-
Disassembly:
Unplug the power first, turn on the two switches of the water dispenser, and drain the remaining water in the bucket.
2.Open the drain pipe behind the water dispenser, drain the remaining water, and then screw the valve nut on the drain pipe. Generally speaking, the remaining water in the sewage pipe is usually the key to secondary pollution of the water dispenser.
3.Dissolve 1 decontamination effervescent tablet specially used for disinfection of water dispensers in about 2 liters of water to make a disinfectant, and then use it to scrub the inside and outside of the inner tank and lid of the water dispenser.
4.Pour the remaining disinfectant into the water dispenser, leave it for 10 to 15 minutes, and then turn on the switch of the water dispenser, including the sewage pipe and drinking water switch, and drain the disinfectant.
5.Rinse the entire cavity of the water dispenser continuously with 7 8 liters of clean water, and then turn on all the switches to drain the rinse liquid.
Cleaning Method:
1.Use citric acid to remove limescale from the water dispenser.
The water dispenser is used for a long time, and the mineral water or purified water will form scale, and the scale will reduce the efficiency of the water dispenser when it is heated and make noise.
Like conventional drinking water, buckle the prepared disinfectant bucket on the water dispenser and place it for 4 hours, open the water valve, release the scale and dust liquid, and then fill and flush four or five buckets of clean water to the water meter, and fasten the drain valve cap.
2.Add lemon to remove limescale from the water dispenser.
The water dispenser has been used for a long time, there is a layer of white slag in it, take a fresh lemon, cut it in half, remove the seeds, put it into the water dispenser and cook for two or three hours, you will find that the slag inside has become less, try a few more times, there will be a satisfactory effect!
3.White vinegar removes limescale from the water dispenser.
1. Unplug the water dispenser, open the sewage outlet behind the water dispenser, and clean the water inside (including the water storage tank and the water storage in the inner tank). Then take off the plastic seat cushion on it (the plastic seat cushion is the part that comes into contact with the mineral water bucket), pour white vinegar into the water dispenser, and bag a bag of white vinegar, and look at the bottle. After pouring in, open the faucet to put an appropriate amount of water to ensure that the white vinegar enters the water storage tank.
2. Put the plastic seat cushion back on, plug it in, heat it for 30 minutes, put the white vinegar out from the faucet and the sewage outlet respectively, and then put water into it, this step is best repeated three or four times.
3. This cleaning method is best carried out regularly, using the acidity of white vinegar to dissolve the scale, so as to avoid the accumulation of scale.
-
Water dispenser cleaning method 1: white vinegar.
Turn off the power of the water dispenser first, remove the bottled water (ensure that there is water in the water dispenser tank), remove the socket, pour the white vinegar into the water tank, turn on the power to heat, use the water cup to connect the water at the water inlet, and then pour it into the water tank, repeat many times. Finally, open the drain of the water dispenser and drain the water from the tank. Rinse with water repeatedly.
Water dispenser cleaning method 2: water dispenser disinfectant.
Turn off the water dispenser and remove the bottled water. Pour a small amount of disinfectant into the smart seat, pour some water, make the disinfectant water cover the plastic rod in the middle of the smart seat, soak for about five minutes, and then use a toothbrush to clean the surroundings of the smart seat. After cleaning, open the drain of the water dispenser and drain the disinfectant water.
Then add clean water and rinse several times.
Why do drinking fountains get dirty?
People are also paying more and more attention to the cleaning of water dispensers, so how does the water dispenser get dirty?
First, the material of the water dispenser itself: the working principle of the water dispenser is to use the air pressure to design the circulation system, and secondly, the water dispenser uses plastic and other chemical materials. Therefore, pollutants in the air and plastic materials will be polluted after long-term use, which is also an important cause of pollution in water dispensers.
2. Pollution caused by the use process: water dispensers use more bottled water, and the outside air will enter the water tank when changing the water, and some pollutants and bacteria contained in the air will also enter the water tank, which will breed a large number of bacteria and endanger human health for a long time.
3. Structural defects of water dispensers: Many people think that there is no water in the bottled water, and there is no water in the water dispenser, but in fact, even if there is no water in the bottled water, there is still about 1000 ml of water in the water tank. Every time the water is changed, the water will come into contact with the air, and over time, there will be more and more bacteria in the water, and even the production of other bacteria.
In life, there are many unexpected health threats to people, and the water dispenser should be cleaned regularly to avoid secondary pollution of drinking water and ensure the safety of drinking water.
-
Cleaning frequency: If the inner tank of the traditional water dispenser is not cleaned for more than 3 months, a large number of bacteria, residues and even bloodworms will breed, which will attach to the inner wall of the hot tank and become toxic"Additives"。
It is recommended that the water dispenser should be thoroughly cleaned at least once every 2 months. In summer, the temperature is high, and bacteria are easy to breed, so you should wash it every month, and you can do it yourself at home, and there is more than one way.
