Will the Apple 6S phone battery break the screen during the battery replacement?

To change the battery of this mobile phone, you need to disassemble the screen cable. So it's inevitable that there will be some contact with the screen. If your hands-on ability is not strong, it is recommended that you go to a mobile phone repair shop to replace it after buying the battery. If you have strong hands-on ability, you can change the battery on the net by yourself**.

The reason for the screen failure after the Apple 6plus battery replacement is that the screen socks are not installed properly, and the mobile phone screen can be disassembled and the cable can be reinstalled. The specific steps are as follows:

1. After the mobile phone is turned off. Using a pentagonal screwdriver, find and unscrew the two screws on both sides of the charging port on the bottom of your iPhone6 phone.

2. After unscrewing the bottom screw, use the suction cup to place the suction cup above the back button on the front of the phone. Make sure that the suction cup can effectively fit the phone screen.

3. Use a suction cup to separate the screen from the main unit, insert a triangular sheet between the screen and the fuselage, and use the triangular foil to separate the screen from the fuselage along the edge.

4. Turn on the screen, find the mobile phone cable on the right side of the connection between the screen and the host, use a Phillips screwdriver to unscrew the screws fixed on the interface cover, and remove the covering iron sheet of the screen cable. It should be noted that the screen and the body should not be turned over more than 90° to avoid breaking the cable.

5. Use a crowbar to slowly pry the screen that is not turned on. There are three rows of wires that separate the body from the screen.

6. After prying open the cable, reinstall the cable, and pay attention to fastening the cable. After fastening, tighten the cable cover.

7. Install the host and mobile phone screen together.

8. Finally, tighten the two screws at the bottom of the mobile phone to complete the installation cable.

If the mobile phone battery is broken, it can be replaced, find a professional or replace it yourself, and the specific method of replacing the battery is as follows:

1.After shutting down, use the relevant screwdriver to remove the two screws on the bottom of the phone.

2.After removing the set screws, remember to take out the SIM card first, and then use the suction cup tool to start disassembling the device from the screen.

3.It should be noted that the iphone6 mobile phone screen LCD panel is connected to the motherboard through a cable and fixed by a metal shield, so when disassembling the screen, be sure to pay attention to the cable at the top, and do not exceed this angle by standing upright at most 90 degrees. Locate and unscrew the screws that hold the screen wired in place.

It's a good idea to remove the screen when removing the battery, as the battery is secured with glue and it can be laborious to remove it. Unscrew the screws on the protective cover, and then remove the protective cover as well. This is shown in the figure below.

4.After disconnecting the cable between the screen and the inside of the fuselage, you can remove the iPhone6 screen panel, and the front screen panel is also fixed with stainless steel, which can protect the fragile LCD panel from impact and heat insulation.

There is a pull tab under the smartphone battery, which is gently pulled out in the direction of the sticky pull tongue, which can pull out the adhesive hidden at the bottom of the fuselage, similar to 3M's non-marking glue, as shown in the figure below.

6.After that, you can remove the built-in battery of the iPhone 6.

7.Plug in the new battery and fold off the connector. Ultra-thin double-sided tape to hold the new battery.

The connector only needs a little force to get back into position, but aligning the position can be a bit cumbersome and take some time. The original battery connector was folded down, so it's the same now. You can use a small pick or a thin metal file to press it down.

8.After installing the new battery, connect the battery cable. Next, connect the screen cable, and finally install the screen, fix the screws, and install the SIM card, and you can complete the iphone6 battery replacement.

1. If you have this problem with your iPhone, you can apply pressure on the screen or twist the device, which seems to be able to temporarily improve the situation.

2. If your phone is still under warranty, you can go directly to Apple's official after-sales service.

3. If the phone has passed the warranty period, then you can only seek help from a third-party repair shop, and they will help you replace the touch control chip, because Apple's after-sales personnel cannot replace the logic board or touch screen controller chip for us.

1. Some iPhone6 6Plus users reported that they encountered failures in the display and touch function, but even if the entire screen is replaced, it may not be completely repaired.

2. Usually at first, it only appears at the top of the screen with a pattern strip, but over time, the anomaly sometimes suddenly affects the bottom of the screen, and even the touch fails and the device response becomes worse.

3. The problem of abnormal screen is also said to be related to the distant iPhone6 6Plus "breaking the bent door".

iPhone screen failure is a more common glitch.

