Stainless steel baseboard installation method for stainless steel baseboard

Floor tiles, gray, white dark flower wallcovering, want to paste gray brushed or solid black stainless steel baseboard. How can there be a reliable manufacturer? Coordinates Xi'an.

1. Preparations.

1. Make a positioning ruler: when installing the buckle, use the positioning ruler to determine the height of the installation position of the buckle. The length of the positioning ruler is 1000-2400 mm; width 40-50 mm; The height depends on the baseboard model, the height of the T70 is 17-mm; the height of the t80; T100 height 38 - mm; T110 mm high; The positioning ruler can be made of wood or iron.

2. Clean the wall foundation: remove the cement floating blocks protruding from the wall, corner and wall root of the baseboard; Check the straightness of the wall, the maximum gap is not more than 3 mm. No, the convex part of the wall should be leveled. Gaskets should be added to the recesses of the wall.

Second, install the buckle.

1. Installation method 1 (cement row nail fixation): put the buckle on the positioning ruler, against the root of the wall, press down the upper end of the buckle with your fingers, and fix it with a nail gun, see Figure 1. Cement row nails are 32 mm long; The spacing between the buckles is about 400 mm; There should be a buckle at the interface of the two baseboards; There should be a buckle at the end of the wall about 30 mm.

2. Installation method 2 (percussion drill punching fixation): fix a drill die on the positioning ruler (the diameter of the drill hole is slightly larger than the percussion drill bit), resist the wall root, and drill a hole in the wall with a percussion drill; Insert a wooden needle or plastic tube into the hole. When fixing the buckle, it is still necessary to use the positioning ruler to adjust the buckle and fix it at the same height (using the waist round hole on the buckle).

The rest is the same as above. 3. Description: The wooden wall or gypsum board wall should be fixed with a carpentry nail gun; The plaster wall can also be fastened with self-tapping screws using light steel keels.

3. Install the baseboard profile.

1. After ensuring that all buckles have been installed on the same straight line (error mm), cut the material and cut the yin and yang corners according to the size (leaving about 2 mm seams for silicone mud seams), and grind off the burrs. Then tear off the protective film above and below the baseboard to allow for a silicone seal. Neutral silicone is used for sealing and mud seams, and its color is usually silver-gray or white.

2. Hang the groove on the baseboard of the lower size on the upper mouth of the buckle at an inclined half, and then lift the back end of the baseboard up a little and then press down against the wall, so that the upper convex card of the buckle completely enters the groove on the upper part of the baseboard, and at the same time tap the middle of the baseboard, see Figure 2. When installing, start from one end, and press one buckle to the other end step by step, and do not hammer it.

3. After the installation is completed, the gap between the baseboard and the wall and the ground is sealed with silicone, and the yin and yang corners and the 2 mm gap reserved for flat joints are pasted with masking paper and then made silicone mud joints.

4. Tear off all the protective film of the baseboard, wipe off the residual glue of the stainless steel veneer with old powder, and use a brushed cloth to remove the black spots formed by the heating of the glue at the incision.

5. The use of stainless steel yin and yang angles is more convenient to install, and customers are welcome to choose. Its installation method: after the installation of the baseboard is completed, the female corner, male angle and head can be glued to the joint with AB glue.

When installing tiles, it is necessary to install a baseboard between the wall and the ground, and the baseboard is different according to the material, and the installation steps are not the same, because the stainless steel material gives people a cold and hard feeling, in order to be beautiful, special attention needs to be paid to the construction fineness when installing the baseboard of stainless steel, and the installation steps are more complex than that of wood and PVC material. Many residents have problems such as falling off after installing the stainless steel baseboard, which is very troublesome, and today I will introduce you to the installation steps of the stainless steel baseboard.

Stainless steel baseboard mounting.

1. Preparation of stainless steel baseboard installation steps.

Before installing the stainless steel baseboard, you need to make the corresponding preparations, and this preparation is mainly to clean the wall foundation and make the positioning ruler. The positioning ruler is used to determine the length and height of the buckle installation, so the positioning ruler needs to be prepared before installing the stainless steel baseboard, and the general positioning ruler is made of wood or iron, according to the model of the baseboard.

The wall base is the foundation for installing the baseboard, so it is necessary to ensure that the wall base where the baseboard is installed is flat and neat. Before installation, remove the burrs and cement on the wall, corners and wall joints in advance, especially the corners of the wall. Secondly, it is also necessary to check whether the wall is straight and whether the gap is more than 3mm.

2. Installation buckle of stainless steel baseboard installation steps.

Stainless steel baseboard installation steps of the installation buckle.

When installing the buckle, you need to place the buckle on the positioning ruler according to the positioning ruler mentioned above, close to the root of the wall, and fix it with a nail gun, and the spacing of the bayonet is about 400mm. In particular, it is necessary to pay attention to the need for a buckle at about 30mm at both ends of the wall.

