What s the deal with the solar overflow pipe that keeps leaking?

Causes of leakage at the overflow port of the solar water heater: 1. The inlet and outlet pipes are broken; 2. The sealing silicone ring is damaged; 3. Vacuum tube rupture; Fourth, the solenoid valve is damaged; 5. The sensor is damaged; 6. The computer board is damaged; 7. The water tank is broken. Repair method of solar water heater overflow leakage:

1. Replace 4-point aluminum-plastic pipe; 2. Replace the sealing silicone ring; (47 & 58) 3. Replace the vacuum tube; 4. Replace the solenoid valve; (12V and 24V) 5. Replace the sensor that matches the computer board; (Side-mounted and bottom-mounted) 6. Replace the same type of computer board; 7. Remove the water tank and return it to the factory for welding or replacement. Hope mine is helpful to you.

Solar overflow keeps leaking solution:

Mixing valves, pipelines, safety valves, etc. are clogged due to long use, in this case, only these parts need to be cleaned and dredged.

The last case is a ruptured inner tank. However, the inner tank is one of the most important parts of the water heater, and it is very expensive to replace**. Therefore, it is not recommended to replace the broken inner dan, and it is recommended to replace the water heater directly.

Specific reasons:

1. The pipeline is blocked. Leaks from solar spills are mainly caused by clogged pipes, so carefully inspect the pipes for rust or foreign objects.

2. Pipeline rupture. Pipe rupture is visible to the naked eye, and even a slight rupture can cause a leak in a solar overflow.

3. Aging of parts. Water leakage in a solar overflow may have a certain relationship with the aging of components. The aging of components will affect the overall performance of the solar energy, and eventually water leakage will occur.

4. The inner tank is ruptured. Solar water heaters mainly rely on solar energy to produce hot water, and once the inner tank ruptures, it will lead to abnormal water temperature and water leakage.

Dear, hello, I am happy to serve you, the answer to the following solar overflow non-stop leakage is caused by the water is not closed in time, according to the different control methods, the main reasons are: 1. Automatic control type of solar energy: water level sensor damage (common), water solenoid valve damage (possible), controller failure (rare), etc.

2. Ordinary mechanically controlled solar energy: damage to the float ball valve (common), damage to the manual water valve (possibly). If the meter is not displayed when the water leaks is not faulty, the probe is not faulty, and the probe is replaced; If the power supply of the instrument is unplugged and the water leaks, it may be a solenoid valve failure, replace the solenoid valve; If there is a parallel backup valve installed next to the solenoid valve when Nai Mingling is installed, this backup valve is generally closed, if it is opened, the water tank must be closed manually, otherwise the overflow port will always leak.

You can also find after-sales, if it is inconvenient to go up and unscrew the screw of the overflow port (put the hot water first), the leather cushion inside should be loose, just press the screws on the line, if it leaks again, the silicone rubber ring connected to the solar overflow pipe and Neidan is broken.

Here's why:1. Leakage caused by obstruction and corrosion of mixing valves, pipelines, safety valves and other accessories of water heaters;

2. Water leakage caused by the rupture of mixing valves, pipelines, safety valves and other accessories of the water heater;

3. The sealing gasket of the mixing valve, pipeline, safety valve and other accessories of the water heater is aging and cracked, and the water leakage is caused by the failure to achieve the sealing effect;

4. Water leakage caused by the rupture of the inner tank of the water heater.

Several faults of overflow leakage:

1. After the water is full at night in summer, there is a water leakage the next day. This kind of water leakage is not very large, that is, it is very slow to tick, this is a normal phenomenon, do not worry, the water is caused by heat expansion.

2. The overflow water flows into a line and keeps flowing down. The solenoid valve is not closed tightly, this situation is mainly caused by rust inside the solenoid valve, and the solenoid valve core is not closed tightly, which can be solved by cleaning the solenoid valve or replacing the solenoid valve.

Adjust the float valve to control the water level.

Keep the water surface 1 cm below the overflow to avoid thermal expansion and overflow.

AnswerGlad to answer your question: a leak from the solar overflow indicates that the water is overflowing, if it is a manual water fill, close the water supply valve, if it is an automatic water supply, there may be three reasons: the sensor is damaged; The solenoid valve is damaged; The thermostat is damaged.

Please ask the manufacturer's after-sales service personnel to check it. If the meter is not displayed when the water leaks is not faulty, the probe is not faulty, and the probe is replaced; If the power supply of the instrument is unplugged and the water leaks, it may be a solenoid valve failure, replace the solenoid valve; If there is a parallel backup valve installed next to the solenoid valve during installation, this backup valve is usually closed, if it is opened, the water tank must be closed manually, otherwise the overflow port will always leak.

The precautions for using a solar water heater are as follows:

1. When the weather is extremely hot and the water temperature is extremely high, the water supply valve must be used to limit the pressure and add water. It is strictly forbidden to add water after the water is exhausted. It is good to turn on the water before sunrise in the morning or two hours after the sun sets in the evening, so as to ensure the service life of the water heater.

