There is a problem with the glue binder, how to solve it

1. No glue;

2. No heating;

3. Poor molding;

4. There is more glue brushing at one end and less at one end;

5. Brush glue. Adjust the height of the glue pot, open the shells on the left and right sides of the glue binding machine, you can see that there are two hexagon screws on the left and right pillars, and you can also see that there is a screw at the bottom of the left and right columns. When the amount of glue on the top is small, lower it a little, loosen the screws at the bottom in the opposite direction, and then make a sample to observe whether it is suitable, and fix the screws on the left and right sides of the upper side after it is appropriate.

Fix the two 6s at the bottom as well.

The adjustment of the side glue, when there is one side on the back of the book can not be glued, the level of the clamp mechanism needs to be adjusted, when facing the outside of the machine can not be brushed with glue, when the clamp table is turned over, the clip table is just pressed on a capped screw, loosen the nut of the pressed screw, tighten the screw inward, adjust to be able to completely brush the glue, when the inner side can not be brushed with the glue, adjust it in the opposite way above.

The replacement of the heating rod, when the heating indicator light is not lit for a long time, it can be basically determined that the heating rod is burned out, first open the safety protection shell of the rubber pot, loosen the fixing screw of the heating rod, pull out the heating rod, and then replace the heating rod in the opposite order.

The cordless glue binder uses a hot melt glue. It is a glue that melts at a certain temperature and solidifies when cooled. The inside page, the cover is glued to it.

There is a common hot melt type machine that is very cheap, but it needs to use a special envelope. (There is glue on the inside of the envelope.) Different thicknesses require different envelopes).

Maybe it's because the quality of the film you bought is not good, but you seem to be in the wrong category, and this is the operating system.

The reason why the rubber pie installation machine is not energized: search for cover 1Power Cord Connection Issues:

Generally, it is caused by poor connection of the power cord or poor contact of the power cord. Solution: Check whether the power supply is properly connected and try to replace a power cable.

2.Check if the air switch is in the ON position. 3.

Emergency stop switch problem, general transportation in order to reduce damage, the emergency stop switch is generally in a depressed (closed) state, you can try to rotate to the right, the emergency stop switch pops up.

You see if it's the following cases:

1. The display light is not on.

If the display light is not on, first check whether the power is connected, connect the power supply and start it, and then check whether the rubber pot part is hot, if not, please check the circuit part.

2. The glue pot cannot be pushed.

If the rubber pot cannot be pushed normally, check whether the working temperature has been reached, and check whether the transmission mechanism has problems such as disconnection. There is a roller body mechanism in the inner direction of the rubber pot to detect whether it can rotate normally, and whether the four rollers up and down can roll normally.

3. The spine of the bound book appears square at one end and round at the other.

When binding the spine, if there is a square end and a round end, check whether the hardcover paperback conversion template is placed in accordance with the operating rules, check whether the top screw of the extruded template is loose, if it is loose, please take out the top screw to adjust.

4. Brush glue deviation.

When one side of the back of the book is not glued, it is necessary to adjust the level of the clamp mechanism, when facing the outside of the machine can not be brushed with glue, when the clamp table is turned over, it is seen that the clamp table is just pressed on a capped screw, and the quilt is loosened.

Press the nut of the screw, tighten the screw inward, adjust it until it can be fully brushed to the glue, when the inner side can not be brushed with glue, adjust it in the opposite way above. The adjustment of this part only needs to be adjusted a little at a time.

5. The glue brushing position is high or low.

When the power is off, open the side cover on both sides of the device, connect the base of the device and the upper glue brushing mechanism, and there are four screws, please debug up or down. Each time, you only need to make minor adjustments, and then brush to check whether it meets the standard.

6. Slide the book down when gluing.

If the book slides down while gluing, remove the clamping mechanism. Remove the rubber pads on both sides, take out the clips and add a gasket to the double layer of iron.

