How to remove the tip of the waste brush, and what to do if the brush is broken

I can't blame netizens for this incident, there are too many people asking questions, and they can't be busy.

If the brush is cut out, there are several ways to try to fix it:

1.If the tip of the brush is cut off, you can leave a part of the root of the brush, and then gently comb the bristles neatly and use scissors to cut the nib neatly.

2.If the barrel of the brush is cut, you can use a slender wooden strip or bamboo tube to connect the broken joint, and then fix it to restore the original shape of the brush.

3.If the bristles of the brush are cut, you can try to trim the root of the brush with scissors, then comb the bristles neatly, and fix the brush with glue or thin thread to restore the original shape of the brush.

If none of the above methods can restore the brush to its original shape, you can try using the egg method. Here are the steps to repair a brush using the egg method:

1.Crack the eggs and remove the whites for later use.

2.Put the washed brush in the egg white and dip it repeatedly.

3.Repeatedly run the bristles from the root down to the tip of the pen by hand, and then hang it upside down in a cool place to let it dry naturally.

4.Soak in warm water when using.

It should be noted that when using the egg method to repair the brush, it is necessary to keep the temperature of the egg white not too high to avoid damaging the bristles. At the same time, if you use glue to fix the brush with water or a thin wire, you need to be careful not to fix it too tightly to avoid damaging the bristles.

Step 1: It is recommended to wash the brush thoroughly with Minlv shampoo, then scald it with boiling water, and straighten the hair on the tip of the pen with your hands.

Step 2: Break the eggs, put the egg whites in a container, put the freshly washed brush into the egg whites, and dip them repeatedly.

Step 3: It is very important to repeatedly brush the bristles from the root of the bush to the tip of the pen with your hands, and then hang it upside down in a cool place to dry naturally. The next time you use it, soak it in warm water, just like a new pen.

Summary. How to prevent scattering: [Before the brush is inked, when using the brush, before dipping the ink, dip the pen in water to wet the pen, squeeze out the water and then enter the ink, so that it is easy to clean the root of the pen and not easy to produce ink accumulation.

Wash the brush when you run out] Clean the brush when you run out, and don't press the hard brush directly on the inkstone, which is easy to cause damage to the brush. Do not press violently when moving the brush, and do not press it for a long time, so that it is easy to split the brush bristles, damage the brush, and affect the use of shouming

What should I do if I separate the tip from the barrel when I wash the brush?

Prevention of scattering method: [Before the brush into the ink, when using the brush to cultivate the base, before dipping the ink, dip the pen in water to wet the pen, squeeze out the water and then enter the ink, so that it is easy to clean the root of the pen and not easy to produce ink accumulation. 【Brush is used up that is, wash the stuffy】Clean the brush after use, do not press the hard brush directly on the inkstone, which is easy to cause damage to the brush and the ant.

Do not press violently when moving the brush, and do not press it for a long time, so that it is easy to split the brush bristles, damage the brush, and affect the use of shouming

When washing the brush, the tip of the pen and the barrel of the pen are separated, and the treatment method is to use AB to teach to glue together.

When washing the brush and losing skin, the pen head and the pen barrel are separated, and the processing method is as follows: <>

You need to prepare two things, a set of AB glue and a platform for glue adjustment. Squeeze out the AB glue and do not mix it first. Use the broken pen barrel to stir the AB glue directly, so that the two glues are mixed together, and apply it directly to the pen barrel after stirring.

At this time, a large amount of glue has been stained on the barrel. The glue can not be put too much, and only the pin limb is applied on one side.