What does it mean when the telecom cat is disconnected and then the ADSL light keeps flashing and ca

ADSL flashing indicates that the ADSL connection is activating. Please press the following settings: 1) Plug in the power cord of the wireless broadband router for device installation, and the power indicator and WAN port light on the wireless broadband router will light up normally.

Plug one end of the network cable into the LAN port of the router and the other end into the network cable interface of the computer. 2) Configure the router to enter the browser address bar on the computer, user name: admin password:

admin。The address of different routers may be different, but it is generally written at the bottom of the router and on the router manual. After logging in to the router, there is generally a connection wizard, according to the connection wizard, at this time you will be asked how to surf the Internet, the family is generally adsl virtual dialing (that is, pppoe), select this, and then fill in and password, step by step to do it.

Hello, the ADSL indicator is always on under normal circumstances, when it flashes, it is generally a fault in the broadband line, the user can call the telecom customer service for feedback and fault reporting, and there will be staff to come to the door to troubleshoot after the fault report.

1. Check whether the optical fiber interface plugged into the optical modem is loose, and if it is loose, plug it back in.

2. Restart the modem, cut off the power supply to the modem, wait for a few minutes, and then turn on the power.

3. There is a problem with the optical interface of the optical modem, and the optical modem needs to be replaced.

4. Your broadband payment is in arrears. Nowadays, broadband is basically a postpaid model, because you have been in arrears for too long, and the operator directly turns off your broadband socks, in which case you need to pay off the arrears to recover.

5. After completing the previous method, if the optical modem still flashes the red light, then it is recommended that you call the customer service of the broadband operator**, report the fault, and ask the stupid operator company to send someone to overhaul the broadband.

As long as the ADSL light flashes, it proves that the ADSL is not connected, 90% of the reason is that the external line has poor contact, and it is possible to find Unicom or Telecom to check the line.

I am Unicom adsl from time to time to drop the ADSL light flashing to find Unicom to check the line before and after a month to change the line at home to change the connector to change the distributor to change the cat to change the router Let him change the line of the cage to the ** bureau Now it's OK At that time, the expatriate in my home saw me call him ** and had a headache o( o Now the network speed is fast Hang the adsl light for a day without flashing Hehe.

There are five possible causes of failure:

First, the ADSL modem or separator is faulty. Faulty quality of ADSL modems or separators will result in frequent drop-off failures. It is recommended to borrow a set of equipment that can be used normally, and replace it before testing.

Second, the ADSL line is faulty. The residence is far away from the local computer room (usually less than 3000 meters), or there are serious interference sources near the line, which will also lead to frequent dropouts. In addition, it is recommended to use twisted pair wires between the junction box and the ADSL modem, and even if parallel wires are used, they should not exceed 5 meters.

Third, indoor electromagnetic interference. Severe electromagnetic interference in the room (e.g. cordless**, air conditioners, washing machines, refrigerators) may also cause communication failures, it is recommended to keep the ADSL modem away from the above equipment, and do not share a power cord with the above equipment.

Fourth, the network card is defective. Defective network card quality, or drivers that don't match the version of the operating system, can also lead to frequent drops.

Fifth, the PPPoE issue. This is a problem caused by unreasonable installation of PPPoE software in the system or poor software compatibility.

If there is a problem with the line, or the moden is broken, it is recommended to call 10000 and ask the maintenance staff to come to deal with it.

There are many models of telecom cats, including Huawei, ZTE, and ASUS, I don't know which model your cat is, and in which direction the second light is counted. But yours should be the adsl external line indicator, try to turn off the cat for a while, unplug the power plug, and then restart, just press that "reset.""and see if you can get on. There may be long-term development heat.

When the modem is normal, most cats will have 3 lights that stay on without flashing, which are the power light, the ADSL external line indicator and the local connection indicator.

1。Power indicator (generally identified by PWR and power), the light will be always on after the power supply is added, if it does not light up, it means that there is a problem with the power supply of the cat.

External line indicator (generally identified by adsl, dsl, line, link, wan, status, etc.), the ADSL signal is connected to ADSLMODEM through the external line, and the light will always be on when it is connected to ADSLMODEM normally.

3。The local connection indicator between the user device and ADSLMODEM (generally identified by PC, LAN, 10M, 100M, and Ethernet) will always be on when the physical connection between the device and ADSLMODEM through the network cable is normal. (Note; Different cats have different requirements for network cables, try to use the original network cables).

4。The data transceiver indicator (generally identified with TX, TXD, RX, RXD, DATA, RUN, etc., some models may not have it), will continue to flash when there is data transmission; It doesn't light up when there is no data transfer or it flashes every once in a while, depending on the model of the cat.

If the ADSL external line indicator does not light up or flashes, it means that there is a problem with the line. The reasons for the flickering are: the ** wire connection between the cat and the separator is incorrect or poorly contacted; There is a problem with the separator; There is a problem with the outer line; Whether there is high-power electrical interference next to the cat, it is recommended to check whether the line between the cat and the separator is connected, because the ** wire connector is often in poor contact due to moisture and rust, it is best to unplug and check and reconnect.

If you wait for stability, you can access the Internet; If it still doesn't light up or flicker, there may be a problem with the outdoor wiring. You can call 10000 to report for repair.

If the local connection light does not turn on, it may be: the computer is not turned on; The network cable connecting the network card and the cat is not well connected; There may be a problem with the network card. Please check whether the network cable between the cat and the network card is connected, after confirming that it is connected, if the local connection light is still not on, you need to check whether there is a problem with the network card, maybe the network card of the computer is loose or broken.

If the above inspection fails, call 10000 for repair. Telecom will come and give you a cat for free.

Dear users, hello!

According to your description, your telecom cat flickering is not normal, most likely it is a line problem, you can call 10000 for broadband failure repair, telecom maintenance master will come to deal with it for you at the specified time, please wait patiently! If the above information does not solve your problem, you can also log in to Anhui Telecom Tianyi Store (

The average cat has four lights, one is the power power, one is the link is the connection light, the LAN is the network cable light connected to the computer, and finally the ACT will flash when there is data transmission. If the second one is link, it is not connected to the remote server. With the error code given when dialing, call 10000 to report for repair, and they will help you faster.

Call 10,000 and let them come to the door.

This indicates that the network port of the modem is connected to the device, and the device is networking and has data exchange.

The above information is for reference only, gigabit in the city, C-position debut. 5G dual gigabit**, 1000M broadband, 60G traffic for the whole family, details can be found in Guangxi Telecom's online business hall. Customer service number 43 will answer for you.

Hello, if there are other devices connected to the network port 1 to surf the Internet, the indicator light of the network port 1 is flashing normally, and if the broadband can not be used, you can try to restart the fiber optic modem.