1. Wash with homemade lemonade.
2. Wash with white vinegar.
3. Wash with baking soda.
Detailed steps: 1. Power off. Be sure to unplug the socket before cleaning, and do not operate it with electricity.
2. Drain the water in the water dispenser, turn on the hot and cold water switch, open the sewage outlet (usually a knob made of white plastic) behind it, and turn off all the drains after all the water is cleaned.
3. Remove the "smart seat" (that is, the part of the water dispenser that touches the mineral water bucket), carefully scrub the inner tank and the inside and outside of the lid of the water dispenser with alcohol cotton wool to prepare for the next step of disinfection.
4. After pouring in white vinegar or lemonade or baking soda, try to fill the inner tank of the water dispenser with the solution, and be sure to fill it, otherwise it will be easy to burn out the inner tank when it is heated.
How do you see if it is full of inner tank? When the solution of the base does not seep down, open the hot and cold water outlets, and the solution flows out from both outlets, which means that the inner tank is full.
5. Put the smart seat of the water dispenser back on, then turn on the power and let the water dispenser heat up for 40 minutes. Then disconnect the power supply, turn on the hot and cold switches, as well as the drain on the back, and let the solution out.
After the cleaning solution is drained, pour in the water two or three times until there is no smell, so that the inside of the water dispenser will be cleaned!
-
In order to drink water conveniently, many families will install a water dispenser at home, and after the water dispenser has been used for a long time, a lot of scale will generally accumulate inside, so it needs to be cleaned regularly, so how to clean the water dispenser? Let's learn with me.
How to clean the water dispenser
1. If you want to clean the water dispenser, you first need to unplug the power plug, and then use a clean rag dipped in some dish soap to wipe the entire shell, sink, and locker of the water dispenser.
2. Secondly, all the water inside the water dispenser should be cleaned, and then the smart seat on the water dispenser should be removed, and then the pure water should be poured into the water storage tank, and then the water storage tank should be cleaned. Then turn on the tap of the water dispenser and let the dirty water in the water storage tank be drained.
3. Next, you should pour a bottle of beer into the water storage tank of the water dispenser, wait for more than an hour, and then turn on the faucet of the water dispenser to let the beer in the water storage tank be drained clean. Then use a clean rag to wipe the water storage tank carefully, and then use clean water to clean the water storage tank about 3 times.
4. Then pour an appropriate amount of white vinegar into the water storage tank of the water dispenser, then plug the power plug of the water dispenser into the socket, then turn on the power switch of the water dispenser, let the water dispenser heat up for about 40 minutes, and then turn on the faucet of the water dispenser, let the white vinegar in the water storage tank be discharged, and then use clean water to clean the water storage tank about 2 times.
5. Finally, pour an appropriate amount of special cleaning and disinfectant into the water storage tank of the water dispenser, wait for about ten minutes, and then turn on the green faucet and red faucet of the water dispenser, so that the disinfectant in the water storage tank is discharged, and then use clean water to clean the water storage tank several times.
6. After the inside of the water dispenser is cleaned, use cotton dipped in some alcohol to wipe the faucet and surrounding positions of the water dispenser clean.
7. After the water dispenser is cleaned, there is generally still disinfectant left inside the water dispenser, so the water inside the water dispenser is generally not allowed to be used immediately, and the water flowing out can only be drunk when it does not have the smell of disinfectant.
The above is a detailed introduction to how to clean the water dispenser, I hope it can help you solve the problem of cleaning the water dispenser. It is recommended that you must clean the water dispenser according to the correct cleaning steps to ensure that you and your family can drink safe and safe water.
-
The cleaning methods of the water dispenser include white vinegar cleaning and disinfectant cleaning.
1. White vinegar cleaning.
Disconnect the water dispenser from the water dispenser and drain the remaining water in the water dispenser. Remove the plastic seat cushion from the water dispenser that is stuck in the canister. Pour about 250ml of white vinegar into the water dispenser, then turn on the faucet to verify that the white vinegar has entered the water storage tank.
Put the plastic seat cushion back in, then plug it in and heat it for about 40 minutes.
Put the white vinegar out of the faucet and the water outlet behind the water dispenser, then add the water to the water dispenser, and repeat the above steps two to three times. Wash the remaining vinegar from the water dispenser.
2. Disinfectant cleaning.
Choose water dispenser disinfectant and choose food-grade disinfectant, and the active ingredients of common water dispenser disinfectant are represented by chlorine dioxide and hydrogen peroxide. Among them, chlorine dioxide has a low cost, but the residue is not easy to clean; The residue of hydrogen peroxide is easy to clean, but **high. When using chlorine dioxide for disinfection, soak it in a solution with a concentration of 50-100mg l for 5 minutes to achieve the purpose of disinfection.
