How do I replace my car wiper blade? How to change the car wiper?

Remove the wipers.

This step is relatively simple, pull up the wiper spring arm rod to make the wiper stand up, you will find a square opening in the middle, press the plastic block inside, and at the same time the other hand goes up, you can pull out the wiper. At this time, remember to put the wiper spring arm back into the windshield slowly and carefully immediately, so as not to accidentally touch the spring and bounce back to smash the windshield.

If you buy a new wiper, replace it and install it in place, so you don't have to look at the steps below.

Remove the wiper strip.

Removed wipers with a plastic cap at each end. One of them is fixed and the other is active. Use a slight force to pry open the fixed cap with a screwdriver, and do not rush to pull out the strip at this time.

Because there is also a metal buckle, which plays the role of clamping and fixing the adhesive strip, use a screwdriver to gently pry it open a little, and the adhesive strip can be pulled out smoothly.

Replace the adhesive strip. If you buy a new rubber strip online, remember that the length of the rubber strip used in the main and co-pilot wipers of the Yinglang GT is 27 and 25 inches respectively, and if there is no suitable model, buy a slightly longer interception. The rubber strip has two and a half layers from the inside to the outside (the outermost is the rubber "blade" of the wiper), and the innermost layer is stuck in the groove of the wiper, loaded in, fastened with the metal buckle, and covered with a plastic cap, just like the original.

Install wipers.

This is the reverse step of the first step, align the square protrusion with the small hole in the spring arm rod and snap it on.

The steps to replace the wiper are as follows:In the first step, lift the metal wiper arm from the windshield, perpendicular to the windshield position and hold it stable.

In the second step, press the stopper and remove the old wiper blades, separating them from the metal arm.

Step 3: Insert the new wipers, gently turn the new wipers until the hook clicks into place and is secured, and put the wipers back on the windshield.

Wipers, also known as wipers, water dials, wipers or windshield wipers, are composed of electric motors, reducers, four-link mechanisms, wiper arm mandrels, wiper blade assemblies, etc., and are used to brush and scrape the equipment that is attached to the windshield of the vehicle to remove rain and dust to improve the visibility of the driver and increase driving safety.

Start by determining what type of wiper you have.

Please click Enter a description.

Remove the protective cover from the wiper you bought.

Please click Enter a description.

Then open the buckle here and aim the wiper of the car directly.

Please click Enter a description.

Pull down and snap the clip to complete the installation.

Please click Enter a description.

Then put the wiper down and add water to scrape.

Please click Enter a description.

Hello! How to replace the car wiper:

1. Lift the metal wiper arm from the windshield and keep it stable perpendicular to the windshield;

2. Press the plug and remove the old wiper blade to separate it from the metal arm;

3. Insert a new wiper and gently turn the new wiper;

4. Place the wiper back on the windshield until the hook clicks into place to secure it.

For your driving safety, please replace the windshield wiper in time. Hope it helps!

Generally, the service life of the wiper is one year. It doesn't matter if it's from a 4S store or bought from outside.

Determine that the wiper is time to change: Clean the glass surface before confirming. Touch the surface of the glass with your hands to make sure that the glass is free of scratches and raised particles. Wipe the wiper strip with a cotton cloth, strictly prohibit vigorous efforts, and confirm whether the strip is scratched, deformed or jagged.

Under normal circumstances, if there is still a waterline or the sound is particularly loud, or it is not clear, you can consider replacing the wipers.

Explanation: Wipers, also known as wipers, water picks, wipers or windshield wipers, are equipment used to brush and scrape away rain and dust attached to the windshield of vehicles to improve the visibility of drivers and increase driving safety. Because of the legal requirements, cars in almost all places carry windshield wipers.

Vehicles such as hatchbacks and minivans are also equipped with wipers in the rear windows. In addition to automobiles, windshield wipers are also installed in other means of transportation, such as trains and trams. Some part of the engineering equipment, hope to adopt Thank you.

The wiper is lifted and the buckle can be replaced, which is still more convenient.

Go to the repair shop and have someone replace it for you.

Generally, it is relatively simple to replace the wiper strip, as long as the model corresponds, you can see the shape of the wiper buckle and replace it.

<> "How to Replace Wiper Blades in a Car.

The steps to replace your car's wiper blades are as follows:

1.Raise the arm, lift the cover and pull down the wiper bracket, fold it up 80 degrees, and then remove it.

2.For the safety of the windshield, you can put something such as gloves on it, and then pull out the wiper blades.

3.Open the bottom two sides of the wiper and take out the Wu Brother wire card, it should be noted here that there is a groove on the card, which should be paired with the wiper protruding position of the party, and the installation process needs to be reversed.

Precautions for the use of car wipers:

1) If there is no rain, it can not be used, and it must not be dry scraped without water, because the friction resistance will be increased due to the lack of water, which will cause damage to the rubber wiper blade and the wiper motor.

2) If the rain is not heavy enough to activate the wiper blades, it should not be scraped, and be sure to wait until there is enough rain on the glass surface, which is enough to not block the driver's view.

3) It is not advisable to use wiper blades to remove dust from the surface of the windshield, even if you want to do this, you must spray glass water at the same time, and you must not dry scrape without water.

