One of the Vantage gas stoves is normal, and one is on fire for a while, and the two will be complet

The induction needle is broken or the circuit is broken, causing the flame-out protection device to start.

Vantage gas stove is a brand product of Vantage Gas Appliance Co., Ltd. On November 28, 2001, Zhongshan Vantage Gas Appliance Co., Ltd. was established. On September 19, 2003, Vantage gas cooker was the first to pass the national review and obtain the production license; On April 28, 2006, Vantage Co., Ltd. became the exclusive supplier of gas appliances for the 2008 Olympic Games in Beijing. In March 2008, Vantage Co., Ltd. became the manufacturer of the Xiangyun torch of the Beijing Olympic Games; In April 2009, Vantage became the kitchen and bathroom sponsor of the 11th National Games and exclusively provided the 11th National Torch; In March 2010, Vantage became the torch manufacturer of the first Youth Olympic Games, and in August this year, the torch made by Vantage will once again shine on the international stage.

The problem in my house is similar, mine is a normal one, and one turns off automatically after 30 seconds. I think I think the induction needle is broken or the circuit is broken, causing the flameout protection device to start. Hehe, but now the question is how to take it out?

I looked at the needle as if it had been fused with the stove.

1) Connecting pipe flattening or bending;

2) Flattening or bending of the connecting pipe;

3) The battery is low and the discharge frequency is slow;

4) The gas outlet pressure is unstable, too high or too low.

It may be the reason for the damper under the gas stove, one is normal, the other is not adjusted, the gas intake is too large when used, the fire is not strong, and the gas safety device is started to extinguish!

Vantage gas stove, a garbage product, if there is a problem, it will not be returned, and whoever uses it will regret it.

This situation is due to the fact that the gas stove has turned on the flame-out protection function, and secondly, it is possible that the reaction is sluggish due to the overflow of the pot when cooking the rice balls. There is also the gas stove air pressure is too high, causing the air flow speed to be too fast.

1. This situation may be due to the flame-out protection device not sensing the flame. The bezel is not opened. The resulting gas is not ventilated. In this case, the gas valve should be closed immediately. Then replace the flame-out protection induction pin.

2. In addition, if the phenomenon of overflowing the pot occurs during cooking, the gas outlet will be blocked, at this time, it is necessary to clean up the outlet of the gas stove in time, wait for drying, and then turn on the gas stove. This is also a protective function for the gas stove to be turned on. Secondly, it is necessary to check whether the battery is dead.

In the daily use of the stool Hu gas stove, it is necessary to clean the oil stains and stains on the natural gas stove.

3. Check whether the air pressure of the gas stove is too high, and the airflow speed is too fast. If the fibroids are too collapsed, they will quickly impact the electric spark, in fact, it is also possible that the ignition nozzle is too large and the airflow is too much. This is where the right nozzle needs to be replaced.

4. Check whether there is wear or impact inside the switch assembly, and the pulse ignition assembly switch is in poor contact. It will also cause the phenomenon of not ignition, check whether the natural gas hose is folded in half or blocked. If it is folded in half, it needs to be smoothed out in time, and if there is a blockage in the pipe, the pipe needs to be cleaned in time.

The natural gas switch needs to be disconnected while checking for problems.

Summary. If there is a normal one, there is no problem with the battery. There is a strong smell of gas, which means that there is no problem with the pipes either.

1. Wipe the lighter needle and the corresponding stove head with a cloth, and if the dirt and rust are serious, use sandpaper with water. 2. Embedded disassembly panel, desktop lifting, check whether the line on the fault side has fallen off. 3. Use a multimeter to measure whether the micro switch behind the knob in the circuit is invalid or in poor position.

Vantage gas stove one can't be hit, one is normal, what should I do?

There is a return to the circle that is normal, indicating that there is no problem with the battery. There is a strong smell of gas, which means that there is no problem with the pipes either. 1. Wipe the lighter needle and the corresponding stove head with a cloth, and if the dirt and rust are serious, use sandpaper with water.

2. Carefully disassemble the panel with embedded disassembly, lift the desktop, and check whether the line on the faulty side has fallen off. 3. Use a multimeter to measure whether the micro switch behind the knob and Shijing in the circuit is invalid or in poor position.

1. Clean up the root of the high-temperature metal wire of the lighter, which may flow there due to the overflow of liquid in the pot, so that the insulation is poor and the spark is not strong. It can be compared with another normal one. 2. The distance between the high-temperature metal wire and the stove should not be too close or too far.