When disinfecting with hydrogen peroxide, the soaking time is the same as 5 minutes, but the concentration is. Disinfection in this way is one of the most thorough methods.
Water dispenser maintenance method:
1. Keep the water dispenser upright when handling, such as tilting, the inclination should not exceed 45 degrees, and avoid touching the hardness during the handling process, so that the outer surface is damaged.
2. When using the water dispenser for the first time, pay attention to leave it for a while, clean it with clean water, open the valve to drain the remaining water, and then add water to use. When the water dispenser is out of use for a long time, remember to unplug it and drain the remaining water to avoid the growth of a large number of bacteria in the body.
3. When the water dispenser is not used at night, do not turn it on, which will waste electricity, easily cause loss, and shorten the service life of the water dispenser.
-
Water dispenser cleaning method:Tools Ingredients: juicer, lemon, white vinegar.
Method Steps:1. Wash with homemade lemonade, first cut the lemon in half, and squeeze out the juice in the lemon with a juicer.
2. Mix with water, it is recommended to mix one lemon with 250 ml of water, then turn off the water dispenser, release all the water inside, and pour in homemade lemonade.
3. Turn on the power supply, turn off the power after boiling, pour out the cooled lemonade, and rinse it with water several times.
4. Clean with white vinegar, vinegar and lemonade are weakly acidic water, which has a good ablation effect on calcium carbonate in the water dispenser, mix white vinegar and water in a ratio of 1:1, pour it into the water dispenser, cool it after boiling and then pour it out, and then wash it with water several times.
-
Water dispenser cleaning method: First, disconnect the power of the water dispenser, remove the bucket above, and clean the remaining water in the water dispenser. Then open the plastic lid of the bucket and pour white vinegar or water mixed with citric acid into it.
Finally, plug in the water dispenser, heat for 40 minutes to about an hour, open the faucet or drain, drain the white vinegar or citric acid, and then pour in the water in the same way and heat it repeatedly, preferably three to four times.
Precautions for using water dispensers: Increase the frequency of use. Frequent use of the water dispenser is equivalent to frequent flushing with running water, which can reduce limescale deposition and bacterial growth. Families who usually use it less should wash it once every two weeks; If it is used frequently every day, it is guaranteed to be cleaned once a month.
Clean faucets and sinks in a timely manner. The faucet and sink of the water dispenser are often in contact with the air, if the milk, juice, coffee, etc. in the cup come into contact with the faucet when receiving water, it should be rinsed with clean water and wiped dry in time. There should be no foreign matter such as tea leaves in the sink, and if there is a stain, it should be removed and cleaned, or once a week.
Clean the bucket trough frequently. Sometimes the water in the bucket looks empty, but there is still stagnant water at the tank of the bucket, which can accelerate the growth of bacteria when it comes into contact with the air, so drain the water before changing the water each time. If there is white or yellow scale in the trough when changing the water, it should be cleaned in time.
Li Fuxing, a special expert of the Health Times and director of the Healthy Drinking Water Professional Committee of the China Medical Promotion Association, pointed out that the current water dispensers are basically bile water dispensers, which are heated by the hot gall in the machine, and the biggest problem of this water dispenser is that it will process "thousands of boiling water", the reason is that the water in the hot tank of the traditional water dispenser is always in the cycle of heating, cooling and reheating. If the "thousand boiling water" is stored for too long, the water will age, the activity of the water will be reduced, and it is not easy to be absorbed by human cells. Another health hazard of water dispensers is that the secondary pollution of water is more serious. >>>More
There was a problem with the temperature-controlled version of the water dispenser. >>>More
Electric kettle is better. If the water dispenser wants to drink boiling water at any time, it must turn on the switch, the working principle is to turn on the power switch, start heating, the water is boiled, the power supply is disconnected by the thermostat, the temperature drops to the set temperature such as 70 degrees, the thermostat is turned on and automatically starts heating, if there is no one to use the water for a long time, especially in winter, it will work again and again, it is a waste of electricity and a thousand pots of water are not good for the human body, the best practice is to turn off the water dispenser power when people leave. Hope it helps.
This one can't, for the following reasons:
1. The inlet pipe is drinking water, and the waste pipe discharges waste water (containing a large number of harmful substances), if it is placed in a water tank, it will pollute the water in the water tank. >>>More
Select the feature. 1.Depends on usage.
General high-pressure washers can be divided into two types: household and professional. If you use the washing machine for less than 50 hours a year, you only need to buy a household cleaning machine. The price is relatively cheaper, the weight is lighter, the material is simple and not heat-resistant. >>>More