How the exterior wall of the building was divided into grids during construction.

Create a box and set up segments as needed, e.g. 5*5*1, so that there are 25 windows.

Converts a rectangle to a polygon.

Using the Face selection, box select all the faces that precede it.

Press the "Insert" button, and then select the "Polygon" method, so that each face, will shrink a little, and you will have a window frame.

Press the "Extrude" button again to extrude the selected face inward.

In general, the grid refers to the grid line between floors or the grid line above and below the window, which is horizontally along the floor. Partitioning refers to the effect of exterior wall paint made into imitation bricks, which can be divided into large bricks such as 600*800 and small bricks such as 60*240.

Exterior wall lattice joints according to the graphic calculation software exterior wall plastering engineering quantity set exterior wall lattice joints quota mother and mother.

Exterior lattice joints (also known as lead lines) are set to prevent cracking of wall stucco and are often used as wall decoration lines. The spacing is generally not more than meters, and the actual grid is determined according to the floor height line and window frame, as shown in Fig.:

First, calculated according to the actual paving area.

Second, what is the exterior wall lattice joint:

In order to prevent hollowing and cracking of the exterior wall, a separation joint is installed. Exterior wall materials, such as painting, insulation, and temperature deformation and expansion of exterior wall tiles.

Generally, 6mx6m is set together. In practice, due to the existence of doors, windows, and vertical lines, one is set up on two or three horizontal layers.

For specific methods, you can leave grooves, or you can use caulking glue and other materials.

See if you have a wall caulking line in your quota to increase the material, and if so, calculate the area of the wall with the divider. But when there are only a few separators, or when there is no caulking line in your quota, calculate the number of meters of separators, and supplement this material after the set of plastering quotas.

Incorporated into the wall engineering quantity, there is no sub-item.

According to the project experience accumulated in the past, Sino real stone paint engineers believe that in order to do a good job in the real stone paint grid treatment, we should pay attention to the real stone paint grid technology.

The real stone paint lattice technology pays attention to the following elements:

1) Real stone paint lattice shape.

In order to make the exterior wall effect not rigid, try not to choose a square grid during the construction of real stone paint, such as horizontal and long grids, vertical grids, and "work" word grids are a good choice. However, the use function of the building should be considered, such as a commercial unit office building should choose a more stable grid design, residential, shopping malls, schools, gymnasiums, etc. can choose a more lively grid plan.

2) The position of the real stone paint grid.

In order to make the spraying effect of real stone paint closer to the stone, in principle, the same grid as the stone can be used, such as the yin and yang angle grid, the window grid, and the building edge grid. However, considering the limitations of the stone, the real stone paint grid can not be divided in the yin and yang corners, it is recommended that the grid must be divided on the side of the window, and pay attention to try not to appear small pieces, small edges.

3) The size of the real stone paint grid.

It should be reasonably divided according to the height of the building, the general high-rise grid should be in, the multi-storey grid should be controlled in between, and the low-rise grid should be within 1.

4) The width of the lattice seam of real stone paint.

According to the size of the lattice area, the width of the lattice seam should be reasonably designed, generally in between, or it can be designed as a horizontal width, vertical narrow, horizontal and narrow lattice effect, but try to control the width of the lattice seam within 2.

5) The color of the lattice joints in the construction of real stone paint.

This detail is generally easy to overlook, but it is very realistic to affect the overall effect of the real stone paint, the general design principle is to form the color of the real stone paint and the color of the grid seam has a contrasting effect.

1. Separate the surface layer to avoid cracking of the surface layer, which is the same as the principle of the separator of cement mortar.

2. Decorative effect, real stone paint to make the effect of stone, it is necessary to have the seam of the block finish, and the grid line has the decorative effect of the seam.

The main purpose of doing grid lines is to avoid serious cracking of the large area of concrete base surface due to thermal expansion and cold contraction. Setting a certain number of lattice joints can reduce the area of the waterproof layer of a single piece of concrete, thereby reducing its deformation due to expansion and warping, and effectively coating cracks. At the same time, it is also convenient for construction to be bounded by the grid line, and the construction is carried out in a more orderly manner.

In addition, the grid line can also increase the aesthetics of the building façade without looking too monotonous. Chenguang real stone paint is water-based and environmentally friendly, with excellent quality, good anti-ultraviolet and anti-weathering performance, and strong self-cleaning function. After making grid lines, it looks more beautiful and realistic.

Prevents large-scale cracking and aesthetics.

1. Cause analysis:

1. The geometric size of the surface brick is inconsistent.

2. The surface of the screed layer is uneven, and the screed layer is not carefully checked.

3. Unlined bricks, elastic lines and hanging lines.

4. Failure to adjust the seams and inspect them in time.

Second, prevention and control measures:

1. Before the use of bricks, bricks should be selected and stored in a classified manner, and the shape is skewed, the corners are missing, the warping and the color is uneven, and the three categories of large, medium and small are divided into three categories with a sleeve plate, which are used for different parts.

2. When making a leveling layer, the verticality and flatness must be checked with a ruler, and its value should be within the allowable deviation range.

3. The modulus of the brick row requires that the horizontal seam is flat with the window sill, the vertical and sunny angle, the window is flat, and the whole brick is used, the wall elastic line, the large wall should be paved first, the window frame, window sill, and waist line should be accurately divided, and the horizontal cloud vertical control line should be made from top to bottom on the leveling layer.

4. The upper mouth of the brick should be guaranteed to be straight during operation, and after pasting a skin of bricks, the vertical joint should be subject to the bottom ash elastic line and the hanging vertical line, and the joints should be adjusted before the initial setting of the mortar, and the paste should be cleaned immediately after pasting, and checked by the ruler.

The common problems of exterior wall brick engineering are mainly hollowing, falling off and cracking. In order to control the occurrence of these problems, it is necessary to standardize the construction, as follows: 1. Prevent falling off, hollowing and cracks.

During construction, the base must be cleaned, the surface repaired and smoothed, and the wall surface is soaked with water. Before the use of exterior wall tiles, they must be soaked in water for no less than 2 hours, and then taken out to dry.

It's just a line. Then the grid bar will be indicated, and there will be a sample number of the leading node, according to which you can find the detailed map to know the method.

Does it mean paint facades? Coating joints can prevent cracking caused by thermal expansion and contraction, and should be combined with modeling design if there are modeling requirements. Elastic paint should be divided into at least one slit on each floor, and if it is imitation stone paint, it should be denser.

The lattice joints of the exterior wall painting are generally set through the lower mouth of the beam (the upper mouth of the window).

Use a putty knife to shovel from the crack to both sides, about 10 cm on each side. Then fill and scrape with putty powder on the exterior wall, then polish it with a sand cloth, and finally brush the paint! The above tools and materials are available at chemical stores.

Now there are ready-made plastic dividers and drip strips, which can be sandwiched in when plastering.

Are you talking about a plastering layer or a paint finish layer? Do you want to design the angle or the craftsmanship of the construction? Please be clear.