How about raising the strength of WIFI

How to increase wifi signal strength by 2 times.

WiFi strength collapse,Generally speaking, it is only related to routing,Methods to improve the strength of mobile phone WiFi:

1. Use enhanced antennas or directional antennas to enhance the transmission signal.

2. Open the back cover of the mobile phone when receiving the wifi signal, generally speaking, the antenna of the wifi is near the battery.

3. The distance between the location of receiving wifi and the wifi source also has a certain relationship with the mobile phone, theoretically the closer the better. Normally, the wifi signal within 5 meters is full.

4. Try to place the router in a relatively high place at home. The signal is transmitted from high to low at the fastest speed, and it will not be hindered by too many obstacles when coming down from a high place. Cover Hui.

5. Keep the router away from the wall.

6. Modify the factory settings of the router. Most of the newly bought router manufacturers set the speed of 70%, and if you want to make the wifi faster, you can adjust it to 100% speed.

1. It is recommended that you check whether the mobile phone uses a metal protective case, a magnetic protective case, a magnetic bracket or a magnetic chuck.

2. There are two main ways to enhance the WiFi signal: set the restart time for the router. If you have to restart your router every now and then to prevent it from disconnecting, there is such a way to deal with it.

3. Change the signal channelWhen using a wireless router, usually the router will default to a channel, which may be the most congested. So, you can change the channel in the wifi settings in the router's background management page, and switch to a less crowded channel.

4. Check the mobile phone caseIf your mobile phone uses a metal or magnetic protective case or bracket, such a protective case and a celery stand have an impact on the WiFi signal, it is recommended that you take it off and try it.

5. Replace the router and turn off other wireless devicesThe router is the transmitter of the wifi signal, and its performance has a great impact on the strength of the wifi signal. If your router is old or not performing well, then your wifi signal will become weak. To boost the wifi signal, you can consider replacing your router.

Dear users, hello:

Here's how. 1. Adopt the highest speed setting supported by the device.

Enter the router settings interface and set the wifi parameters. Set the speed of the wireless network to the maximum speed supported by the network device, that is, set it if the device supports it, set it if it does, and try not to set it to this form.

2. Set the MIMO enhancement mode.

If the wireless router supports MIMO Enhanced Mode, please also check this option on the settings screen, and then set the "Bandwidth" to "20 40MHz" (select the highest setting). However, not all routers that support MIMO have this option, if you can't see this option, just set the bandwidth.

3. Enable QoS control.

Here's how you can boost your WiFi signal:

1. Update your WiFi device.

2. Set the best channel:

1) Log in to the router's management page;

2) Click "Basic Settings", change the "Default Channel", and select another better channel.

3. Adjust the position:

1) a central location in the home;

2) Keep away from interfering equipment;

3) Reasonable placement of antennas.

Fourth, prevent the outside from rubbing the net.

Fifth, the installation of auxiliary settings.

1. Position the wireless router reasonably.

Since the wireless signal is greatly attenuated after crossing obstacles, especially through metal. In our family's house, there are a lot of reinforced concrete walls, so when we place the wireless router, we should make sure that the signal passes through the wall as little as possible.

2. Modify the signal channel to reduce interference.

In the configuration interface of the wireless router, we will see the wireless channel option. Generally speaking, there are 11 wireless channels of 54m, which are channel 1 to channel 11. Signal interference occurs when multiple wireless signals are using the same wireless signal channel.

Many users do not modify the wireless signal channel after purchasing a wireless router to use, so everyone uses the channel when the router is configured by default, so that channel interference is easy to occur. If there are neighbors in the vicinity who are using the same channel as ours, then the wireless signal for both of us will be affected. We can also use the Network Stumbler software to scan to see what wireless signals are nearby and which channel is being used.

Then we make modifications to our own wireless channels to avoid duplication with other channels.