iPhone6 is not plugged in headphones, but the headphone mode is how to adjust back?

In the shutdown state, we unplug the earphones, find a needle, and gently poke the earphone hole twice, it may be that when the earphones are unplugged, the bouncing device inside does not return to its original position, we wrap the toilet paper with the needle after poking, wipe the inner wall of the earphone hole, and wipe off the dust covering it.

The iPhone 6 is a very popular smartphone that has a really great feature, which is the headphone mode. Headphone mode allows you to enjoy better sound quality and better sound effects while using headphones. However, there are times when you may encounter such a problem:

When you don't plug in headphones, iPhone 6 is still in headphone mode, what should you do at this time?

First of all, we need to know the cause of this problem. Normally, when you plug in the headphones, your iPhone 6 will automatically switch to headphone mode. However, sometimes when you unplug the headphones, your iPhone 6 doesn't automatically switch back to speaker mode, but still stays in headphone mode.

This could be because when you plugged in your headphones, your iPhone detected an issue that caused it to not switch back to speaker mode properly.

So, how to solve this problem? Here are a few possible workarounds:

Method 1: Restart your iPhone

Restarting your iPhone a bit might fix the problem. Long press the power button on your iPhone and slide to turn it off. Wait for a few seconds before pressing the power button to restart your iPhone.

Method 2: Check your headphone jack.

Sometimes, when you plug in the headphones, the dust or dirt in the jack may cause the iPhone not to detect the headphones properly. You can use some cleaning tools such as cotton swabs or jet canisters to clean the jacks.

Method 3: Check your settings.

You can also check your iPhone settings to see if there are any settings regarding the headphones. Go to Settings >** > Volume limits and make sure that your volume limits aren't turned on. You can also try resetting your settings by going to Settings> General> Reset, > Reset All Settings.

Method 4: Contact Apple customer service.

If none of the above methods can solve the problem, then you can contact Apple customer service. They may offer a more professional solution or recommend that you go to an Apple Authorized Service Provider for repairs.

In a word, when your iPhone 6 is in headphone mode and no headphones are plugged in, it can be a relatively common problem. However, there are several methods you can try above to solve this problem.

Apple6S displays the headphone mode, there are two major reasons, one is that the hardware of the mobile phone is malfunctioning, and the hardware is the poor contact caused by the dust or water ingress of the earphone socket; The second is to change the system settings of the Apple mobile phone, and the system may recognize the earphone mode error in some cases.

If there is a problem with Apple's 6S hardware, it may be that the metal piece of the headphone jack is out of position, use the refill to dial the headphone jack and pop the metal piece inside; It is also possible that the headphone socket has poor contact due to dust or water, or it is due to oxidation of the plug or jack due to humid air. You can use a cotton swab dipped in alcohol to rotate and wipe the earphone plug and mobile phone jack, and then unplug and unplug the earphones a few more times, or restart the mobile phone.

Problems with the Apple 6S system will also cause the earphones to be unplugged or in headphone mode. You need to change the settings: [Settings] - [General] - [Accessibility] - [Audio Calling Mode] - [Select Speaker].

Then dial**, select Use Speaker after connecting, and then switch the audio call mode to Automatic.

If you have tried all of the above methods and still can't get out of headphone mode, you may need to take your phone for repair.

Adjust the settings.

Plug in the headphones and unplug them.

Wipe the dust off the headphone jack.

Gently poke the headphone jack with a needle.

Factory reset.

Repair operation method:

Settings - General - Accessibility - Use of incoming calls in physical activity.

Use the iPhone's headphone access interface, turn on the iPod to listen**, then press pause, press the home button to return, turn off the iPhone, pull out the headphones, and then turn on, it can be solved, if you don't succeed in trying a few more times, it still doesn't work, long press Power Home to hard restart, and then when the white apple appears, pull out the headphones.

You can simulate the action of listening to **, but this time when you unplug the headphones, don't be too fast, and gently rotate and unplug them. Sometimes I unplug it too quickly, and the program of the phone does not respond, so I keep the headphone mode all the time.

Unplug the headphones in the shutdown state, find a needle, and gently poke the headphone hole twice, it may be that when the earphones are unplugged, the bouncing device inside does not return to its original position, after poking, wrap the toilet paper with the needle, wipe the inner wall of the headphone hole, and wipe off the dust covering it.

Factory reset.

Hardware problems are taken for repair.

Answer 1: In general, this is caused by the dampness of the mobile phone or the water entering the headphone jack, try to throw out the water in the earpiece, and then gently screw in the water with a cotton swab, and then use the hair dryer to turn on the hot air on low gear to slowly dry the remaining moisture, and restart the mobile phone;

2. It may also be due to poor contact in the headphone jack of the mobile phone, or it may be caused by foreign objects inside, use a cotton swab or paper towel to clean it up;

3. If it still can't be solved after cleaning, it may be caused by the failure of the headphone jack, and it is recommended to take the mobile phone to the after-sales maintenance point for inspection and repair.

