When the computer is connected to the Internet, it shows what is going on with 769 and how to solve

Error 769: Unable to connect to the specified target.

Problem: This is when there is a problem with your computer's network equipment.

Solution: Open "My Computer" "Control Panel" "Network Connection" to check whether the local connection is there.

Disabled", if yes, just double-click on the local connection and see the status change to "Enabled". If you don't even have a local connection, then your network card is 100% wrong - either it doesn't work well or it is broken. Please contact your computer company, or solve it yourself.

Error 769 error, most of them are disabled on the network card, just enable it! The causes are generally caused by the user's misoperation or some firewall software and computer viruses, which are very common.

If the local connection is not found, the driver of the network card is usually lost or the computer does not detect the network card, you can reinstall it.

Error cause: The NIC is disabled.

Solution: Please right-click on the computer, select Properties, then select Device Management, and then look at the network card driver, if it is an "x", the network card is disabled, click the right button to activate the network card to solve the problem.

Broadband Internet access shows "Error 769" prompt, unable to connect to the specified destination, because the network card is disabled or the network card driver is damaged, you can contact human customer service to report the fault, and it will be dealt with for you as soon as possible.

Well, let's see for myself what's going on, I also encountered it today, it took a lot of effort, I was sweating profusely, I made it for a long time, I gave you an answer, first of all, see if there is a problem with your Mao connection, this situation is generally a problem with the network card, don't be too anxious, open my computer or online neighbor properties to see the local connection, if it is forbidden then you enable him, this is the key, if not, then observe the Mao at this time, just a light on, and then turn off the cat first, enable the local connection, and turn on the cat after 5 seconds, If the computer appears 678 at this time, then try to restart the computer, do not use the start button to restart, but use the key of the host to press the restart a few times, you can see that several lights of the cat began to gradually light up, at this time in the connection, done, good luck.

Your NIC driver is not installed properly. Otherwise, it is impossible for you to have no local connection in your online neighbor properties;

2. Your network card has been physically damaged. In this case, it doesn't matter how many times you install the driver. You must replace the NIC with a new one.

To check if there is a problem with the network card, you need to go to the device manager, open the network adapter, and see if there is a network card below, and the normal network card status is green. There may be 0 network cards under your network adapter.

If your network card is not broken, but the driver is not installed correctly, you can click on "Other Devices" under Device Manager to see if there is a device with a yellow question mark, if so, find your network card driver and install it, and see if the hardware will enter the network adapter. Yes, the correct driver will be installed on the network card.

If there is no other device, you need to "View" in the menu above the Device Manager, and then "Show Hidden Device", if the network card is here, don't bother, your network card has basically been damaged hardware. Buy another PCI network card, about 10 or 20 yuan. Install it and solve your problem.

If error **769 occurs, usually the NIC driver is disabled, it is recommended that you troubleshoot from the following aspects:

1. Check whether there is a "local connection" computer symbol in the lower right corner of the computer monitor, and whether the local connection is disabled.

2. Check whether the computer network card is disabled;

3. Check whether the NIC or NIC driver is normal.

Error **769 occurs, it is recommended that the following troubleshooting methods can be done:

1. Check whether there is a "local connection" computer symbol in the lower right corner of the computer monitor, and whether the local connection is disabled.

2. Check whether the computer network card is disabled;

3. Check whether the NIC or NIC driver is normal.

Broadband Connection Error 769 Error Cause:

1. The NIC is disabled;

2. The network card is damaged or the driver is lost.

Solution: 1. Right-click "Online Neighbors" - Properties, check whether there is a "local connection", if the "local connection" is gray, click the icon and select "Enable", you can connect to the network normally;

2. Restart the NIC or reinstall the NIC driver;

Restart method: Right-click "My Computer" - select "Properties" - click "Hardware" - enter "Device Manager" - select "Network Adapter".

Ask Netcom or Telecom staff.

If error **769 occurs, usually the NIC driver is disabled, it is recommended that you troubleshoot from the following aspects:

1. Check whether there is a "local connection" computer symbol in the lower right corner of the computer monitor, and whether the local connection is disabled.

2. Check whether the computer network card is disabled;

3. Check whether the NIC or NIC driver is normal.

If there is no arrears of broadband, connection problems, check the line, firewall settings, etc.

Broadband Connection Error 769 Error Cause:

1. The NIC is disabled;

2. The network card is damaged or the driver is lost.

Solution: 1. Right-click "Online Neighbors" - Properties, check whether there is a "local connection", if the "local connection" is gray, click the icon and select "Enable", you can connect to the network normally;

2. Restart the NIC or reinstall the NIC driver;

Restart method: Right-click "My Computer" - select "Properties" - click "Hardware" - enter "Device Manager" - select "Network Adapter".

Error 769 is generally caused by the network card and the computer not connected, usually caused by the local connection being disabled, ping under DOS to see if the connection between the cat and the computer is connected. If it doesn't work, uninstall the network card and reinstall it to see if it works. If it still doesn't work, then call ** to the customer service operator, and the maintenance personnel will come to repair it.

The local connection does not respond, the network neighbor right-click attribute - see if the local connection is disabled or there is no local connection - if the right-click is disabled to enable - if not--look at my computer right-click management - device manager - see if there is a network adapter with a yellow question mark - that is the network card driver drive it can be driven It is estimated that how to drive depends on the model of the computer?

769 The NIC device cannot be found or the NIC is disabled Check whether the NIC is corrupt Whether the NIC driver is digitally signed.