-
Anonymous users2024-02-06How to connect the projector to the computer The projector is connected to the desktop computer.
1. Prepare the computer that needs to be connected to the projector and the required cables.
2. Take out the end of the connected graphics card and connect it to the monitor end of the projector.
3. The RGB cable connects the projector and the computer.
4. If there is an audio input cable connected to the audio in of the projector.
5. Connect the audio amplifier at one end of the audio out.
6. Connect the power cord of the projector.
How to see 3D when the projector is connected to the computer
1. The projector supports 3D projection, and prepares the 3D film source of the projector support format, such as MX661 can support up and down, left and right, frame sequence format 3D film source.
2. Connect the projector to the host computer via VGA or HDMI cable.
4. Press the menu key of the projector (menu) - display - 3D mode - select the corresponding mode (the left and right screens are selected side by side, the upper and lower screens are selected from top to bottom, and the frame sequence is selected in the frame sequence).
5. If the 3D mode is gray and cannot be selected, you need to change the output timing of the computer.
6. Open the projector manual, take MX661 as an example, if you need to ** left and right format film source, one star at the red box represents the timing of supporting left and right formats, so you can change the computer resolution to 800*600, change the refresh rate to 60Hz, and then switch to 3D mode, you can choose the corresponding 3D mode.
7. When the picture becomes ghosted. Wear 3D glasses to **3D effect. Note: BenQ DLP Active Shutter 3D glasses are required.
Precautions for connecting the projector to the computer.
Note that the VGA signal cable must be tightened, otherwise there may be a problem of color shift in the projected image, if the problem is not solved after tightening, you can try to replace the cable. In addition, if you need to use a remote control to operate the computer with a VGA signal cable, you must also connect a signal control cable.
Generally, users will set the 17-inch CRT monitor to 1024*768@85 or higher resolution and refresh rate, but when using a **splitter to connect the monitor and projector at the same time, you should pay attention to the resolution and refresh rate settings. When the projector prompts that the input signal is out of range, the resolution and refresh rate of the graphics card should be appropriately reduced, otherwise the projector will not be able to recognize the image.
-
Anonymous users2024-02-05How to connect a laptop to a projector.
-
Anonymous users2024-02-04Through the ** output interface of the laptop, we can easily output the image of the laptop to the projector, how is the specific setting method? What should we do to make the display output image clearer and more complete? Next, it's the problem I'm going to study with you, okay, let's take a look.
Method steps
2. Then, we can turn on the right button to open the screen resolution option, here we click "Connect to projector".
3. Then, we will open the relevant setting options. What we need to pay attention to is,We can use shortcut keys to operate,Press the Microsoft logo key and the P key,You can quickly turn on the relevant settings displayed by the projector。
4. If we choose "computer only", it means that the image will not be displayed on the projector, and the computer will not output the image to the projector; If we select "Projector Only", then the computer will turn off on its own monitor'Image output, which in some cases is beneficial for energy saving. As for copying, the resolution display output on the projector and computer is exactly the same; There is also an extension function, we can put the image output on one monitor to two monitors, and we can also adjust the resolution of these two different monitors differently, which needs to be adjusted by ourselves according to actual needs.
5. In general, we use a projector to show PPT or some ** manuscripts, specific settings, we can adjust different displays in the screen resolution, here you can refer to the setting process of your own monitor.
-
Anonymous users2024-02-03Here's how to connect your computer to the projector:1. Connect the laptop and projector to the same wireless network environment.
<>3. Turn on the music broadcast screen on the notebook and projector.
4. Open the system settings of the projector, and change the signal source to HDMI to complete the connection on the same screen.
-
Anonymous users2024-02-02Prepare a VGA cable, connect the projector and the computer respectively, set the projector signal source to "computer" after connection, and then click [Start Menu] - [All Programs] - [Accessories], find and click [Connect to Projector], select [Copy] in the pop-up window to connect to the computer, and see the projection effect.
Core i5 Lenovo Legion.
Win7 Ultimate 64-bit operating system.
The all-round king of projection.
1. Turn on the screen projection on the computer and TV. Make sure both devices are connected to the same network, as shown in the image below.
2、Next, you need to cast the screen on the computer side CampyKingClick on the computer above to cast TV,As shown in the figure below。
3. Click on the discovered device to cast the screen. Tap the discovered TV device and tap Cast screen.
4、At this time, a window will pop up on the TV side to confirm the projection, click Allow。 If you don't want this window to pop up next time, click Always allow.
5、Finally, you can find that the computer has successfully projected the screen to the TV,As shown in the figure below。
The **input of general equipment The output yellow is video,And white、Red is the left and right channels of audio,If you want to try the yellow connector to be able to match the connection with the projector,You can try it。 >>>More
To connect to the network on a desktop computer, you need to choose a broadband PPPOE connection method, fill in the broadband account and password, and then click to connect to the broadband. The desktop computer creates a network connection as follows: 1. Click the [Start] button on the computer, then click the [Control Panel] button2, pop up the [Control Panel] window, click [Network and Sharing Center] 3, pop up the [Network and Sharing Center] interface, click [Set New Connection or Network] on the right, as shown in the following figure4, pop up the [Set Connection or Network] window, click the first item [Connect to Internet]5, click [Next], and the [Connect to Internet] window pops upIf you have already connected to a network, then select the second [still set a new connection] button and click 6, select the [broadband PPPOE] connection method 7, pop up the interface of setting broadband account password, and then click the [Connect] button after filling in the broadband account and password to connect to broadband. >>>More
There's nothing surprising because your IP address is automatically obtained! Maybe the interface of your network cable is not standard, so it will fail to get it automatically, and you can usually set the IP address manually. For example, nothing else needs to be moved, and even if there is a yellow exclamation mark, it will not affect broadband dial-up Internet access!
Listen to you, you should use the dial number. You should use the cat directly on the net. No routing, only you are using your network cable? >>>More
Ways to create a broadband connection:
1. Open the network sharing center. The network sharing center is in the control panel, or you can open it directly on the desktop, click the network icon in the bottom right corner of the desktop - select Open Network Sharing Center. >>>More