The season and method of cuttings, the time and method of cuttings

The best time to do this is in the month of the year, or in the month of the year.

How it works: 1. Obtain cuttings: The flower branches that have finished flowering on the adult plant should be selected as cuttings, and it should be cut from the place where it is connected to other flower branches.

Be careful not to leave broken branches on the plant, as it is easy for rot to occur. After cutting, cut it short to 15cm long, remove the lower end of the leaf, and then soak it with Bika rooting agent for about 30min.

2. Cuttings: Prepare some thick flower soil, put it in a flower pot, and wet it with water. Then insert the cuttings gently into it and slightly gather the surrounding soil to make sure it doesn't fall over.

After that, place the pot in a semi-shaded position, maintain it for 15-30 hours, and replenish water in time when the soil is dry. This way it will soon be able to take root.

There are 3 kinds of cuttings, using live shoot cuttings, taking cuttings from April to May in spring or September to October in autumn, using hard branch cuttings, cutting in late winter and early spring, and using bud cuttings in spring. First, the live shoot cuttings method using the live shoot cuttings method for cuttings, the time is selected in the spring from April to May or autumn from September to October, the selection of good growth, no pests and diseases of the current year's robust branches as cuttings, cut the length of about 10 cm, the base and compound leaves each leave two, the rest of the leaves are all cut off, after the cut is smeared with carbendazim, placed in a ventilated place to dry until the cut shrinks, mixed with humus and river sand to make a substrate, the cuttings are smeared with rooting powder and inserted into the substrate 2 3, leaving 2 to 3 buds outside the substrate, Water once and wait for the new shoots to grow to indicate that the cuttings have taken root. Second, the hard branch cuttings method adopts the hard branch cuttings method for cuttings, the time is selected in late winter and early spring, the first half of the hard branch cuttings method is the same as the live shoot cuttings, the difference is that after watering permeability, it is necessary to prepare a tower to be placed on the container, covered with a layer of film, in order to keep warm and moisturize, after covering the film, place the cuttings in the position towards the sun, keep the substrate moist during the period, wait until the middle of spring, you can uncover the film, and wait until the cuttings turn green and grow the root system after you can transplant it to the pot.

3. The bud cuttings method is used for cuttings, the time is selected in the spring, when the new shoots of the moon flower grow vigorously, cut or break off the bud head full, disease-free and stout new shoots as cuttings, after smearing the wound with carbendazim, place it in a ventilated place to dry until the wound shrinks, prepare a loose and fertile substrate, scatter and poke a few holes with a small wooden stick, insert the cuttings into the holes 1 3, compact the surrounding substrate by hand, cover it with a layer of film, place it in a semi-shaded place, open the film for ventilation 2 times a day, keep the substrate moist, It takes about 15 days to take root, and about 20 days to uncover the film and transplant it into pots.

Cuttings can generally be carried out in seasons other than winter, and the survival rate of cuttings is the highest in spring and autumn.

It is suitable for planting in the spring by cutting a section to remove the roots diagonally and inserting it in the soil, because it is easy to feed.

The best time to take moon twin cuttings is summer and autumn. However, it is easy to take root and can be cut all year round.

When cuttings, be sure to cut the incision flat to reduce the wound area. The oblique incision is the practice of cutting flowers, whether it is before or after flowering, cuttings are arbitrary. Go to the top, do not cut off the leaves, and directly insert the roots into the water, which has a higher survival rate than cuttings in the soil, and the rooting is faster.

The time and method of monthly cuttings are as follows:

The best period for cuttings is after flowering, cutting off the branches under the buds, cutting the bottom of the branches into horseshoe shapes with a sterilized sharp blade, and keeping 2-3 leaves on the branches. The shoots were soaked in carbendazim solution for 3-5 minutes for disinfection, and the bottom of the cuttings was immersed in 600-800 times the rooting agent for 2 hours after removal. Use damp soil cuttings, and finally cover the film to moisturize and promote its rooting and survival.

Yueji is known as the queen of flowers, blooming in all seasons, flowers into large, rich aroma, can be widely used in horticultural cultivation and cut flowers, strong adaptability, cold-resistant, regardless of ground planting, potted plants can be, suitable for beautifying courtyards, arranging flower beds, with planting hedges, flower stands, decorating gardens.

Precautions for monthly and seasonal maintenance

1. It is necessary to prune the moon season regularly, and when the new shoots grow to 15 20cm, cut off the top about 3cm. The side branches grow to a certain length and need to be topped continuously. After flowering, cut off the residual flowers in time to promote the germination of new branches.

2. Fertilization must fully absorb fertilizer, and undecomposed farmhouse fertilizer cannot be used, otherwise it will burn the roots and leaves and bring harm to the growth of the month.

3. Pay attention to the good ventilation of the environment, otherwise it is easy to suffer from the interference of pests and diseases, such as aphids, powdery mildew and black spot.

If you want to turn 1 pot into multiple pots, Xiaoyou starts from the selection and cutting of cuttings, cutting medium and maintenance management after cuttings, and teaches you how to cut cuttings.

The time of the monthly flower cuttings is: April to May or September to October every year.

At this time, the branches are vigorous, vigorous and the temperature is suitable. Hard branch cuttings can be cut from the dormant period of the month to the germination of spring, but the temperature should be controlled when cuttings. The best season for bud cuttings is in the spring, when the sprouts are just germinating.

It is worth noting that the monthly cuttings should avoid the high temperature period in summer, because it is difficult to bud at this time, and the high temperature and humidity weather can easily lead to the growth of bacteria.

Cuttings method:

1. Hard branch cuttings:

Hard branch cuttings can be carried out before the fall of leaves in the month and season until the next spring before germination, basically the sturdy branches can be used as cuttings, watered thoroughly and covered with plastic film after cuttings, and the plastic film can be removed when the cuttings germinate in the spring of the second year.

2. Bud cuttings propagation:

Choose new shoots that grow stout, full of bud heads and the base of the main branch, wash them with water and then take cuttings, also cover them with plastic film, ventilate 1 2 times a day, keep the soil moist, take root after about half a month, and remove the plastic film after 20 days.

3. Shoot cuttings:

Shoots cuttings in April, May, September and October its growth season is the best, the temperature is the most easy to root and survive at 2 5 hours, the incision can be dipped in indole butyric acid powder, the cuttings are selected to be the robust flower branches of the year, and the roots can be taken after 30 days of cuttings.