If the distance is too far, the spark is weak, or there is no fire; The distance is too close, the sparks are short, and it is also not easy to ignite the fire. 3. The size of the damper should be appropriate. The damper opens wide and is not easy to ignite; The damper is small, there will be a yellow fire, and the burning trousers are not full of rounds.

It may be caused by the following original collapsed hole beams:

1.Gas pipeline is not blocked: Check if the gas pipeline is blocked or if the gas valve is open.

2.Flame sensor failure: Check if the flame sensor is clean and if there is dirt that needs to be cleaned or replaced.

3.Spark plug failure: Check whether the spark plug is clean and if there is dirt that needs to be cleaned or replaced.

4.Insufficient gas pressure: Check if the gas line has enough gas pressure.

5.If the gas stove is used for too long, the thermal elements of the gas stove may deteriorate and need to be replaced.

It is recommended that you contact a professional maintenance personnel for inspection and repair.

Summary. Hello, dear! 1. The pulse needle has no battery; The air source switch is not turned on or the air pressure is insufficient.

2. Ignition electrode, improper distance of induction electrode or pollution; The air pressure is too high, causing the air flow to be too fast, and the impact is sparked. 3. Piezoelectric ceramic aging; The ignition output cable is not firmly connected with the porcelain head; The output cable is damaged, causing a super-close ignition. 4. The ignition nozzle is too large, and the nozzle is too large to cause too much airflow and impact the electric spark; The head is damaged, resulting in ignition at a very close distance to the damaged part.

5. The internal impact block of the switch total is worn or broken; Poor contact of pulse ignition total range micro switch; Cobwebs in front of the ignition nozzle or in the ignition support; The hose is twisted or clogged.

Hello, dear! 1. The pulse needle has no battery; The air source switch is not turned on or the air pressure is insufficient. 2. Ignition electrode, improper distance of induction electrode or pollution; The air pressure is too high, causing the air flow to be too fast, and the impact is sparked.

3. Piezoelectric ceramic aging; The ignition output cable is not firmly connected with the porcelain head; The output cable is damaged, causing a super-close ignition. 4. The ignition nozzle is too large, and the nozzle is too large to cause too much airflow and impact electric sparks; The head is damaged, resulting in ignition at a very close distance to the damaged part. 5. The internal impact block of the switch total is worn or broken; Poor contact of pulse ignition total range micro switch; There are cobwebs in front of the ignition nozzle or in the ignition support; The hose is twisted or clogged.

The battery is charged and extinguished after 7,8 seconds after ignition. What is the reason for the continuous ignition?

The reasons for the general fire all the time are:1The compression spring of the switch is not elastic, or the elasticity is weak, and it cannot return to the original; 2.

The high-voltage electronics are broken; 3.The contacts of the switch are broken; 4.The solenoid valve was not opened, and the air source did not flow to the fire hole; 5.

The thermocouple and the solenoid valve do not form a circuit loop; 6.The flame-out protection device is damaged. Constant Ignition Solution:

1.Replace the gas stove switch with a new one; 2.replacement of the igniter with a new one; Qi Xianxiang 3

Check whether the connecting wire of the solenoid valve is well connected; 4.Adjust the position of the thermocouple so that the fire temperature can affect its normal use; 5.If the flame-out protection device is broken, then replace it with a good one.

For details, please call us or make an appointment for repair.

That's it after cooking and throwing the pot.

Change the switch. That's it.

Can I change it myself?

No, it's warranty.

Hello. The reasons why the Vantage gas stove is extinguished after a while The reasons why the Vantage gas stove is extinguished after a while are as follows: 1. The battery is too low or the power is used up; 2. Let go too quickly when ignition; 3. The fire cover of the gas crack-resistant stove is blocked or the carbon deposit of the needle is protected.

Solution: 1. If the battery is too low or the power is used up, it will be extinguished after a while, and the battery in the stove needs to be replaced in time. 2. It may also be caused by letting go too quickly when using an electronic lighter gas stove, because the electronic lighter gas stove basically has a flame-out protection device, and you need to hold it down for about 5 to 10 seconds after ignition, until the induction needle takes effect before you can let go.

3. It may also be that the fire cover is blocked or the protective needle is deposed with carbon, the fire cover is clogged and needs to be cleaned and closed with iron wire in time, and the protective needle should be polished with fine sandpaper after carbon deposition.