What should I do if I can t use the monitoring of the router connected with a network cable after ch

You need to set the dial-up type and enter the password for surfing the Internet.

1.Connect the network cable to the WAN port.

2.The other network cable is connected to the LAN port at one end and the computer at the other end.

3.Open a browser and enter the administrative address of the router, such as:

4.After logging in, you can go through the Setup Wizard to configure the basic information as required.

5.After the following settings are completed, you can surf the Internet normally.

6.Find Network Parameters --WAN Port Settings.

7.In the first item on the right, select PPPoe in the "WAN port connection type", enter "Internet access" and "Internet password", and click Save.

8.Once you restart your router, you're good to go.

It should be possible, you can set it as follows, use this network cable to connect your wireless router WAN interface, and then find the root network cable to connect your computer to the digital interface of the wireless router, log in to the router through the computer to set the WAN interface to the dynamic IP mode, and then select LAN parameter settings, and modify the LAN interface IP address for the general solution.

The gateway is not aligned. You can set up the new router in the same way as the monitored gateway.

See if your current router management address is, if not, it can't be used.

Enter the router management interface and change the LAN port address to Save after restart.

Set the DHCP address pool for normal routing and check whether the address pool is set to normal.

If not, change to.

See if the packets are filtered and open the corresponding port to try.

You should reconnect the route once.

Summary. Reset the monitoring directly, after the reset, according to the original networking mode, reconnect the router's wifi. Most of the monitoring is comrade later, and then directly in the search for the monitored device, and then directly on the mobile phone to connect the device to the wireless network.

Reset the monitoring directly,After the reset,According to the original networking method,Reconnect the router's wifi。 Most of the monitoring is comrade later, and then directly in the search for the monitoring equipment, and then directly on the mobile phone to the high to the excitant device connected to the wireless network.

1. The IP camera is powered on and connected to your router or switch with a network cable; 2. Under the same LAN, use the computer to open the camera branch search tool that comes with the camera, search for the IP of the camera, and change the IP to the same network segment as your computer; 3. Enter the IP of the camera you found or changed with the camera search tool in the IE address bar to log in to the camera in the LAN, enter the camera settings page, and set the relevant network options. 4. Log in to your route, check whether your routing settings have the blacklist and whitelist settings turned on, and you must allow the camera to access the Internet here;

Summary. 1. The IP camera is powered on and connected to your router or switch with a network cable; 2. Under the same LAN, use the computer to open the camera search tool that comes with the camera, search for the IP of the camera, and change the IP to the same network segment as your computer; 3. Enter the IP of the camera you found or changed with the camera search tool in the IE address bar to log in to the camera in the LAN, enter the camera settings page, and set the relevant network options. 4. Log in to your route, check whether your routing settings have the blacklist and whitelist settings enabled, and the camera must be allowed to access the Internet here; 

Pro3 I'm glad to answer your question Yo How to reconnect after replacing the router is as follows:

Directly reset the monitoring, reset to clear the cheats, according to the original networking mode, pat the right grip, and reconnect the router's wifi. Most of the monitoring is comrade, and then after the attack, he directly searched for the monitored device, and then directly connected the device to the wireless network on the mobile phone. 

1. The IP camera is powered on and connected to your road judge or switch with a network cable; 2. Under the same LAN, use the computer to open the camera search tool that comes with the camera, search for the IP of the camera, and change the IP to the same network segment as your computer; 3. Enter the IP of the camera you found or changed with the camera search tool in the IE address bar to log in to the camera in the LAN, enter the camera settings page, and set the relevant network options. 4. Climb Cong Chong Senlu your route, check whether your routing settings have the black and white list settings turned on, and the camera must be allowed to access the Internet here; 

Summary. If you want to monitor**, you need to router LAN port IP, NVR hard disk recorder and IPC camera must be in the same network segment, otherwise you can't fully present the monitoring picture without one.

If you want to monitor, then you need to sell the LAN port, IP, NVR, DVR and IPC camera must be in the same network segment, otherwise you can't fully present the monitoring picture without one.

If the monitoring is wired, you need to check whether the network cable is connected correctly, and the wireless needs to be adjusted through the monitoring app installed on the mobile phone. 1. Wireless camera: Modify and change the router's wireless wifi name, password, and LAN port settings

If you remember the wireless wifi name and password of the router before you replace it, you can log in to the router management interface through your mobile phone, change the wireless wifi name of the replaced router to the wifi name and password of the original router, and change the LAN port IP of the router to the same as the original router. Re-set the wireless camera: You can reset it by the monitoring app originally installed on the standby phone, and there is a factory reset button on the wireless camera, and you can operate according to the voice prompt after restoring the factory settings.

2. Wired camera: Computer adjustment: Modify the local connection of the computer to automatically obtain IP, open the monitoring software on the computer, select Add Device on the monitoring software interface, and add the IP point of the camera after selecting automatic search (due to different monitoring software, the specific setting method is different) Video recorder adjustment:

This repair is much more convenient,Log in to the video recorder management interface, select the system settings, select the network,Modify it in the network interface to automatically get the bird to destroy the IP address。

Summary. Your monitoring should be networked, maybe the IP address is not in the same segment, so you can't see it, change the address of the router to the same segment as the monitored address, if the monitoring is, the router is, change the router to.

This situation is caused by DHCP, the default DHCP of the TP-Link router, from 100 to 199, the default DHCP of the Tengda router, from 2 to 254, if the user used the TP router before, and set the monitoring IP address within 100, after replacing the different brand router, it may cause the router to assign the IP of the surveillance camera to the computer or mobile phone and other devices, it is recommended to assign the IP address according to the original router, and it can be normal after restarting the router.

Hello, in this case, you need to restore the monitoring to factory settings and reconnect it.

How it works. Your monitoring should be network, it may be that the IP address is not in the same segment, so you can't see it, change the address of the router to a segment with the address of the monitoring, if the monitoring is, the router is, change the router to this situation is caused by DHCP, the default DHCP of the TP-Link router, from 100 to 199, the default DHCP of the Tengda router, from 2 to 254, if the user used the TP router before, The monitoring IP address is set within 100, after replacing a different brand of router, it is possible to guide the router to distribute the IP of the surveillance camera to a computer or mobile phone and other devices, so the surveillance camera will be displayed no**, it is recommended to assign the IP address according to the original router, and the balance can be normal after restarting the router.

You can find out the original manual of monitoring, restore the factory settings according to the manual, and reconnect it.

If you change routers, you will need to reconfigure the monitoring device to connect to the new router. Here are some steps you may need to take:1

Log in to the management interface of the monitoring device. This can usually be found in the device's manual, or you can try entering the device's IP address into your browser to access the admin interface. 2.

Find the network settings or network configuration options in the Manage Mess menu. This can usually be found under "System Settings" or "Network Settings". 3.

In the network settings, locate the IP address and subnet mask of the new router. This information can usually be found in the router's manual, or you can try entering the router's IP address in your browser to access the router's management interface and find this information. 4.

Change the IP address of the monitoring device to the IP address of the new router. This can usually be done in the network settings. 5.

Make sure that the connection between the monitoring device and the new router is working. You can try to test whether the connection is normal with the ping command. 6.

If your monitoring device supports DHCP, make sure it is enabled and assigned the correct IP address. 7.Restart the monitoring device and the new router to ensure that all changes take effect.

Once you've completed the above steps, your monitoring device should be able to reconnect to the new router and work normally.