-
Sakura" electric hot water faucets can be divided into two categories according to different water inlet methods, one is the letter C at the end of the model, such as 1C, 4C, 7C, we call it side water intake, which is directly fixed and installed on the water pipe; The other type is the letter D at the end of the model, such as 1D, 2D, 3D, 5D, 6D, 9D, we call it the bottom water inlet (used to call the bottom inlet water), which is directly fixed and installed on the basin, and is connected to the water pipe by a hose.
According to the different water inlet methods, that is, there are two installation methods, and the installation is very simple, and it can be completed by yourself without the need for professionals.
Side inlet type C: Take JDR-4C as an example.
Lower water inlet type D: Take JDR-2D as an example.
Tips: After connecting this product to tap water, first turn on the faucet (hot and cold position), see water sprayed out of the nozzle, and then connect to the power supply, that is, the first use needs to be powered on after the water is turned on, and it is not necessary to use it in the future, and there is no need to unplug the power cord.
In addition, there are two different ways to install the power cord of the "Sakura" electric water faucet:
Side inlet type C: The power cord can generally only be surface-mounted (i.e. the electrical socket is above the basin).
Bottom water inlet type D: The power cord can be installed openly or concealed (i.e. the power socket is under the basin and hidden inside the cabinet or bathroom cabinet).
"Sakura" electric hot water faucet can be widely used in:
Families, hotels, guesthouses, shopping malls, supermarkets, office buildings, restaurants, beauty salons, schools, hospitals, nursing homes and other public institutions and government organizations, factories and other enterprise units, installed on kitchen sink basins, bathroom wash basins, replacing the original ordinary faucets, only need to connect to tap water, plug in the power supply can be independent terminal heating.
Description of the concealed installation method of the power cord:
1) Pry the small hole cover sheet reserved on the side of the machine base against the power cord from the inside to the outside with a screwdriver;
2) Thread the power cord through the small hole and gasket in the base of the machine;
3) Thread the machine inlet pipe and power cord together under the basin to be installed;
4) Cover the water inlet pipe with the wire rack and set up the power cord, and then tighten the fixing nut around the water inlet pipe;
5) Connect the power cord to the plug and plug it into the power socket.
-
Electrically heated faucets are provided by the factory for installation.
-
1. Installation of single-hole basin faucet:
When buying a single-handle basin faucet, you should pay attention to the diameter of the water outlet, most of the water inlet on the market now belongs to the hard pipe, so you should pay attention to the height of the reserved water inlet, 35 minutes from the basin down is the most suitable. When installing, a special angle valve must be selected, and the angle valve must be fixed with the cold and hot water pipe of the wall outlet. When you notice a distance between the angle valve and the faucet water pipe, go and buy a special extension pipe to connect.
Remember, be sure not to use other water pipes to connect, because if the water pressure is high, it can easily fall off and leak, causing you losses. If the inlet pipe is too long and exceeds the outlet pipe, you can cut off the part according to your needs, and if the angle is not suitable, you can bend it moderately to the position you need as needed. Remember:
Do not bend hard to 90 degrees or greater than 90 degrees. When installing the basin to drain the water, do not forget to buy a small connector (short to the faucet). Don't forget to rinse the water pipes buried in the wall before you install them.
Second, the installation of shower and bathtub faucets (wall-mounted):
Once you've purchased a shower, bathtub, or wall-mounted faucet, you can choose the right height for your plumbing. The spacing of hot and cold water pipes must reach 15 cm. Don't forget to rinse the water pipes before installation, so as not to damage the faucet due to the water quality.
Concealed shower and bathtub faucets: After purchasing concealed faucets, the valve core of the faucet should generally be embedded in the wall. Be sure to pay attention to the thickness of the bathroom wall before embedding.
If the wall is too thin, the spool will not be able to be buried. Do not easily remove the plastic protective cover of the valve core when it is buried, so as not to damage the valve core with cement and other chores during the embedding. In addition, when the valve core is embedded, you should also pay attention to the direction of the valve core up and down, left and right, so as to avoid the valve core being buried wrong.
If there is a deviation in the size of the wall-mounted faucet when the water inlet pipe is embedded, it can be adjusted with an adjustable crutch for calibration.
Third, the installation of thermostatic faucets.
Before installing the thermostatic faucet, please check whether the water pipe is hot on the left and cold on the right, and remember not to connect the hot and cold water pipes incorrectly, so as not to prevent the faucet from working properly. Gas and solar water heaters cannot use thermostatic faucets because the water pressure is too low. When installing a thermostat, don't forget to install a hot and cold water filter.
Fourth, the installation of single-hole kitchen faucet.
It is required to be stable, because the kitchen faucet is used more frequently, and it is easy to loosen when it is moved around, so the lock nut must be tightened. At present, there are some faucets on the market for the solenoid to increase the nut fixation, this kind of stability effect is very good, if you can solve the problem of water lifting, it will be a popular trend in the future.
Prepare the installation tools, check whether the supporting parts are complete before installation, common faucet spare parts are: hoses, rubber gaskets, showers, water removal, crutches, decorative caps, etc.
-
The rubber ring must be placed accurately, the raw material belt should not be used too much, and the power supply should not be directly below the pool, and the leakage protector should be installed.
-
You know a lot, before installation, it is best to temporarily connect the water and electricity to try it, no leakage, no leakage on Europe, the materials are ready, it is best to keep the original faucet, the electric hot water faucet is still not easy to use when using a large amount of cold water. The electric water faucet can only be used as a spare item and is used occasionally.
-
You can ask the seller, some of them have an installation process on the manual
You can spray the fastened bolts of the faucet with a rust remover to make the bolts moisturized and easy to disassemble. >>>More
Water leakage is a problem that every family can encounter. If it is not solved in time, it will not only waste water resources, but once it is discovered in time, the consequences will be unimaginable. >>>More
At present, there are three types of spools on the market: copper spool, stainless steel spool and ceramic steel spool. >>>More
Mona Lisa monnal faucets are of very good quality, pure copper, durable, and have a good feel and texture.
Purchase tips to give you a few useful and concise: 1. Turn the handle: feel light and good 2. Look at the appearance: >>>More