CAD in the program parameters modify the shortcut is unknown to the command is going on

What you said should have been modified, and after using it, it may suddenly not be used when you open the CAD again, because the system did not load this command, and the text that added the modification command was placed in the wrong place. The general solution to this situation is to regenerate the drawing, or turn off the CAD completely and open it again, or open the text and save it again.

1. First of all, enter the command of redefine in the interface of the CAD software.

2. Then, press the Enter key on the keyboard to confirm, so that the redefine command will appear in the status bar.

3. Next, move the mouse cursor to the icon of the insert block in the left tool.

4. After that, the mouse stays at the tool to insert the block for a few seconds, and the insert command will appear in the status bar.

5. Finally, enter Insert in the interface of CAD software.

Solution: Enter the command redefine in the CAD software and enter insert in the CAD interface.

Material Tools: CAD software.

Detailed steps: 1. First, enter the command of redefine in the interface of the CAD software.

2. Then, press the Enter key on the keyboard to confirm, so that the status bar will appear the input redefine command.

3. Next, move the mouse cursor to the icon of the insert block in the left tool.

4. After that, the mouse stays at the tool to insert the block for a few seconds, and the insert command will appear in the status bar.

5. Finally, enter insert in the CAD interface to solve the problem that the CAD shortcut key cannot be used and becomes an unknown command.

1. Enter the shortcut key for the command that cannot be used in the command line, and then click"Input"。You are prompted to enter an unknown command, followed by the full name of the order to give the car a missing order, remember it.

2. The command line loses frankly into redefining this command, remember not to lose the error. Click"Input"。The name of the input command is displayed.

3. Enter the full name of the command that cannot be used in the enter command name, remember that it is the full name.

4. Enter the shortcut key of the command you just entered in the CAD interface, and then click it"Input"。

5. If you still can't check the error for each step, your shortcut command is not available.

1. In the command line above the CAD, retrieve the "Tools" bar and fiber source.

2. Select the last item "Options" on the pop-up page in the toolbar.

3. Select "Selection Set" in the various menus in the options.

4. Tick the dialog box in front of "Select before execute" in the page mode, click "Confirm Jujube", and it will be successfully solved. If it's a bug with the software, it can be easily solved. If not, refer to the following methods.

5. Carefully check whether these shortcut keys have bad contact phenomenon, whether they can be used on other software, if not, you have to repair the keyboard.

1. First, type the shortcut key of the command that cannot be used in the command line, and then press the Enter key. You are prompted for an unknown command, and then enter the full name of the command you want to remember.

2. Command line input to redefine this command, remember not to make mistakes. Click the Enter button. The name of the input command is displayed.

3. Enter the full name of the unavailable command in Enter Command Name, remember that it is the full name. Click the Enter key.

4. Enter the shortcut key of the command you just entered in the CAD interface, and then click Enter.

First, use the latest 360 antivirus to scan the whole disk. Open CAD2009 under the administrator privilege, click Tools in the menu bar - Customize - Program Parameters (, copy a file from other normal computers, overwrite the original, save and close. On the command line, type reinit and put a checkmark in front of the pgp file and click OK.

I rely on all I can think of, you've already said it above, and it seems that there is no way to reload. I still can't think of a way to see your high score.

All shortcut commands defined by :CAD are saved in a file in the support subdirectory of the AutoCAD installation directory. The name of the shortcut command, *the full name of the command, such as:

co, copy is to type a shortcut command, and then type a comma and the full name of the command replaced by the shortcut. You can go inside to modify your shortcuts.

Enter the OP shortcut command, or click on the Tools option in the menu bar, go to the "Options" menu and find the "Open and Save" column under the "Options" menu. Under that bar, find "ObjectARX Applications" on the right side

Select "Object Detection and Command Invocation" in the first drop-down box under the object, and click "Apply" under the entire Options menu.

Take the Property command as an example. Enter the shortcut key of PR or CH or MO before, and the "Unknown Command" properties is displayed. Press F1 to view help. ”。If you enter it later, you will open the Properties menu directly.

This is the case with mine, turn off the CAD and go back in and you can continue to use it.

Individual CAD commands are invalid, and these commands can be used for other diagrams, only this diagram Individual CAD commands are invalid, and you can find a CAD antivirus software to kill the poison.

The most primitive way is to install CAD software from the beginning. Or reinstall your computer system! Hee-hee, that's probably the most practical.

Are all commands unknown? If it's all of them, you'll be poisoned.

1) If it is an individual command, just add a dot before the commandIt can be used.

2) You can also enter the command to redefine the recovery that was turned off.

3) Of course, you can also use the unredefine command to close it.

I recommend you to take a look at the book "The Secret of AutoCAD Masters Not Asking for People", which can be used for specific problems, not tutorials, for people who have worked, excellent Amazon, Dangdang.com have them.

The tool opens and save.

Select the first one, and then restart.

Open a small file after booting up and re-select the fourth one.

Every time you do it, you must click Apply