2. Each water heater has an exhaust hole, and it is normal for water to flow out after the water is full, and it will stop after closing the water valve. The exhaust hole should not be artificially blocked.

3. The power of electric heating is 1500 watts, if it is used in cloudy days or when the water temperature is not enough in winter, do not plug in for a long time. The power must be turned off when bathing.

4. When the temperature is not too low, after the water is used up at night, there is still some hot water in the water heater (water in the vacuum pipe), which should be filled with water immediately to reduce the internal water temperature of the water heater, reduce the heat loss of the night, and make full use of the heat energy.

Hope it helps you and I wish you a great life.

If you add too much water, if you add too much water, it will be easy to overflow if the water level rises after the high temperature!

If it is automatic, it can adjust the water level control valve, and if it is not good, it can be considered that the control valve is broken!

Let's put the water out of the point first, and find a way to solve it!

Use a tube to drain the water out.

Wrap the raw material tape with screws of the same size as the spill and tighten the spill.

Maybe there is a problem with the mixing valve, have you checked the mixing valve?

The answer may be because of a leak in the vacuum tube of the solar energy. If the environment is in winter, it is recommended not to use vacuum tubes, because the vacuum tubes will be frozen; If it's summer, you don't need to worry about freezing the vacuum tubes. It should be noted that in summer, try to avoid water at noon, and water in the morning or evening, because the weather is hot at noon, it will cause the temperature in the vacuum tube to rise, and if you inject cool water at this time, it will cause the vacuum tube to crack, which will lead to solar water leakage.

It may be that the rubber ring of the solar is broken. If there is no leakage of the vacuum tube, you need to check the vacuum tube and bucket lid of the water tank, if the position of the hole between the water tank and the vacuum tube is leaking, or the bucket lid is leaking, it means that the silicone ring is broken.

It may be that the detection head in the solar spill hole is broken, and the solar spill will continue to leak. It may be a leak caused by the blockage and corrosion of solar mixing valves, pipeline safety valves and other accessories. It is possible that the solar's sensor is damaged.

If the solenoid valve is damaged, the solar overflow will continue to leak. Suggested solutions: 1. First of all, you can check whether the standby valve is closed, if the standby valve is opened, then the water tank is full to close manually, if it is not manually closed, then you need to adjust the standby valve to a closed state.

2. Check whether the valves of the solar energy are blocked and corroded, if this happens, then it needs to be replaced. 3. You need to find a professional maintenance personnel to come to the door to test, to see if the detection head of the solar overflow hole is damaged, or the solenoid valve is damaged, and you also need to check the sensor, if it is confirmed that these parts are damaged, then it needs to be repaired or replaced, and the problem of continuous leakage of the solar overflow can be solved after replacement.

There are two causes of solar leakage from the outlet pipe: leakage of the inner tank or aging of the outlet pipe seal.

Workaround:1If it is a leakage of the inner tank, you can only find a professional after-sales personnel to deal with it;

2.If it is caused by the aging of the sealing ring of the outlet pipe, the treatment method is to find a yarn or cotton thread and carefully wrap it around the leakage one by one. After wrapping, use 502 glue to drench the coil completely. Wait until the glue is dry.

Summary. 1. What is the cause of the leakage of the overflow port of the solar water heater?

1. It may be because of the mixing valve, pipeline and safety valve, these fittings are blocked, which will cause a large area of leakage.

2. It is also possible that it has been used for a long time, and there is a rupture, for example, the sealing gasket is aging, and the sealing effect cannot be achieved, which will also cause water leakage.

3. Another reason is that the inner tank of the water heater, if it is cracked due to the temperature difference, it will also cause the overflow port to slowly seep water.

What's the deal with a solar water heater overflow leak?

1. What is the cause of the leakage of the overflow port of the solar water heater 1. It may be because of the mixing valve, pipeline and safety valve, and these accessories are blocked, which will cause a large area of leakage. 2. There may be a judgment that the stool has been used for a long time, and it will be broken, for example, the sealing of the dense digging field stool is aging, and the sealing effect cannot be achieved, which will also cause the problem of water leakage. 3. Another reason is that the inner tank of the water heater, if it is cracked due to the temperature difference, it will also cause the overflow port to slowly leak water.

The above are the possible causes of water leakage.

1. If it is because of the failure of the mixing valve or pipeline, including the accessories such as the safety valve, you can directly replace the relevant accessories to solve the problem. 2. If the problem is caused by the leakage of the water tank, it is more expensive to replace, because the inner tank of a water heater is relatively high, according to the same, it is recommended to change to a new water heater. The best way to avoid this is to protect the liner from corrosion, and to clean and maintain it regularly.

For example, we need to clean the water heater every one or two years to prevent the breeding of scale, so as to effectively extend the service life of the hot touch water purifier.

The above are some ways to solve the water leak, I hope it can help you.

If you have any questions, please ask and wish you a happy life<>