How to eliminate FAW Volkswagen tire pressure lights

Hello, there is a row of buttons in front of the gear lever, the one on the far right (there is a pattern on the button and the pattern of the tire pressure warning light), the tire pressure of the two cars in front is the same, and the tire pressure of the two cars in the rear is the same, press and hold for 3 seconds, and when you hear a drop, the light will go out [There is a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

There are several ways to eliminate a faulty tire pressure light:

1. Re-set the fault lamp to eliminate it;

2. Press the set button with tire pressure identification on the rightmost right side of the front of the gear lever for a long time, if the tire pressure is normal, the alarm light can be eliminated;

3. You can press and hold the tire pressure monitoring button until the light goes out, so that it is eliminated and then press the tire pressure monitoring button until the light is on, so that it is set again;

4. It can be eliminated by setting it in the multi-function steering wheel. Or use a computer detector to reset and eliminate;

5. How to turn off the tire pressure indicator: open the glove compartment on the co-pilot's side, there is a button in the upper left corner (next to the sub-airbag key switch), in the case of turning on the ignition switch, press and hold the button until the tire pressure light goes out. However, the tire pressure must be within the normal range.

Elimination and initialization process of low tire pressure alarm:

1. Turn on the power of the instrument, press and hold the reset button until the tire pressure is low and the alarm light goes out;

2. Press and hold the reset button once until the tire pressure is low and the alarm light flashes three times;

3. In the normal driving process of the car, if a tire is flat and causes the tire pressure to be low, the speed of the wheel's straight driving will be higher than that of several other wheels (equivalent to the diameter of the wheel becoming smaller), after a certain distance, the speed sensor of the wheel is checked and the speed error of the other wheels reaches a certain value, then the tire pressure low alarm light will be triggered;

Volkswagen tire pressure monitoring light on elimination method: turn on the ignition switch, press the button of the tire inflation pressure control system set and hold, the tire monitoring button is located on the black button on the front panel of the gear lever, until the meter indicator lights up. After confirming that the new tire parameters are stored, the tire pressure light will be reset.

There are two ways to eliminate the tire pressure indicator of Volkswagen: 1. Go directly to the Volkswagen after-sales service store and ask the maintenance personnel to diagnose the fault code of the car computer and eliminate the error code; 2. Press and hold the tire pressure monitoring button on the right side in front of the gear lever, and the tire pressure light can be eliminated after three seconds. When the tire pressure light of the Volkswagen series is on, the first thing to check is whether it is really a tire that has a problem.

If there is no fault, it can be considered a false alarm, as long as the tire pressure light is eliminated. Volkswagen models are equipped with an indirect tire pressure monitoring system (TPR), which works by using the speed sensor on the car's ABS braking system to compare the number of turns of four tires.

Press and hold the tire pressure monitoring button on the right side in front of the gear lever, and the tire pressure light can be eliminated after three seconds. After the tire pressure light of the car series is on, the first thing to check is whether it is really a tire that has a problem.

Volkswagen's tire pressure indicator can be eliminated by using the tire pressure button on the right side of the gear lever and pressing and holding for 3 secondsThe specific steps are as follows:

1. Pull the door handle.

2. Open the door on this side of the cab.

3. Press the one-button start button.

Fourth, the instrument lights up, and the vehicle power is turned on.

5. Press and hold the button in the picture.

Precautions for operation:

1. Before pressing, inflate the tires.

2. The air pressure is best on the left and right.

Hello, Volkswagen series tire pressure fault light clearing, there are the following methods.

First, some models have a separate button, which can be cleared, this is generally in front of the gear lever in the car or there is a set button in the co-pilot glove box, after the vehicle instrument is powered on, press and hold this button for 3 to 5 seconds to clear.

Second, some models do not have this separate button, which is cleared at the position of the vehicle's central control display, directly press the CAR button, and then enter the vehicle system, select the tire pressure monitoring system, and then reset it.

Third, if the vehicle with the central control display is modified with a large-screen navigation all-in-one machine, then this cannot be removed manually, and you need to go to a 4S shop or repair shop to use a special computer to clear the tire pressure fault light.

Volkswagen SET light refers to: the vehicle's tire pressure monitoring indicator, if the SET vehicle tire pressure monitoring indicator light is lit, it means that the vehicle's four tires, at least one of which is lower than the standard pressure value, belongs to the state of gas loss. This requires checking the air pressure of all four tires with a tire pressure gauge, and inflating if there is a lack of air.

Press the SET button to reset after inflation is complete. This light will go off. Volkswagen has three main tire pressure reset modes, the first is in front of the gear lever or on the right side of the gear lever there is a button labeled set.

Just turn on the ignition switch, and after pressing this switch for three seconds, the tire pressure reset is complete. The second is to reset the tire pressure on the MIB II small screen entertainment system, first turn on the ignition switch, turn on the stereo, and press the SETUP button. Turn the knob on the right side of the radio to the tire gear.

Press the right knob once, remembering to press down instead of spinning. At this time, the screen will appear "whether to save tire pressure", if yes, press the right button once, and the tire pressure reset will be completed. The third is to reset the tire pressure on a large-screen entertainment system with MIB.

First turn on the ignition, turn on the stereo, press the CAR button, then click the settings button at the bottom of the screen, find the tire option, click on the tire, select SET tire pressure reset, click to save the data, and the tire pressure reset is completed.

There is a set button in front of the gear, and it can be eliminated by pressing and holding for 5 seconds to reset.

It is to reset the tire pressure on the MIB II small screen entertainment system, first turn on the ignition switch, turn on the stereo, and press the SETUP button. Turn the knob on the right side of the radio to the tire gear. Press the right knob once, remembering to press down instead of spinning.