1. I have fallen, or I have fallen not long ago, the screen touch screen has been loosened, and after a period of time, the wiring will fall off directly.

Second, if it has been flooded, it can be used again when it is dry, as if it is fine. In fact, the motherboard must be cleaned, otherwise the circuit will rust and there will be problems after a period of time.

3. High imitation charger and charging cable. Many people give off the bag when they buy it, and when they get it back, it is a high imitation, and after using it for a while, it hurts the power supply. Directly scrap the phone, especially the Hong Kong version of the mobile phone.

Fourth, charging while playing with your phone will also hurt your phone. Sometimes the current is too high and burns the inner screen. Is there any way to fix this, check it, if the line is loose, change the line.

If the inner screen is broken, directly replace the screen assembly. If you change the screen, it is not good, it is the touch screen IC problem of the motherboard, the so-called touch screen IC is a chip that controls the touch screen, which can be replaced, but the process requirements are very high, this is a chip-level maintenance, and the general small shop will not. Only contact the after-sales center for repairs.

The battery life of the general iPhone is about 2 to 3 years, and the battery will have different degrees of damage beyond this time.

consumption, the actual capacity will be far less than the initial capacity, so that the battery life of the mobile phone can not meet the normal use of daily life. At this time, it is very necessary and beneficial to replace the iPhone battery, and the choice of battery should choose the original battery with a guarantee.

2. Turn off the phone, and use a screwdriver to remove the screws on the outside of the DAO phone.

3. Suction the phone screen with the suction plate. (Be careful not to use too much force) 4 When the screen is sucked up, use the triangle to slash along the screen. (It is also possible to replace the nail with a triangular piece).

5Open the cover of the phone and use a screwdriver to remove the metal bracket between the motherboard and the battery.

6. Slowly pull out the tape between the battery and the metal case with tweezers.

7. Attach new tape to the new battery.

8Put the new battery back into your phone.

9. Reattach the metal bracket, close the cover, and tighten the screws. You're done.

I sell it in a regular one.

After the center, bai direct sales,

It is recommended that you go to the after-sales center of the positive DAO regulations, because making an appointment before the regular after-sales center can not only waive the service fee of 100 yuan, but also have 180 days of after-sales protection, so you don't have to worry about after-sales problems after repair.

If you have money, you can change it, and money is everything.

It is more troublesome to change the apple.

You can go to the official physical store to see that your phone is not within the scope of free battery replacement Apple 6 and 6s have a batch with battery problems It has been confirmed that Apple replaces the battery for free, adopt yo.

There are probably three impacts:

1. Damage other parts of the phone. Apple is an all-in-one computer, and if you replace the battery by yourself, you may not be small enough to break other answer parts, such as fingerprints, microphones, etc.

2. No more warranty. If you replace the accessories yourself or repair it at an outside mobile phone store, even if the mobile phone is still under warranty, it will no longer be warranted.

3. The mobile phone is scrapped. If you are not so proficient, you may not only get the battery right, but also scrap the phone.

In short, there is still a risk in doing it yourself, and it is best to go for after-sales replacement.

Basically, there will be no impact on the situation, mainly when disassembling and assembling, you need to pay attention to the corresponding interface is not wrong, then it's OK, the most important thing is that the new battery is the original, otherwise the replacement frequency may be relatively high.

May damage other parts of the phone.

The specific impact is as follows:

1. Damage to other parts of the phone: Apple is an all-in-one machine.

Replacing the battery by yourself may accidentally damage other parts, such as fingerprints, microphones, etc.

2. No longer warranty: If you replace the accessories by yourself or repair it in an outside mobile phone store, even if the mobile phone is still within the warranty period, it will no longer be warranted.

3. Scrapping of mobile phones: If you are not so proficient, you may not only not get the battery right, but also scrap the mobile phone.

When replacing the battery of iPhone6 Plus, connect the screen data cable.

Disconnected,I found this problem when I changed the battery myself.,Keep it on.,The screen can't be separated from the fuselage by too much gap.,Let alone replace the battery.。 The landlord should not have installed the screen data cable back in place, and after the position was right, he had to press a little hard to press the connector into the bayonet. The problem you mentioned should be here, the connector does not snap into the bayonet, and the screen fails or dims after turning on the computer.

In addition, there is a difference in the length of several screws at the bayonet, which one can not be installed wrongly, otherwise, the longest one may drill the motherboard circuit or cause an open circuit or short circuit.