3. Installation of stainless steel baseboard installation steps.

In the installation of all buckles, you need to cut the yin and yang corners according to the spacing and size of the buckles, and then tear off the protective film above and below the baseboard in order to play the silicone seal, and then you need to hang the groove on the baseboard inclined half on the upper mouth of the buckle according to the size, and then lift the back end of the pure sensitive baseboard up a little and then press it down against the wall, so that the upper convex card of the buckle completely enters the groove on the upper part of the baseboard, and at the same time gently pat the middle of the baseboard.

Stainless steel baseboard installation steps for installing baseboards.

After installation, it is necessary to check whether the baseboard is installed properly, and the gap between the wall, the ground and the skirting leg is sealed with silicone, and due to the principle of thermal expansion and cold contraction of the baseboard, an expansion joint of about 1cm needs to flow out during installation.

Stainless steel baseboard installation method: cement row nail fixing; Place the buckle on top of the positioning ruler, close to the base of the wall, press the upper end of the buckle with your fingers, and fix it with a nail gun. The length of the cement row nail is 32mm, the distance between the clamps is about 400mm, there should be a buckle at the interface of the two baseboards, and a buckle of about 30mm should be set at the end of the wall.

Stainless steel baseboard installation matters:

1. Ensure that all buckles are installed in the same straight line, and the error is to cut the yin and yang corners according to the size, and reserve about 2mm seams for silicone mortar hooks and deburring. Then remove the protective film under the baseboard and seal it with silicone. Neutral silicone is used for seals and slurry joints and is usually silver-gray or white in color.

2. Hang the groove of the baseboard with a good size on the button, lift the rear end of the baseboard up a little, and then press it down on the wall, so that the upper convex card of the buckle completely enters the groove of the baseboard, and tap the north of the baseboard. To install, start at one end and gradually press one clip into the other. Don't hammer.

3. After the installation is completed, seal the gap between the baseboard and the wall and the ground with silicone, paste the yin and yang corners and the 2mm gap reserved for horizontal connection with sandpaper, and then carry out the silicone mortar joint.

4. Tear off all the protective film of the baseboard, wipe off the remaining glue on the surface of the stainless steel with old powder, and use a brushed cloth to remove the black spots on the incision caused by glue heat.

There are many materials for baseboards, and stainless steel is one of them. So, how do you install a stainless steel baseboard? What are the precautions for the installation of baseboards? We've got you covered.

How to install stainless steel baseboards.

1. When installing the buckle, use a precise positioning ruler to clarify the height of the buckle installation part, and the height is determined according to the model and specification of the baseboard.

2. Eliminate the cement floating blocks on the wall, wall foot, and wall foot of the wall, where the baseboard is installed.

3. Put the buckle on the precise positioning ruler, against the foot of the wall, above the diastolic pressure buckle of the fingers, and fix it with a nail shooter.

4. There should be a buckle at the connection of the two baseboards, and the buckle interval should be 400mm up and down, and there should be a buckle at the end of the wall 30mm.

5. Understand the laser cutting angle line according to the size, grind and polish. Put the groove of the baseboard with a good size on the outer edge of the buckle, and then lift the back of the baseboard up a little and then press down against the wall, so that the upper end of the buckle is completely into the upper concave groove of the baseboard, and at the same time gently pat the middle of the baseboard.

6. When installing, gradually from one end, one buckle and one buckle are gradually pressed into the other end, do not hammer.

7. After the installation is completed, the gap between the baseboard and the wall and the ground is sealed with silicone, and the 2mm gap reserved for the yang angle line and the flat connection is pasted with masking tape and then made silicone mud seams.

Precautions for the installation of baseboards.

1. The baseboard was originally intended to cover the deformation joints of the floor and make the road surface more beautiful. Therefore, the edges of the baseboard crossing have to be scraped and leveled with a planer.

2. Whether it is a baseboard made of polymer materials, high-density boards, or wood, it is a particularly early bond of thermal expansion and contraction, so the baseboard against the corner of the wall should also be like a wooden floor, with a deformation joint of about 1cm.

3. The baseboard should be completely prepared against the wall, leaving no gap, so that it is more beautiful and generous, especially the foot of the wall. Before installation, the flatness of the wall should be checked.

4. The iron nails that fix the baseboard must be specially threaded nails, which have obvious fixed and immovable effects and are not easy to loosen. Everyone should pay attention to whether the manufacturer is shoddy.

<> which line installation steps mainly include: cleaning the wall foundation, determining the size of the buckle, installing the buckle, and installing the baseboard. The first is to clean the wall foundation, tidy the wall foundation, and the cement on the wall should be smoothed, and the wall surface needs to be checked whether it is straight.

The second is to determine the size of the buckle, which generally needs to be matched with the model of the baseboard. The second is to install the buckle, use a nail gun to fix the buckle, and keep the buckle code spacing 40 centimeters up and down. Finally, install the baseboard, cut the yin and yang corners, tear off the protective film, lift the baseboard up, press it again, and tap the baseboard to install it successfully.