What are the flight direction requirements for DJI drones?

In order to ensure the normal flight of your aircraft, it is recommended that you fly in an open and interference-free flight environment, and please avoid using your aircraft in the following environments:

1. Pure color surface, such as pure black, pure white, pure red, pure green;

2. Surfaces with strong reflection or reflection;

3. Water surface or transparent surface;

4. The surface of a moving object, such as above **, above a shrub or grass blown by a strong wind;

5. In scenes where the lighting changes violently and rapidly;

6. Particularly dark (light less than 10 lux) or very bright (light greater than 10,000 lux) surface;

7. Material surfaces that have strong absorption or reflection of infrared rays, such as mirrors;

8. Particularly sparse textured surface;

9. The surface of an object with a high degree of texture repetition, such as a small lattice brick of the same color;

10. Rain, snow and other weather that may cause the aircraft to get wet.

11.Do not fly in bad weather, such as strong winds (wind speed 5 or above), snow, rain, foggy weather, etc.

12.Choose an open place with no tall buildings around it as the flight field. Buildings that use a large number of steel bars will affect the work of the compass, and will block the GPS signal, resulting in poor positioning of the aircraft or even impossible to locate.

13.When flying, stay in sight and stay away from obstacles, crowds, water, etc.

14.Do not fly in areas with high-voltage lines, communication base stations or transmission towers to avoid interference with the remote controller.

5.If you are flying above 5,000 meters above sea level, the performance of the aircraft battery and power system will be reduced due to environmental factors, and the flight performance will be affected, so please fly with caution.

16.In the Arctic and Antarctic Circles, the aircraft cannot fly in p-mode and can fly using a vision system.

DJI's drone has three flight modes.

1. GPS mode: suitable for novices, fixed-point positioning.

2. Attitude mode: Naza is not equipped with GPS, so it can only fly with this mode. The usage rate is average, and it cannot be fixed but can be set high. Attitude correction is required, which is suitable for players with some flying experience.

3. Manual mode: It can determine whether the center of gravity of the aircraft is appropriate, and it is said that it can be used to save the aircraft, or experienced masters are used for 3D flight, and few people use it. No fixed point, no automatic correction of attitude.

In aerial photography aircraft, the remote control is generally divided into three gears, and the gears of different models are different.

Introduction to the remote control gear.

The remote control is generally divided into three gears, and the gears of different models are different. If you want to understand the meaning of different models of remote control gears, you can refer to this content for help.

Applicable products: DJI RC, RC-N1 Remote Controller, DJI RC Pro, DJI Remote Controller with Screen.

Gear classification. Cine - C (T).

normal - n (p).

Sport - S gear.

Gear meaning and function.

C Gear: Displayed as "Smooth Mode" in DJI Fly, Steady Gear restricts the maximum flight speed, ascent speed, and descent speed on the basis of normal gear, making the aircraft more stable during shooting, and suitable for when you have flown to the shooting position and start shooting, which is conducive to the stability of the image and smooth rotation of the viewing angle.

N mode: Displayed as "Normal Mode" in DJI Fly, the GNSS module, vision system (if any), and infrared sensing system will be used to achieve accurate hovering, stable flight, and intelligent flight functions when the aircraft is in this gear. The flight speed in this gear is moderate, and you can also use a wealth of intelligent functions, it is recommended that you choose this gear to fly by default;

S Mode: Displayed as "Sport" in DJI Fly, it uses the GNSS module and the downward-looking vision system to achieve precise hovering and stable flight. This mode has the fastest flight speed, which is more suitable for racing, racing and experiencing the sense of control, but when in S mode, the visual obstacle avoidance function will be automatically turned off, so you need to pay attention to the flight environment and flight safety;

For novice users, it is recommended to choose N gear for a balanced flight experience and a wealth of smart features.

Gear diagram diagram. DJI Remote Control with Screen.

The DJI Remote with Display has the gear from left to right"t", "P", and "S" are the same when using the DJI Fly app, corresponding to "Stable (C", "N", and "Sport" (S), respectively.

DJI RC-N1 remote controller.

The leftmost part of the RC-N1 remote control in the early batch gear is "TriPod", that is, "T gear", and the subsequent batches are changed to "CINE", that is, "C gear", the two keys have different names and the same function, and we will collectively refer to them as "C gear" in the future.

