How to install the dash cam rearview mirror to the car

Let me tell you, first unpack the package, right, then disassemble the parts you want, first remove the rubber sealing strip of the passenger door, when disassembling the A-pillar trim panel, if the vehicle has a round fixed cover, use a screwdriver to unscrew the internal screws, and then pull and disassemble the A-pillar trim panel on the passenger side with both hands, then use a screwdriver to disassemble the B-pillar trim panel, leaving a little gap between the roof and the B-pillar trim panel, and then connect the front and rear cables to the front lens, Place the alignment between the windshield and the ceiling by hand, install the rear camera above the rear glass**, tuck the wires all the way into the C-pillar trim panel, and use insulating tape to sort out the remaining rear wires.

No. The position where the dashcam is installed, the closer to the rear view in the car, the better, the angle of centering the shooting is larger, and the impact of the front windshield sight is minimal when installed near the core blue rearview mirror.

Install the dash cam between the inner rearview mirror and the front windshield, which is the most centered position. When installing in this position, it should be noted that if the recorder is too close to the inner mirror, it may affect the adjustment angle of the inner mirror.

The owner should pay more attention when installing, and it is very important to choose the right location, otherwise the owner will be severely punished after being found by the traffic police.

The steps to install the rear camera of the rearview mirror dash cam are as follows:

2. Then stuff the line into the ceiling from left to right, and pry it open at the corner.

<>4. Then route the rear along the window, and pry the sealant into the plug line.

<>7. Finally, bury the line in, and the rear camera of the rearview mirror dash cam will be installed successfully.

No. 1. Install it first. It is to use a clip to fix the recorder on the original car rearview mirror.

2. Planning. How to wire, whether to go directly to the cigarette lighter, or to connect to another place. Put a tray in the glove box, connected to the central control cigarette lighter, a recorder and a portable navigation, and an electronic dog, all powered by one pallet and three.

3. Wiring. Because of the glove box, the road to the back of the glove box, with the hand to stuff in, the mold there is also relatively loose, as long as the plug in a little, along the mold to the right, to the front of the upper right corner, as shown in the picture below to the door under the soft plastic. With a gentle pry of a flat change cone, the thread can be tucked in, and then it will be walked down.

4. Wear it out from below, as I said earlier, it was planned at the beginning, so it was so troublesome that you don't have to wear it around. The black hook let me take it off, the kind of hook with damping, which is convenient for cable routing, and it can be hung on that head when you walk well.

5. Connect the electricity from the cigarette lighter, and stick three pieces of transparent tape to the central control with one support and three traces.

There is no need to remove the rearview mirror, and now there is a kind of rearview mirror dash cam that is directly stuck on the rearview mirror.

The dash cam rearview camera installation process is as follows:

1. First of all, let's take a look at the various lines on the recorder, as shown below.

2. Be sure to plan well before doing things, and then take a look at the overall wiring diagram in the vehicle, as shown below.

3. After reading it, start construction, the current trend is to install the camera near the rear license plate of the car, then its wiring must follow the door crack, then you have to remove the guard plate.

4. Drill holes near this license plate, and then fix the camera here, just fix it with a shouting line.

5. Pass it along the trunk branch, and then prepare to enter the car first.

6. Follow the line in the car, and the final destination is the recorder.

7. The recorder that arrives at the final line is OK according to the instructions written on it.

Generally, the dash cam purchased comes with a 5-6 meter line. It can be mounted above the rear license plate from the trunk cable. It is also possible to route the cable from the roof of the car and attach the camera to the rear windshield with a suction cup.

However, it is recommended to install it yourself, or it is safer to find a master to install it at the cost of work.

Start by removing the original mirrors, remove the screws with a screwdriver, and pull them up slightly. After disassembly, install the rearview mirror dash cam. Generally, the rearview mirror recorder is installed with a special vehicle bracket, which can be fixed directly.

After the installation is fixed, hide the power cord of the rearview mirror, and then turn on the Hengzhao brother for testing.

Functions of the dash cam:

1.The dash cam can safeguard the legitimate rights and interests of the driver. Some pedestrians and non-motorized vehicles crossing the road may be extorted or blackmailed by drivers if they are not careful. If a dashcam is installed, it can provide direct and effective evidence for guessing the driver.

2.The installation of tachograph can enable the traffic police to deal with traffic accidents accurately and quickly, which can not only quickly evacuate the scene to restore traffic, but also create a smooth traffic environment.

3.The installation of a traffic recorder can effectively remind the driver that the driver does not dare to violate the rules casually, and the probability of a traffic accident will be greatly reduced.

4.When dealing with traffic accident cases, the court will make more accurate judgments in terms of sentencing and compensation, while providing effective evidence for the insurance company.

Millions of car purchase subsidies.

The dash cam vertical shot can prevent the person who is touched by the porcelain to have an opportunity, and can also provide a strong evidence to the traffic police in the event of an accident in the vehicle. It is believed that it is very necessary for the installation of tachographs. The current dash cam is divided into two kinds, one is a single-lens small-screen dash cam, and the other is a dual-lens rearview mirror tachograph, so how to install this car rearview mirror type remainder tachograph?

If it is a car owner with strong hands-on ability and confidence in himself, he can install it himself, and read the manual carefully before installation.

There are three main steps to installation.

1.Install Rearview Mirror Dash Cam Home Screen:At present, the main screen of this kind of rearview mirror is generally directly mounted on the rearview mirror through the fixed straps, which is very convenient.

2.Routing:Because this kind of dash cam basically has dual cameras, in addition to the wiring of the power, it is necessary to take the rear camera wiring, the wiring path is explained in the manual, and the rear camera is glued to the rear windshield through double-sided tape.

3.Debug:Insert the memory card, perform a simple commissioning, and the installation of the dash cam is complete.

The setting of the rearview mirror dash cam is very simple, take 360M320 as an example, touch the [standby screen off button] in the middle of the lower part of the server display screen to turn on, after turning on, the video recorder will gradually record by itself, and touch the [setting button] to enter the setting. 360M320 This tachograph setting selection is very clear and understandable, there is a logo plus text, and there are corresponding function keys below.

Rearview mirror dash cam setting option.

2. Intermediate: The time format of the video recorder can be changed by hand.

3. WiFi: After the WiFi is turned off, it is not easy for the recorder to create a WiFi network hotspot.

9. The display screen is automatically turned off: the setting is whether to turn on the display screen and turn off the screen automatically, and the default setting is not full of vacancy and automatically turns off the screen.

Rearview mirror dash cam security process.

1. Security server.

Use a bandage to fix the rearview mirror dash cam on the original rearview mirror, which can be very tight during actual operation and must be pulled hard.

2. Take power. There are a variety of power plan schemes, can take power from the armrest box, take power from the cigarette lighter mouth of the car and take power from its fuse box, take power from the armrest box, take power from the cigarette lighter mouth of the car is very simple, and the power from the fuse box is slightly more inconvenient, and the voltage reduction line must be reduced, and this kind of power method is suitable for customers who must stop for monitoring.

3. Wiring. After confirming the method of taking electricity, it can be eliminated and gradually wiring, taking the simple power from the fire port as an example, from the top of the windshield - the A-pillar - the passenger - the fire port.

4. Ann rear camera.

There are two assembly parts of the rear camera: one is the inside of the rear windshield; The other is the cornice of the trunk of the car. It is proposed to be installed under the trunk of the car, and the inside of the windshield laminated glass behind it is very vulnerable to weather hazards.

Millions of car purchase subsidies.