broken.

Only replaced. The two wires on the thermostat can be shorted to test the quality of the test, if the short-circuit is powered on, it can further prove that the temperature control is damaged, and it can be replaced. Take care to check if the fuse is damaged, it is a black unscrewable thing inside.

Many people especially like to drink hot water and find it more comfortable. The water dispenser has a heating function, but I suddenly found that the water dispenser was not heating, and I felt very troublesome. Let's take a look at the reasons why the water dispenser doesn't heat up!

The small faults of the water dispenser are really annoying, and only by finding the right cause can we better solve the problem. There are also many situations in which the water dispenser does not heat, and the reasons for this vary in nature.

1.The water dispenser indicator light does not light up and does not heat up. Possible cause: The power supply is not connected; The fuse is burned out; The circuit board is broken.

2.The water dispenser indicator light is on but not heated. Possible causes: burned-out heating tubes; Bad thermostat.

1.Disassemble and see that there is a black component on the wall of the heating kettle, that is, the thermal switch, test the resistance value at both ends of the bottom with a multimeter, the resistance value indicates that the heating element is good, if there is no resistance value, the kettle needs to be replaced.

2.If it is judged that the thermal element is bad, you need to replace the thermal element, you can buy it in the electronic city, if you can't buy it, there is a way to solve the heating, that is, the two ends of the thermal electronics are directly in contact, but this will lead to continuous heating after turning on the heating switch, if you can master the switch every time the water boils, you can solve it in this way.

1.Turn on the refrigeration switch The refrigeration indicator does not light up for the following two reasons: the circuit board is broken, and the power supply of the refrigeration circuit is abnormal after the circuit board is damaged, so the indicator light will not light up; The fuse is burned, the fuse is not burned out, the general fuse is burned out due to other reasons, such as the circuit board when there is a short circuit in the fuse tube is usually burned, that is to say, when the fuse is burned out, it can not be simply changed to the fuse to be powered, the real cause must be checked out and eliminated before the fuse is replaced and tested.

2.Turn on the refrigeration switch and the refrigeration indicator light is on, there are the following two reasons: the electronic refrigeration sheet is broken, the electronic refrigeration sheet is the core component of refrigeration, if it is damaged, the water dispenser will not be able to refrigerate; The fan is broken, after the fan is broken, because the temperature of the heat sink can not be dissipated in time, so the water from the cool faucet is hot or high at the same room temperature water temperature, in this case, the refrigeration switch should be turned off in time, the fan does not work normally, and the power on will easily lead to the damage of the refrigeration sheet.

1. If the indicator light of the water dispenser is not lit and not heated, the cause of the failure may occur: the power supply is not connected; The fuse is burned out; The circuit board burns out.

2. Treatment method: Check whether the heating is placed in the "open" position. power supply and whether there is electricity at the outlet; replacement of the fuse; Replace the circuit board.

3. If the indicator light of the water dispenser is on but not heated, the cause of the failure of the impulse may be: the heating tube is burned out; Bad thermostat.

4. Treatment method: replace the heating tube; Replace the thermostat with a fiber judge.