Urgent This morning, the hard disk light flashed red and kept ticking the alarm. . .

Check the various hardware connections of the machine, and it would be better if there was a checker card

It's possible that it's not a memory module or something, and it's not plugged in tightly, or look at the cards in the chassis that are plugged in tightly.

1: The hard disk light will flash when the project is loaded at boot.

2: It will flash when running the program.

The above two situations will not flash after a period of time, which is normal.

3: It is abnormal when the hard disk light flashes and there is a sound.

4: It is also abnormal to keep flashing when the program is not loading or running.

In both cases, you need to be aware that there may be a problem with your hard drive.

Enter msconfig in "Run", click on the "Start" tab, and turn off all the programs that do not run automatically. View the original post

It may be a graphics card problem, or it may be a display problem, you can take a look at the driver first, enter the safe mode to see if it is still not like this, if it is still like this, it is estimated that it is a hardware problem.

Normal No big deal.

The hard disk light flashes non-stop, indicating that there is a program reading and writing data on the hard disk. Such as hacker infiltration, virus programs are running, planned tasks are being executed, etc. What exactly is the program running?

If you are unsure, you can disconnect the network and call the process manager to see what program is running. If there is a suspicious process in the process, immediately abort it and enable security software to scan it.

1.If you use the NTFS file format, the disk will be automatically defragmented when idle.

2.When you are idle, the system will automatically index the files to speed up your search for files.

Read your chat history including images and much more.

If you don't flash, you're still afraid!

You have to know that hard disk lights don't mean that staying on is working! As long as there is a change in the data, the hard disk light is flashing, if it does not flash, it means that the hard disk is not working, that is, it is dead! So it's normal for the hard drive to flicker!

It's normal to flash, it's the hard disk reading and writing data. It is no wonder that the installation system is not sensitive, and it is not surprising that it is sensitive to a flash hard disk light. 360's strength is to kill Trojans, its anti-virus engines are still borrowed from abroad, there is no professional R&D team, and there is a lot less R&D funds.

So it's free! Like Rising Kaka, the function of Rising Kaka is the same as that of 360, they are all Trojans, and it is also free. But you know, Rising also has its own anti-virus software, which costs money.

If you use a Trojan software to kill viruses, you can imagine how effective it is. As for Kingsoft didn't find out, you don't have to reinstall the system, you can try other antivirus software, I myself use a foreign one, Kaba nod32 ......These are all good. If the other one doesn't have any effect, maybe you're really sensitive!

Remember: antivirus software can sometimes give false positives!

There was a problem with the windos system boot phase, and the system was reinstalled.

It should be what data the hard disk is reading and writing, etc.

When you turn on the computer, the hard disk light of the computer has been flashing, that is, when the computer is not in use, it will also flash, and when the computer is overburdened, it will lead to a certain failure of the hard disk to run overload for a long time

1. Reduce the burden on hard disks.

1. Stop unnecessary service programs on the computer to reduce the pressure on the hard disk, open the start menu to find the run option, enter in the text box and click OK.

3. Click and double-click the service items, and select the disable option in the pop-up dialog box to disable these services.

2. Shut down special processes.

1. Right-click on the blank space of the taskbar at the bottom of the computer desktop and select the Task Manager option;

2. Find some processes with large memory occupation and large file read and write volumes, and end these processes to reduce the pressure on the hard disk;

3. Defragmentation.

1. Open My Computer on the desktop, enter the computer drive letter interface, right-click on the disk of our computer, and select Properties to enter the property setting dialog box;

2. Then find the tool option in the toolbar above, click to enter, you can see the defragmentation function item, click on the rear to defragment immediately;

3. Enter the defragmentation interface, click Disk Defragmenter in the lower right corner to start sorting our disk casually (the defragmentation process may be very long, patience, etc.).

The hard disk light keeps flashing, indicating that the hard disk has been reading or trying to force the data to be read for unknown reasons, and according to the existing conditions, it is judged that the power supply has burned and affected the hard disk.

First of all, quickly back up your important data, and then use hard drive detection software to check the hard drive to see if there are any problems. If there is no problem, just use it. Because the hard drive usually doesn't break down suddenly, it's not a big problem, and I'll talk about it when something is abnormal.

Generally, hard disk damage is motor failure, 0 track damage, bad track these kinds of faults, if there is no problem with the track, then pay attention to frequent backup of the main data.

The impact of the power supply burning radio wave on the hardware is different, so it is impossible to determine the specific cause of the fault according to the existing conditions, and if the hard disk motor is impacted by the current, the degree of damage cannot be accurately judged.

So, do what you can do, then back up your data, and then use it with peace of mind. In the future, you can often observe whether the lights of the hard disk have changed.

It's all flashing when it's working normally.

If it always flashes when you first turn it on.

The system is loading files.

Normal. If it keeps flashing.

Virus. Or a G-rated file was copied.

There is also a possibility that the memory of the machine is too small and the CPU is too high.

Read-in and read-out streams do not have sufficient memory allocation, and can only be accessed to the hard disk through frequent access.

to be able to solve it.

When the hard disk does not read or write data.

The hard drive indicator should not be flashing. See if there's a virus. The computer doesn't seem to be as fast as it used to be.

It's more like there's a virus.

It's normal for the motherboard to have a boot logo, and the three major brands have this.

Your hard disk light keeps flashing has little to do with the motherboard, and the motherboard doesn't read the hard drive's data. It's not surprising that you have to read your hard drive to surf the Internet, write documents, and run any program, and the lights are flashing.

The reason why the hard drive light keeps flashing.

For example, some antivirus software may be set to automatically check for viruses when the computer is idle, or some defragging software may automatically defragment the disk. There is a lot of normal software that will operate when the system is idle.

Of course, the possibility of viruses is not ruled out, and there is no antivirus software?

Friends said. The hard drive has bad sectors. It's also possible that there is a problem with the power cable that connects your power supply to the hard drive.

Causes the power supply to be unstable and crashes. It is recommended that when you take it over for repair, they will scan the hard drive for you to see if there are any bad sectors. If there is a bad sector.

Fix it early. The later it is, the harder it is to repair. If it's something else.

Just let the shop that helped you fix it last time will help you solve it. Once you have collected the money, you have to get things done. Otherwise, it will continue to crash like this.

Even if there are no bad sectors on your hard drive, the bad sectors will be removed. Hope mine can help you.

That interface can be turned off in the BIOS.

i, let's kill the virus after reworking the system. We all know that the virtual memory of a computer is greater than the physical memory, what does that mean? When your computer is poisoned or your physical memory is eaten up due to other work, it will keep flashing on your hard drive because a part of your hard drive has been used as virtual memory.

The speed of the hard disk cannot be compared with the memory, so it is very slow and "flashing".

ii,"ASUS K8N4-E SE interface" is the boot logo (advertisement), press F2 when starting the computer, then look for boot setting in the boot options to find the option with the word logo, set it to disabale, and finally press F10+Enter on the line.

iii. Give points.

It's a problem with the BIOS settings, maybe your motherboard BIOS is older, and the hard disk is relatively large. It's okay, don't worry.