DJI RC remote control with screen.

DJI RC Pro with remote control.

There are three flight modes: P mode (positioning), S mode (sport), and A mode (attitude).

The details are as follows:

Other precautions are as follows:

Skyhawk Brigade UAV Flight Training Center, remind you that it is best not to switch the flight mode, the GPS mode comes with stability and position information, so it is relatively simple to fly, and the flight is very small or not, but once you switch to the attitude mode or manual mode, the aircraft will be elegant, and the altitude will change, so it is more difficult to control, and it is not recommended for novices to switch. The mode switch button is in the upper left corner, and the attitude is switched back to GPS to interrupt the automatic return to home behavior when cutting off the automatic return to home or loss of control protection.

1.Definition and limits of DJI drone flight altitude.

When using DJI drones for shooting, aerial surveys, and other operations, flight altitude is a very important parameter. However, there are strict restrictions on the flight altitude of DJI drones. For general civilian UAVs, the maximum flight altitude is 120 meters, and when flying in a specific air traffic control area, the flight altitude of ordinary civilian UAVs is also limited.

Because of this, before flying, be sure to understand the local drone flight restrictions and comply with the relevant regulations.

2.Factors influencing the flight altitude of DJI drones.

When it comes to DJI drones, there are many factors that affect flight altitude. First of all, the maximum flight altitude of DJI drones is different depending on the model. Secondly, the flight environment is also a very important influencing factor, such as air pressure, temperature, humidity, etc., which will have an impact on the flight altitude of the drone.

In addition, the sensors and control systems carried by DJI drones will also affect its maximum flight altitude, and the better the control system and sensors, the higher its flight altitude.

3.High-altitude flight skills of the Osakura Land Frontier drone.

When DJI drones need to conduct high-altitude shooting or aerial surveys, they need to master some high-altitude flying skills. First of all, it is necessary to ensure that the power of the drone is sufficient, so as not to run out of power at high altitude. Secondly, it is necessary to reasonably set waypoints and carry out automated flights, which can reduce the shaking of the UAV track and ensure the image quality during high-altitude shooting or aerial survey.

Also pay attention to controlling the pitch angle of the drone to ensure the stability of the camera's angle of view.

4.The relationship between the flight altitude of DJI drones and the effect of aerial photography.

The flight altitude of the DJI drone will have a very important impact on the aerial photography effect. Generally speaking, high-altitude aerial photography can obtain a more vivid and three-dimensional image effect, and the terrain and the outline of buildings can be observed more clearly. The low-altitude aerial photography effect is more realistic, and the details on the ground can be clearer.

Therefore, when choosing different altitudes for aerial photography, it is necessary to determine the flight altitude according to the actual needs and purposes.

All in all, the flight altitude of the DJI drone is a very important parameter and there are strict restrictions. When operating a drone, be sure to comply with relevant regulations to ensure flight safety. In addition, mastering some high-altitude flying skills can improve the quality of aerial images, which can enhance the shooting results.

Second, the movement of the drone, up, down, left turn, right turn, forward, backward, left, right three, is the tilt adjustment of the lens and**four,**locked,After turning on the pure lead calendar,**The value recording screen will be interrupted,You can let the system automatically metering and then lock it。

First, the user starts the DJI drone and turns on the joystick. Second, the user clicks on the navigation and sets the navigation point. Finally, the user clicks on the auto-fly option on the controller.

How to set up DJI Air2 auto-follow? Start the aircraft and make the aircraft take off to more than 1m above the ground. Open the DJIFLYAPP on your phone, select the target in the frame of the camera interface, and click Follow. Select the following method, click Lock, and click Go.

Advanced settingsAs a novice, you only need to understand P-mode and F-mode agitation, and A-mode is not recommended.

Battery mounted on the drone in the main slot. Use a data cable to connect your tablet or phone to install the software. Install the rotors. After pressing the power button of the drone boot remote control, press and hold this button to turn it on.

The DJI drone operation tutorial is as follows: unpack and check all items to make sure that there are no missing items, and at the same time, like the Dodo Genie series, you can remove the gimbal protective cover first to ensure that the gimbal can move freely for self-inspection after booting.

Regardless of any meteorological requirements, fly well and land safely, even if there is no wind in the flight, you can hit it, as long as it is hit, it is your responsibility, and the product has no flaws.