First of all, it seems that if there is no sound in electricity, it is to enter the headphone mode.

6. It's not okay, it's a hardware problem and send it for repair

Thank you for adopting Good luck

It may be caused by a short circuit caused by moisture in the headphone jack of your mobile phone, or due to a foreign object that causes poor contact between the contacts in the headphone jack, which can be cleaned with a cotton swab or paper towel; If the problem still cannot be solved, it is recommended to check and repair at an after-sales service point.

The following is a detailed introduction: 1. In general, this is caused by the dampness of the mobile phone or the water entering the headphone jack, try to throw out the water in the earpiece, and then gently screw in the water with a cotton swab, and then use the hair dryer to turn on the hot air and slowly dry the remaining moisture, and restart the mobile phone; 2. It may also be due to poor contact in the headphone jack of the mobile phone, or it may be caused by foreign objects inside, use a cotton swab or paper towel to clean it up; 3. If it still can't be solved after cleaning, it may be caused by the failure of the headphone jack, and it is recommended to take the mobile phone to the after-sales maintenance point for inspection and repair.

It is the copper contact switch in the headphone jack that has poor contact or the center point is damaged and cannot be reset.

1. There is a copper contact in the headphone socket, and the opening and closing of the contact triggers the peripheral numerical control circuit to form a complete audio input and output, and the contact switch is connected in series with the external speaker, when the earphone is not plugged in, the switch reed and the external speaker are on, and the contact reed of the serial speaker will be opened when the earphone is plugged in, so the speaker is disconnected and connected to the earphone, and the speaker will be reset after the earphone is unplugged. The position of the circle in the picture.

Second, the situation that can be solved by yourself is:

1. The contacts of the earphone socket are adhered to, and the socket is plugged and unplugged several times to disconnect it and reconnect.

2. The dirt in the earphone jack causes poor contact, and it is possible to use anhydrous alcohol to clean the inside of the socket.

3. If you can't solve the problem by yourself, please go to the maintenance point to replace the headphone jack.

It's not like that. Apple6There is indeed that problem,That is, unplugging the headphones during listening to songs will cause no sound outside,Call**Only the speaker or headset can talk,Can't talk normally at all。 It's not an auto-pause thing.

The solution is to reboot and it will be fine. But I listen to the headphones so many times a day, I can't restart them so many times. There is also a hair dryer, I dare not say if I haven't used it, but I say it's useful, I still feel that the hair dryer won't blow all the dust in?

There is a great god who actually said that it is good to roll a paper towel into a roll and stuff it into the headphone hole and turn around. This trick is really good.,Test it yourself.,I feel like the apple is amazing.,And we want to wipe the apple with saliva.。。 After that, you don't have to have a paper towel when you go out.

In my case, there was too much dust in it, so I first stuffed it with a cotton swab to squeeze the dust to the front, and then used a toothpick to buckle out the dust that was squeezed in (a large one), and then the earphones were inserted and pulled out repeatedly.

I tried your method for a long time and it didn't work, so I came to a violent one Turn on NetEase Cloud and listen to songs with headphones, press and hold to reduce the sound while listening to the song, and rub back and forth on the headphone jack at the same time (that is, unplug it and plug it in) in less than 30 seconds.

Water got into the headphone jack. Poke it in with toilet paper, roll it a few times, and use a hair dryer to blow it hot for 2 minutes, taking care not to leave anything in it. Plug in and unplug the headphones, restart them a few times, and try more.

I'm wrapping a toothpick in a tissue, probably fine with the earphones, and wiping it inside the headphone hole, it's fine, maybe there is water inside.

In fact, it is that there are small parts stuck in it and it does not bounce back, directly put the mobile phone horizontally, knock a few times on the headphone port against the table, and control the strength by yourself, which can generally be solved.

If it is wet, it is recommended to use a hair dryer to heat, aim at the earphone jack 20cm away from the phone and turn off the phone and blow for 10 minutes.

The second method really works, I found so many methods on the Internet, I have tried them all, and the second one is good to try. Thanks thanks, thanks.

Blow the hair dryer on the headphone jack for two or three minutes and it will work! The common problem of iPhone induced by humid weather in the rainy season.

You can blow the headphone jack with a hair dryer, or take a cotton swab and stuff it into the headphone jack, which is a common problem of iPhones, and I have tried it.

Use the headphones to hit **, and unplug the headphones during the play, just test it yourself.

It may be that water enters the headphone hole of the mobile phone when it rains, and it is good to blot the water dry with paper.

Long press the home and power off buttons, and reboot is fine. Tried it yourself.

Don't get anything, don't panic! Shut down for half to an hour! Turn it on again.

You can wipe the headphone jack with a paper towel, which is very effective.

I've had this happen to me too, and I'm because of the water. Blow dry the jack first, wipe it with a paper towel, and then take a very thin cotton swab and poke it a few times.

It's good to dig for a toothpick for a while.

Take a hair dryer to blow the headphone jack, or take a cotton swab and stuff it into the headphone jack, this is a common problem of iPhone, I have also tried.