Hello, this is the heating plate heating, 1, there is a heating plate under the glue, there are two small columns, the live wire and the zero line, first check whether the two wires are aged or broken. 2. If not, check the circuit with a multimeter, and check the capacitor if there is a capacitor 3. If it is not checking the motherboard.

That may be the reason why your cover paper is too thin, I have also encountered it, if you don't need a cover when binding, then you have to pad a thicker cover paper under the white paper, otherwise it will be stuck. Because it is too thin, the sol will burst out to both sides at the moment of clamping, and if the paper is too thin, it will squeeze out of the gap of the splint and cause it to stuck. The problem I have now is that the splint clamp is not tight or simply does not move, and it is frustrating.

Find a hammer to knock open, the quality of the current glue binding machine is really not complimentary, the new machine has to be repaired twice in three days, so these conditions are normal, as long as your heart is good enough, you can withstand the toss and it will be fine.

Dear, I'm glad to answer for you Answer: What's going on with the glue binding machine is as follows: (1) If there is too much or too little side glue, you need to adjust the gap between the glue roller and the squeegee.

2) If there is too much or too little side glue, you need to adjust the height of the squeegee plate. (3) Check whether the rubber roller does not rotate or rotates flexibly. TG-660 glue binding machine appearance profile manufacturing, so that the machine is stuffy, stable, durable, beautiful.

Simple operation, easy to learn and understand. IntroductionProduct Category:Perfect Binder Details:

TG-660 plastic binding machine appearance profile manufacturing, so that the machine is solid, stable, durable and beautiful. Simple operation, easy to learn and understand.

Summary. For the problem of entering the repair mode, the following steps can be adopted:1

First, turn on the power switch of the glue binder, then press and hold the "Repair" button and the "Start" button at the same time until the indicator light of the glue binder lights up, indicating that it has entered the repair mode. 2.Then, in the maintenance mode, you can check the various parts of the glue binder, such as checking whether the tape is broken, checking whether the belt wheel is loose, checking whether the belt drive shaft is loose, etc.

3.Finally, in the maintenance mode, the glue binding machine can be repaired according to the inspection results, such as replacing the tape, replacing the belt wheel, replacing the belt drive shaft, etc. In summary, the steps to enter the glue binder repair mode are:

First turn on the power switch, then press and hold the "Repair" button and "Start" button until the indicator light of the glue binder lights up, indicating that it has entered the repair mode, and then according to the inspection results, the glue binder will be repaired.

For the problem of entering the repair mode, the following steps can be adopted:1First of all, turn on the power switch of the glue binder, then press and hold the "Repair" button, and at the same time press and hold the "Start" button until the indicator light of the glue binder lights up, indicating that it has entered the maintenance posture infiltration mode.

2.Then, in the maintenance mode, you can check the various parts of the glue binding machine, such as checking whether the tape is damaged, checking whether the belt wheel is loose, checking whether the belt drive leather shaft is loose, etc. 3.

Finally, in the maintenance mode, the glue binding machine can be repaired according to the inspection results, such as replacing the tape, replacing the belt wheel, replacing the belt drive shaft, etc. In short, the steps to enter the maintenance mode of the glue binder are: first turn on the power switch, then press and hold the "Repair" button and the "Start" button until the indicator light of the glue binder lights up, indicating that the maintenance mode has been entered, and then the glue binder will be repaired according to the results of the inspection book.

Can you add, I don't quite understand it.

For the problem of entering the maintenance mode of the glue binder, the following steps can be taken:1First of all, turn on the power of the glue binder, and then press the "Mode Noisy Early" button to enter the mode to select the hand-to-hand interface; 2.

In the mode selection interface, select "Maintenance Mode", and then press the "OK" button to enter the maintenance mode of the glue binding machine; 3.In the maintenance mode, you can check the parameters of the glue binding machine, check whether the various parts of the machine are normal, and make corresponding repairs and adjustments. In addition, before entering the glue binder maintenance mode, you should check whether the power cord of the machine is properly connected, and whether the various parts of the machine are installed correctly to avoid unnecessary losses.