At this time, the screen will appear "whether to save tire pressure", if yes, press the right button once, and the tire pressure reset will be completed.

Normal tire pressure. Tire pressure standards vary depending on the type of tyre and the type of tyre, and the required tyre pressure varies from vehicle to vehicle with different vehicle weights, heights, and tire sizes. The tire pressure is 240kPa-250kPa for standard tires and 280kPa-290kpa for enhanced tires.

Moreover, the tire pressure of cool tires is also different from that of hot tires, and the pressure of hot tires is about 20kpa higher than that of cold tires. The manufacturer's recommended value is the tire pressure value of cold tires, and the tire pressure in the cold car state is about 230kpa-250kpa, but the specific tire pressure marked on each car shall prevail.

In addition, the tire pressure is particularly affected by seasonal factors, the temperature is high in summer, the tire is easy to heat up during driving, and the tire pressure is easy to cause a puncture if the tire pressure is high, and the tire pressure is slightly lower; The tire pressure in winter is a little higher than that in summer, because the cold shrinkage and heat rise, so the tire pressure of the car in winter is generally between 250kpa-280kpa.

The car tire pressure warning light sign is a jar-like shape with an exclamation mark inside. Most models are equipped with a tire pressure monitoring system to monitor whether the tire pressure of the vehicle is normal at all times. When there is a problem with the tyre pressure of the vehicle, the tyre pressure warning light will be illuminated.

If the tire pressure warning light is on, it is best to stop and check what is causing the tire pressure problem. Identify the cause and repair it in time to avoid hidden dangers of accidents. It is important to know that if there is a problem with the tire pressure, the safety hazards that come with it can be big or small.

It is recommended that riders whose vehicles are not equipped with a tire pressure monitoring system should buy a tire pressure test tool to check the tire pressure from time to time to see if there is any abnormality.

The method of canceling the tire pressure light is different for each car, you can turn on the start ignition switch, press the tire pressure monitoring reset button, store the normal tire pressure data at this time, and then press the automatic clear original data, and it will be canceled.

3. Then press the "set" button in the next tire setting interface.

4. Then click OK in the window that appears on the Buick Excelle display.

5. Finally, after the Buick Kaiyue "tire pressure monitoring initialization" is completed, the tire pressure light is eliminated, is this clear? Kiss.

See if it is caused by the high air pressure of the tire, if there is more, you can put a little, and if you have less, you can add a little to meet the standard required by a car.

Toyota Crown.

There is a small set button above the brake pedal that resets when pressed once.

Buick GL8 old GL8 is not a tire pressure monitoring system! **GL8 Lu Zun, the elimination method is in the middle of the air conditioning outlet, there is a Enter button next to the (right) press a few times, see that the instrument will display the tire pressure reset, and then press and hold the enter key.

Mercedes CLS300

1. The vehicle is in the starting state;

2. See if the instrument display is an image of the total kilometers (if not, press the return button on the lower left side of the steering wheel to display the total kilometers);

3. Press an upward arrow on the left side of the steering wheel (the instrument appears in English);

4. Press the R button on the instrument (if not, press a raised pole on the instrument and press it) (the instrument has a paragraph of English);

5. Press the + sign on the right side of the steering wheel;

6. Restart the vehicle OK and the air pressure light will not be displayed.

How do I cancel a car tire pressure failure light?

The front door on the right side opens, there is a gear plate on the side of the console, pull it open, there is a red button in it, turn on the engine and hold the button, the alarm is first flashed.

Each car series has a different approach.

Some cars, as long as the air pressure of the four tires is adjusted, will automatically extinguish after driving for a while, and some cars can only be eliminated by computer.

1.If the tire pressure monitoring system warning light is on during driving, stay calm, don't panic, immediately reduce your speed and avoid hitting the steering wheel and braking hard, and check your tires immediately.

2.Tire pressure monitoring is divided into indirect and direct tire pressure monitoring, and determining the tire pressure monitoring category of the car is conducive to solving the problem of tire pressure monitoring lights in time.

3.The direct tire pressure monitoring device is to use the pressure sensor installed in each tire to directly measure the air pressure of the tire, and use the wireless transmitter to send the pressure information from the inside of the tire to the ** receiver module, and then display the tire pressure data. When the tire pressure is too low or flat, the system will automatically alarm.

4.Indirect TPM works by saying that when the air pressure of one tire decreases, the weight of the vehicle causes the wheel to roll in a smaller radius, causing it to spin faster than other wheels.

By comparing the speed difference between tires, the purpose of monitoring tire pressure is achieved. The indirect tire alarm system actually relies on calculating the rolling radius of the tire to monitor the air pressure.

In this case, the regular operation of the owner is: first find a safe place to pull over, if the naked eye can not observe the obvious tire air and other imbalance, then after ignition, press the tire pressure button to reset. Continue to drive for a while, if the monitoring light is on again, inflate and balance the vehicle's four tires to the standard value, and then press and hold to reset.

Tire pressure is the pressure of the air inside the tire, too high and too low will shorten the life of the tire. Sometimes the tire pressure test light is on, and it is possible that the tire has been punctured by a hard object such as nails, resulting in a slow tire leak and an unbalanced tire pressure, which can generally be observed by the naked eye. In this case, there is no need to panic, as long as you don't pull out the hard objects that have been punctured, the tires will only slowly bleloaf, and you can completely drive the car to a 4S shop or repair place.

If the tire is badly damaged, you need to replace the spare tire and drive it to a repair shop for inspection.