4) If there are solid things on the windshield, pigeons and other birds dry dung, do not directly use the wiper to scrape, please clean the bird droppings with your hands first, these hard things are easy to cause local injuries to the thin sheets of the wiper blades, resulting in the wiper wiper is not clean rainwater.

The wiper rubber strip needs to be removed before replacing the wiper rubber strip.

Check that the rubber strips at both ends of the wiper can't slide back and forth, and what can't slide is the part we want to remove.

After finding the rubber strip that can slide, we can remove the clip used to fix this end, generally speaking, the clip is not difficult to get off, if it is particularly tight, you can use needle-nose pliers to help disassemble.

After the clip is removed, we can see that the rubber strip to be replaced is fixed to the wiper through a metal buckle, and we only need to pry the metal buckle up with the clip or the like to remove the rubber strip.

The installation of a new wiper rubber strip is only destroyed in accordance with the steps just said and can be followed, but special attention should be paid to here that the metal buckle that fixes the rubber strip must be fixed tightly, otherwise the rubber strip will be offset in use, which will affect the use effect.

Before replacing the wiper blade, we need to confirm the repair location and wiper type of the replacement wiper blade.

The maintenance position of the wiper, we can open the vehicle instruction manual and find the opening method of the wiper maintenance position.

In fact, for most models, we can simply judge, firstly, open the key door, then turn on the wiper, when the wiper starts to work and is in the highest position, then we quickly turn off the key switch. At this time, observe whether the position of the wiper stays at the highest place, if the wiper stops and does not return to the original windshield, this is the maintenance position of the wiper, otherwise, we need to open the maintenance position of the wiper according to the vehicle instruction manual.

Next, we can replace the wiper, first check the type of wiper interface, which can be roughly divided into three types:

The first kind of gear is the U-shaped interface wiper, to replace this kind of wiper, it is necessary to turn the wiper rotor 90 degrees, and the wiper arm is in a vertical position, and press the wiper lock at the U-shaped mouth, and finally grasp the wiper to the opening direction of the U-shaped interface to push it out to be removed, and only need to push it in the reverse direction of the U-shaped outlet when installing.

The other is a plug-in wiper, this kind of wiper has a lock button directly above or on both sides of the wiper, press the lock button, pull out the wiper to remove, directly reverse insertion during installation, and hear the click.

The last one is the non-locking wiper, this kind of wiper replacement is very convenient, the wiper arm is erected, and then the wiper can be removed by rotating the wiper 90 degrees, and the same reverse order can be installed.

Regardless of the type of wiper, after the old wiper is removed, wrap the wiper arm with a towel and gently place it on the windshield to prevent the wiper arm from suddenly returning to its position and shattering the windshield.

Finally, in order to ensure that our vision is clear, we must ensure that the wipers are in good working condition.

If you want to change the wiper blade more clearly, it is very easy to answer, there are two small thin screws in the wiper blade, after unscrewing it, replace the new rain wiper blade directly, and it can be used normally.

Actually, I think you can ask those who have replaced the wipers how to replace them?

1.Start by lifting the metal wiper arm away from the windshield, holding it stable perpendicular to the windshield.

2.Then press the stopper, and remove the old wiper blade, separate it from the metal arm, insert the new wiper, and gently turn the new wiper blade.

3.Finally until the hook clicks into place to secure it, place the wiper back on the windshield.

1. Remove the original wipers; Press and hold the lower part of the wiper buckle of this product; Turn the buckle open; The wiper arm hooks the product; Cover the wiper buckle back (if you don't understand, you can go to the car beauty shop or repair shop to ask the master for help).

2. Before using the wiper; Please wash all the ash on the rubber sheet first.

3. If there are foreign objects such as oil, wax, dirt and so on on the windshield; Dispose of it before use. Otherwise, the wiper blades will not work properly; It will shorten the service life.

4. Spray cleaning agent when driving in the rain to get a better wiping effect and prolong the service life.

First of all, the wiper is erected, then the wiper is removed from the metal swing arm, a small metal hook bites on the original rubber strip to play a fixed role, pry the metal hook up, pull out the wiper rubber strip, pry open the wiper plastic plug on the other side, replace the new rubber strip, cover the plastic plug, clamp the metal hook, and make it bite and fix the new rubber strip.

Wipers, also known as wipers, water picks, wipers or windshield wipers, are equipment used to brush and scrape rain and dust attached to the windshield of vehicles to improve the visibility of drivers and increase driving safety. Because of the legal requirements, cars in almost all places carry windshield wipers.

On rainy days, when raindrops fall on the window glass, the view in front of the car is quickly obstructed, and vehicles, pedestrians, and scenery become blurred. At this point, turn on the wipers and the front of the car will be clear.

If you drive the vehicle in rainy weather, the wipers are not used or the wipers fail to work properly, which is very detrimental to driving safety.

Therefore, before heavy rain, you should check whether the car wiper is working properly.

In addition, in a rainstorm, the rapid and large raindrops hit the windshield glass, even if the wiper movement is fast, it is difficult to clean the raindrops, which affects the driver's vision, in order to ensure the safety of driving, should be stopped immediately.